2001 YAMAHA WARRIOR 350 engine oil

8-19
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-8.frame
EL
1. Oil filter cover 2. Oil filter
3. O-ring
1. Couvercle du filtre à huile 2. Filtre à huile
3. Joint torique
1. Tapa del filtro de aceite 2. Filtro de aceite
3. Junta tórica
5. Remove the oil filter cover and oil filter.
6. Clean the oil strainer and oil filter with sol-
vent.
7. Check the O-ring for damage and replace
it if necessary.
8. Install the oil filter, O-ring, oil filter cover,
oil strainer, compression spring and drain
bolt. Tighten the drain bolt to the specified
torque.
CAUTION:

Before installing the drain bolt, be sure to in-
stall the O-ring, compression spring and oil
strainer.
9. Fill the engine with oil, and then install the
dipstick. Tightening torque:
Drain bolt (engine):
32 Nm (3.2 m·kg)
Filter cover bolt:
10 Nm (1.0 m·kg)

8-21
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-8.frame
EL
CAUTION:

Be sure no foreign material enters the crank-
case.
10. Warm up the engine for several minutes
at idle speed. Check for oil leakage while
warming up.
CAUTION:

If oil leakage is found, stop the engine immedi-
ately and check for the cause.
Recommended oil:
See page 10-2.
Oil quantity:
Periodic oil change:
2.4L
With oil filter replacement:
2.5 L
Total amount:
3.2 L

8-23
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-8.frame
EL
Oil pressure check
1. Put a cloth around the cylinder.
2. Slightly loosen the oil gallery bolt in the
cylinder head.
3. Start the engine and keep it idling until oil
begins to seep from the oil gallery. If no oil
comes out after one minute, turn the en-
gine off so it will not seize and find the
cause.
4. Start the engine, and then check the oil
pressure.
5. After checking, tighten the oil gallery bolt
to the specified torque.CAUTION:Be sure to check the oil pressure after replac-ing the engine oil. Tightening torque:
Oil gallery bolt:
7 Nm (0.7 m·kg)
1. Oil gallery bolt
1. Boulon de rampe de graissage
1. Perno del conducto de aceite

8-31
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-8.frame
EL
6. Inspect the element. If damaged, replace
it.
7. Apply SAE 10W30 motor oil to the ele-
ment.NOTE:The element should be wet but not dripping.
8. Apply all-purpose grease to the air filter
element seat.
9. Reinstall the element to the element
guide.
10. Reinstall the element assembly and parts
removed for access.NOTE:The air filter element should be cleaned every
20 ~ 40 hours. It should be cleaned and lubri-
cated more often if the machine is operated in
extremely dusty areas. Each time filter element
maintenance is performed, check the air inlet
to the filter case for obstructions. Check the air
cleaner rubber joint to the carburetor and man-
ifold fittings for an airtight seal. Tighten all fit-
tings securely to avoid the possibility ofunfiltered air entering the engine.
1. Unlock
1. Déverrouiller
1. Levántelo1. Element retaining plate 2. Guide
3. Air filter element
1. Plaquette de retenue d’élément 2. Guide
3. Élément du filtre à air
1. Element plate 2. Guía
3. Elemento filtrante

8-63
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-8.frame
EL
EBU00570
Cable inspection and lubrication
WARNING
Inspect cables frequently and replace if dam-
aged. Corrosion can result when the outer
covering of control cables becomes damaged.
Cables can also become frayed or kinked. Op-
eration of controls could be restricted, whichcould cause an accident or injury.
Lubricate the inner cables and the cable ends.
If the cables do not operate smoothly, ask a
Yamaha dealer to replace them.
EBU00737
Brake and shift pedal/brake and clutch lever
lubrication
Lubricate the pivoting parts of each lever and
pedal.Recommended lubricant:
Engine oil
Recommended lubricant:
Lithium-soap-based grease
(all-purpose grease)

9-7
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-
EL
EBU00526
B. STORAGE
Long term storage (60 days or more) of your
machine will require some preventive proce-
dures to guard against deterioration. After
thoroughly cleaning the machine, prepare for
storage as follows:
1. Fill the fuel tank with fresh fuel and add
fuel stabilizer (if available).
NOTE:

Use of fuel stabilizer eliminates the need to
drain the fuel system. Consult a Yamaha dealer
if the fuel system is to be drained instead.
2. Remove the spark plug, pour about one
tablespoon of SAE 10W30 or 20W40 mo-
tor oil in the spark plug hole and reinstall
the spark plug. Ground the spark plug
wire and turn the engine over several
times to coat the cylinder wall with oil.
3. Clean the drive chain thoroughly and lu-
bricate it. (See page 8-61.)
4. Lubricate all control cables.

10-1
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-SPEC-E.frame
EL
EBU00428
SPECIFICATIONS
MODEL YFM350X
Dimension:
Overall length
Overall width
Overall height
Seat height
Wheel base
Minimum ground clearance
Minimum turning radius1,840 mm
1,080 mm
1,080 mm
765 mm
1,200 mm
125 mm
3,500 mm
Basic weight:
With oil and full fuel tank 191 kg
Engine:
Type
Cylinder arrangement
Displacement
Bore
´
Stroke
Compression ratio
Starting system
Lubrication systemAir-cooled, 4-stroke, SOHC
Single cylinder, Forward inclined
348 cm
3


83.0
´
64.5 mm
9.2 : 1
Electric starter
Wet sump

Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-SPEC-E.frame
10-2
ER
1
111111191011

Engine oil:
Type
-20°
-10°0°10°20°30°40°
50°C
5W/30
10W/30
10W/40
20W/5020W/4015W/40

Recommended engine oil classification: API Service SE, SF, SG type or higherMODEL YFM350X
CAUTION
:
Be sure to use motor oils that do not contain anti-
friction modifiers. Passenger car motor oils (often
labeled “Energy Conserving”) contain anti-friction
additives which will cause clutch and/or starter
clutch slippage, resulting in reduced componentlife and poor engine performance.