2001 YAMAHA WARRIOR 350 lock

8-53
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-8.frame
EL
a. Cable length (46 ~ 50 mm)
a. Longueur de câble (46 à 50 mm)
a. Longitud del cable (46 ~ 50 mm)
4. Turn the adjusting bolt on the lever holder
so that cable length a is 46 ~ 50 mm.
5. Tighten the locknut on the lever holder.
WARNING
Operating with improperly adjusted brakes
could cause the brakes to malfunction result-
ing in reduced braking performance. This
could increase the chance of a collision or acci-
dent. After adjusting the parking brake, block
the rear of the machine off the ground and
spin the rear wheels. Check to make sure there
is no brake drag. If brake drag is noticed, per-form the adjustment again.

8-55
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-8.frame
EL
1. Locknut 2. Adjusting bolt A. 5 ~ 10 mm
1. Contre-écrou 2. Boulon de réglage
1. Contratuerca 2. Perno de ajuste
EBU00741
Clutch lever free play adjustment
The clutch lever free play should be adjusted to
5 ~ 10 mm.
1. Loosen the locknut at the clutch lever.
2. Turn the adjusting bolt at the clutch lever
in direction a to increase the free play or
in direction b to decrease the free play.
3. Tighten the locknut at the clutch lever.
If the specified free play cannot be obtained,
proceed with the following steps.
4. Loosen the locknut at the clutch lever.
5. Turn the adjusting bolt at the clutch lever
in direction a to loosen the cable.
6. Loosen the locknut at the crankcase side.
7. Turn the adjusting nut at the crankcase in
direction a to increase the free play or in
direction b to decrease the free play.
8. Tighten the locknut at the crankcase and
the clutch lever.
1. Locknut 2. Adjusting nut
1. Contre-écrou 2. Écrou de réglage
1. Contratuerca 2. Tuerca de ajuste

8-59
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-8.frame
EL
1. Upper wheel hub nut 2. Lower wheel hub nut
1. Écrou supérieur de moyeu de roue
2. Écrou inférieur de moyeu de roue
1. Tuerca superior del buje de la rueda
2. Tuerca inferior del buje de la rueda
EBU00352
Drive chain slack adjustment
1. Loosen the rear wheel hub nuts.
2. Loosen the adjuster locknuts on each side.
To tighten the chain, turn the chain adjust-
er clockwise. To loosen the chain, turn the
adjuster counterclockwise and push the
wheel forward. Turn each adjuster exactly
the same amount to maintain correct axle
alignment.
There are marks on each side of the swingarm
and on each chain adjuster. Use them to check
for proper alignment.
3. After adjusting, be sure to tighten the lock-
nuts and the wheel hub nuts.
Tightening torque:
Upper wheel hub nut:
120 Nm (12.0 m·kg)
Lower wheel hub nut:
60 Nm (6.0 m·kg)
1. Locknut 2. Adjusting bolt 3. Alignment marks
1. Contre-écrou 2. Boulon de réglage
3. Repères d’alignement
1. Contratuerca 2. Perno de ajuste
3. Marcas de alineación

8-87
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-8.frame
EL
5. Remove the bulb holder cover.
6. Turn the bulb holder counterclockwise
and remove the defective bulb.
WARNING
The headlight bulb is hot when it is on and im-
mediately after it is turned off. Wait for the
bulb to cool before touching or removing it.
You can be burned, or a fire could start if thebulb touches something flammable.
1. Bulb holder cover
1. Cache de la fixation d’ampoule
1. Cubierta del portabombillas1. Defective bulb
1. Ampoule défectueuse
1. Lámpara defectuosa

8-89
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-8.frame
EL
7. Put a new bulb into position and secure it
in place with the bulb holder.
8. Install the bulb holder cover.CAUTION:Make sure the bulb holder cover is securely fit-
ted over the bulb holder and seated againstthe reflector.
9. Install the headlight assembly and the
guard.
Adjust the headlight beam if necessary.
EBU00409
Headlight beam adjustmentCAUTION:It is advisable to have a Yamaha dealer makethis adjustment.
1. Vertical adjustment:
To raise the beam, turn the adjusting
screw clockwise.
To lower the beam, turn the screw coun-
terclockwise.
1. Vertical adjusting screw (´ 2)
1. Vis de réglage vertical (´ 2)
1. Tornillo de ajuste vertical (´ 2)1. Bulb holder cover 2. Bulb holder
3. Reflector
1. Cache de la fixation d’ampoule 2. Fixation d’ampoule
3. Réflecteur
1. Cubierta del portabombillas 2. Portabombillas
3. Reflector

9-1
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-
EL
EBU00418
CLEANING AND STORAGE
A. CLEANING
Frequent, thorough cleaning of your machine
will not only enhance its appearance but will
improve its general performance and extend
the useful life of many components.
1. Before cleaning the machine:
a. Block off the end of the exhaust pipe to
prevent water entry. A plastic bag and
strong rubber band may be used.
b. Make sure the spark plug and all filler caps
are properly installed.
2. If the engine case is excessively greasy,
apply degreaser with a paint brush. Do
not apply degreaser to the chain, sprock-
ets or wheel axles.
3. Rinse the dirt and degreaser off with a
garden hose. Use only enough pressure
to do the job.

9-9
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-
EL
5. Block up the frame to raise all wheels off
the ground.
6. Tie a plastic bag over the exhaust pipe
outlet to prevent moisture from entering.
7. If storing in a humid or salt-air atmo-
sphere, coat all exposed metal surfaces
with a light film of oil. Do not apply oil to
any rubber parts or the seat cover.
8. Remove the battery and charge it. Store it
in a dry place and recharge it once a
month. Do not store the battery in an ex-
cessively warm or cold place (less than
0 ˚C or more than 30 ˚C).
NOTE:

Make any necessary repairs before storing the
machine.