2001 YAMAHA TW125 wheel

Adjusting the engine idling speed ....................6-14
Adjusting the throttle cable free play ................6-15
Adjusting the valve clearance ..........................6-16
Tires .................................................................6-16
Spoke wheels ..................................................6-18
Adjusting the clutch lever free play ..................6-19
Adjusting the brake lever free play...................6-20
Adjusting the brake pedal position and
free play .........................................................6-21
Adjusting the rear brake light switch ................6-22
Checking the front brake pads and
rear brake shoes ............................................6-23
Checking the brake fluid level ..........................6-24
Changing the brake fluid ..................................6-25
Drive chain slack ..............................................6-25
Lubricating the drive chain ...............................6-26
Checking and lubricating the cables ................6-27
Checking and lubricating the throttle grip
and cable .......................................................6-28
Checking and lubricating the brake and
shift pedals .....................................................6-28
Checking and lubricating the brake and
clutch levers ...................................................6-29
Checking and lubricating the sidestand ...........6-29
Lubricating the rear suspension .......................6-29
Checking the front fork .....................................6-30
Checking the steering ......................................6-30Checking the wheel bearings ...........................6-31
Battery..............................................................6-31
Replacing the fuse ...........................................6-34
Replacing the headlight bulb ...........................6-35
Replacing a turn signal light bulb .....................6-36
Replacing the tail/brake light bulb ....................6-37
Supporting the motorcycle ...............................6-37
Front wheel ......................................................6-38
Rear wheel .......................................................6-39
Troubleshooting ...............................................6-41
Troubleshooting chart ......................................6-42
MOTORCYCLE CARE AND STORAGE .............7-1
Care ...................................................................7-1
Storage ..............................................................7-4
SPECIFICATIONS ...............................................8-1
Conversion table ................................................8-5
CONSUMER INFORMATION ..............................9-1
Identification numbers ........................................9-1
Key identification number...................................9-1
Vehicle identification number .............................9-1
Model label.........................................................9-2
TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9
789
5EK-9-E2 (TW125)<3.3Passport> 5/23/00 9:47 AM Page 6

4-1
EAU01114
PRE-OPERATION CHECKS
1
2
34
5
6
7
8
9 The condition of a vehicle is the ownerÕs responsibility. Vital components can start to deteriorate quickly and unexpect-
edly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leak-
age or loss of tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thor-
ough visual inspection, to check the following points before each ride.
EAU03328
Pre-operation check list
ITEM CHECKS PAGE
Front brake9Check operation, free play, fluid level and vehicle for fluid leakage.
3-4, 6-20, 6-23Ð6-25
9Fill with DOT 4 brake fluid if necessary.
Rear brake9Check operation, condition and free play.
3-5, 6-21Ð6-239Adjust if necessary.
Clutch9Check operation, condition and free play.
3-4, 6-19Ð6-209Adjust if necessary.
Throttle grip and housing9Check smooth operation.
6-15, 6-289Lubricate if necessary.
Engine oil9Check oil level.
6-9Ð6-129Add oil if necessary.
Drive chain9Check chain slack and condition.
6-25Ð6-279Adjust if necessary.
Wheels and tires9Check tire air pressure, for wear, damage and spoke tightness.
6-16Ð6-199Tighten spokes if necessary.
Brake and shift pedal shafts9Check smooth operation.
6-289Lubricate if necessary.
Brake and clutch lever pivots9Check smooth operation.
6-299Lubricate if necessary.
Sidestand pivot9Check smooth operation.
6-299Lubricate if necessary.
Chassis fasteners9Make sure that all nuts, bolts and screws are properly tightened.
Ñ
9Tighten if necessary.
5EK-9-E2 (TW125)<3.3Passport> 5/23/00 9:47 AM Page 23

6-3
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
10
*Wheels¥ Check runout, spoke tightness and for damage.
¥ Tighten spokes if necessary.ÖÖÖÖ
11*Tires¥ Check tread depth and for damage.
¥ Replace if necessary.
¥ Check air pressure.
¥ Correct if necessary.ÖÖÖÖ
12*Wheel bearings¥ Check bearing for looseness or damage.ÖÖÖÖ
13*Swingarm¥ Check operation and for excessive play.ÖÖÖÖ
¥ Lubricate with lithium-soap-based grease. Every 24,000km
14 Drive chain¥ Check chain slack.
¥ Make sure that the rear wheel is properly aligned.
¥ Clean and lubricate.Every 500 km and after washing
the motorcycle in the rain
15*Steering bearings¥ Check bearing play and steering for roughness.ÖÖÖÖÖ
¥ Lubricate with lithium-soap-based greaseEvery 24,000km
16*Chassis fasteners¥ Make sure that all nuts, bolts and screws are properly tightened.ÖÖÖÖ Ö
17 Sidestand¥ Check operation.
¥ Lubricate.ÖÖÖÖ Ö
18*Sidestand switch¥ Check operation.ÖÖÖÖÖ Ö
19*Front fork¥ Check operation and for oil leakage.ÖÖÖÖ
20*Rear shock absorber
assembly pivoting
points¥ Check operation and shock absorber for oil leakage.ÖÖÖÖ
¥ Lubricate with lithium-soap-based grease.ÖÖ
21*Carburetor¥ Check starter (choke) operation.
¥ Adjust engine idling speed.ÖÖÖÖÖ Ö NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING (´1,000 km)
ANNUAL
CHECK
1 6 12 18 24
5EK-9-E2 (TW125)<3.3Passport> 5/23/00 9:47 AM Page 32

6-17
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
EWA00040
wBecause loading has an enormous
impact on the handling, braking,
performance and safety character-
istics of your motorcycle, you
should keep the following precau-
tions in mind.
8NEVER OVERLOAD THE
MOTORCYCLE! Operation of
an overloaded motorcycle may
result in tire damage, loss of
control, or severe injury. Make
sure that the total weight of
rider, passenger, cargo, and
accessories does not exceed
the specified maximum load
for the vehicle.
8Do not carry along loosely
packed items, which can shift
during a ride.
8Securely pack the heaviest
items close to the center of the
motorcycle and distribute the
weight evenly on both sides.
8Adjust the tire air pressure with
regard to the load.
8Check the tire condition and
air pressure before each ride.
1a
Tire inspection
The tires must be checked before
each ride. If the center tread depth
reaches the specified limit, if the tire
has a nail or glass fragments in it, or
if the sidewall is cracked, have a
Yamaha dealer replace the tire imme-
diately.NOTE:
The tire tread depth limits may differ
from country to country. Always com-
ply with the local regulations.1. Side wall
a. Tread depthMinimum tire tread depth
(front and rear)1.6 mm
EW000079
w8Have a Yamaha dealer replace
excessively worn tires.
Besides being illegal, operat-
ing the motorcycle with exces-
sively worn tires decreases
riding stability and can lead to
loss of control.
8The replacement of all wheel-
and brake-related parts,
including the tires, should be
left to a Yamaha dealer, who
has the necessary profession-
al knowledge and experience.
5EK-9-E2 (TW125)<3.3Passport> 5/23/00 9:47 AM Page 46

6-18
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9 Tire information
This motorcycle is equipped with tube
tires.
EW000078
w8The front and rear tires should
be of the same make and
design, otherwise the handling
characteristics of the motorcy-
cle cannot be guaranteed.
8After extensive tests, only the
tires listed below have been
approved for this model by
Yamaha Motor Co., Ltd.
EAU00681
w8Have a Yamaha dealer replace
excessively worn tires.
Besides being illegal, operat-
ing the motorcycle with exces-
sively worn tires decreases
riding stability and can lead to
loss of control.
8The replacement of all wheel-
and brake-related parts,
including the tires, should be
left to a Yamaha dealer, who
has the necessary profession-
al knowledge and experience.
8It is not recommended to
patch a punctured tube. If
unavoidable, however, patch
the tube very carefully and
replace it as soon as possible
with a high-quality product.
EAU00685
Spoke wheelsTo maximize the performance, dura-
bility, and safe operation of your
motorcycle, note the following points
regarding the specified wheels.
8The wheel rims should be
checked for cracks, bends or
warpage, and the spokes for
looseness or damage before
each ride. If any damage is
found, have a Yamaha dealer
replace the wheel. Do not
attempt even the smallest repair
to the wheel. A deformed or
cracked wheel must be replaced.
8The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced.
An unbalanced wheel can result
in poor performance, adverse
handling characteristics, and a
shortened tire life.
FRONT
Manufacturer Size TypeBRIDGESTONE
130/80-18 66P TW31
REAR
Manufacturer Size Type
BRIDGESTONE
180/80-14M/C 78P TW34
5EK-9-E2 (TW125)<3.3Passport> 5/23/00 9:47 AM Page 47

6-22
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9 To increase the brake pedal free
play, turn the adjusting nut at the
brake rod in direction a. To
decrease the brake pedal free play,
turn the adjusting nut in direction b.
1
2
a
b
EAU00713
Adjusting the rear brake light
switchThe rear brake light switch, which is
activated by the brake pedal, is prop-
erly adjusted when the brake light
comes on just before braking takes
effect. If necessary, adjust the brake
light switch as follows.
Turn the adjusting nut while holding
the rear brake light switch in place.
To make the brake light come on ear-
lier, turn the adjusting nut in direction
a. To make the brake light come on
later, turn the adjusting nut in direc-
tion b.1. Brake light switch
2. Adjusting nut
ba
1
1. Brake pedal free play adjusting nut
EW000106
w8After adjusting the drive chain
slack or removing and
installing the rear wheel,
always check the brake pedal
free play.
8If proper adjustment cannot be
obtained as described, have a
Yamaha dealer make this
adjustment.
8After adjusting the brake pedal
free play, check the operation
of the brake light.
5EK-9-E2 (TW125)<3.3Passport> 5/23/00 9:47 AM Page 51

6-25
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
EAU00744
Drive chain slackThe drive chain slack should be
checked before each ride and adjust-
ed if necessary.
To check the drive chain slack
1. Place the motorcycle on a level
surface and hold it in an upright
position.NOTE:
When checking and adjusting the
drive chain slack, the motorcycle
should be positioned straight up and
there should be no weight on it.
a. Drive chain slack2. Shift the transmission into the
neutral position.
3. Move the rear wheel by pushing
the motorcycle to locate the tight-
est portion of the drive chain,
and then measure the drive
chain slack as shown.
4. If the drive chain slack is incor-
rect, adjust it as follows.
a
Drive chain slack:
35Ð60 mm
EAU03238
Changing the brake fluidHave a Yamaha dealer change the
brake fluid at the intervals specified in
the periodic maintenance and lubrica-
tion chart. In addition, have the oil
seals of the brake master cylinder
and caliper as well as the brake hose
replaced at the intervals listed below
or whenever it is damaged or leaking.
8Oil seals: Replace every two
years.
8Brake hose: Replace every four
years.
5EK-9-E2 (TW125)<3.3Passport> 5/23/00 9:47 AM Page 54

6-26
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
EAU03526
To adjust the drive chain slack
1. Loosen the brake pedal free play
adjusting nut and the axle nut.
2. To tighten the drive chain, turn
the adjusting plate on each side
of the swingarm in direction a.
To loosen the drive chain, turn
the adjusting plate on each side
of the swingarm in direction b,
and then push the rear wheel for-
ward.NOTE:
Make sure that both adjusting plates
are in the same position for proper
wheel alignment.1. Axle nut
2. Chain adjusting plate
3. Rear brake pedal free play adjusting nut
21
a
b
3
EC000096
cCImproper drive chain slack will
overload the engine as well as
other vital parts of the motorcycle
and can lead to chain slippage or
breakage. To prevent this from
occurring, keep the drive chain
slack within the specified limits.3. Tighten the brake pedal free play
adjusting nut, and then tighten
the axle nut to the specified
torque.
4. Adjust the brake pedal free play.
(See page 6-21 for brake pedal
free play adjustment proce-
dures.)
EW000103
wAfter adjusting the brake pedal
free play, check the operation of
the brake light.
EAU01106
Lubricating the drive chainThe drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly
wear out, especially when riding in
dusty or wet areas. Service the drive
chain as follows.
EC000097
cCThe drive chain must be lubricated
after washing the motorcycle or
riding in the rain.1. Remove all dirt and mud from
the drive chain with a brush or
cloth.
2. Spray a drive chain lubricant on
both sides and on the middle of
the chain, making sure that all
side plates and rollers have been
sufficiently oiled.NOTE:
For a thorough cleaning, have a
Yamaha dealer remove the drive
chain and soak it in solvent.
Tightening torque:
Axle nut:
90 Nm (9.0 mákg)
5EK-9-E2 (TW125)<3.3Passport> 5/23/00 9:47 AM Page 55