Page 45 of 88
PERIODIC MAINTENANCE AND MINOR REPAIR
6-13
6 2. Remove the air filter case cover by
removing the screws.3. Remove the air filter element by
removing the screws.4. Lightly tap the air filter element to
remove most of the dust and dirt,
and then blow the remaining dirt
out with compressed air as shown.
If the air filter element is damaged,
replace it.
5. Install the air filter element by in-
serting it into the air filter case,
then installing the screws.
1. Air filter case cover
2. Screw (´ 4)
1. Air filter element
2. Screw (´ 3)
E_5kr.book Page 13 Tuesday, September 12, 2000 4:46 PM
Page 46 of 88

PERIODIC MAINTENANCE AND MINOR REPAIR
6-14
6
EC000082
CAUTION:_ l
Make sure that the air filter ele-
ment is properly seated in the
air filter case.
l
The engine should never be op-
erated without the air filter ele-
ment installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.
_6. Install the air filter case cover by
installing the screws. 7. Connect the hose.
8. Install the air filter case by insert-
ing the projection into the grom-
met, installing the bolts, then
tightening the clamp screw.
EAU00629
Adjusting the carburetor The carburetor is an important part of
the engine and requires very sophisti-
cated adjustment. Therefore, most car-
buretor adjustments should be left to a
Yamaha dealer, who has the neces-
sary professional knowledge and expe-
rience. The adjustment described in
the following section, however, may be
serviced by the owner as part of routine
maintenance.
EC000094
CAUTION:_ The carburetor has been set and ex-
tensively tested at the Yamaha fac-
tory. Changing these settings
without sufficient technical knowl-
edge may result in poor perfor-
mance of or damage to the engine. _
1. Projection
2. Grommet
3. Hose
E_5kr.book Page 14 Tuesday, September 12, 2000 4:46 PM
Page 79 of 88

8-1
8
EAU01038
8-SPECIFICATIONS
Specifications CS-01E
Model XVS250
Dimensions
Overall length 2,320 mm
Overall width 910 mm
Overall height 1,075 mm
Seat height 670 mm
Wheelbase 1,530 mm
Ground clearance 150 mm
Minimum turning radius 2,900 mm
Basic weight (with oil and full
fuel tank)
159 kg
Engine
Engine type Air-cooled 4-stroke, SOHC
Cylinder arrangement V type 2-cylinder
Displacement 249 cm
3
Bore ´ stroke 49 ´ 66 mm
Compression ratio 10:1
Star ting system Electric star ter
Lubrication system Wet sumpEngine oil
Ty p e
Recommended engine oil
classification API Service SE, SF, SG or
higher
Quantity
Without oil filter element
replacement 1.4 L
With oil filter element
replacement 1.6 L
Total amount (dry engine) 1.75 L
-20 -10 0
10 20 30
40
50 ˚C
SAE 10W-30
SAE 15W-40SAE 20W-40SAE 20W-50
SAE 10W-40
CAUTION:Be sure to use motor oils that do not contain anti-fric-
tion modifiers. Passenger car motor oils (often labeled
“ENERGY CONSERVING II”) contain anti-friction addi-
tives which will cause clutch and/or starter clutch slip-
page, resulting in reduced component life and poor
engine performance.
E_5kr.book Page 1 Tuesday, September 12, 2000 4:46 PM
Page 80 of 88
SPECIFICATIONS
8-2
8
Air filterDry type element
Fuel
Type Regular unleaded gasoline
Fuel tank capacity 11 L
Fuel reserve amount 3.4 L
Carburetor
Manufacturer MIKUNI
Model ´ quantity BDS26 ´ 1
Spark plug
Manufacturer/model NGK / CR6HSA or
DENSO / U20FSR-U
Gap 0.6–0.7 mm
Clutch typeWet, multiple-disc
Transmission
Primary reduction system Spur gear
Primary reduction ratio 3.130
Secondary reduction system Chain drive
Secondary reduction ratio 2.800
Number of drive chain
sprocket teeth (front/rear) 20/56
Transmission type Constant-mesh 5-speed
Operation Left footGear ratio
1st 2.643
2nd 1.684
3rd 1.261
4th 1.000
5th 0.821
Chassis
Frame type Double cradle
Caster angle 35°
Trail 135 mm
Tires
Fr o n t
Type Tube tire
Size 80/100-18 47P
Manufacturer/
modelCHENG SHIN / C-916
INOUE / MARBELLA NF27
Rear
Type Tube tire
Size 130/90-15 M/C 66P
Manufacturer/
modelCHENG SHIN / C-915
INOUE / MARBELLA NR31
E_5kr.book Page 2 Tuesday, September 12, 2000 4:46 PM