Page 79 of 122
![VOLVO V70 2001 Owners Manual 2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_08a.htm[4/4/2013 10:39:05 PM]
Replacing high/low beam headlight bulbs
The headlight bulbs must be replaced from the engine co VOLVO V70 2001 Owners Manual 2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_08a.htm[4/4/2013 10:39:05 PM]
Replacing high/low beam headlight bulbs
The headlight bulbs must be replaced from the engine co](/manual-img/45/58545/w960_58545-78.png)
2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_08a.htm[4/4/2013 10:39:05 PM]
Replacing high/low beam headlight bulbs
The headlight bulbs must be replaced from the engine compartment.
CAUTION:
Do not touch the glass on halogen bulbs with your fingers. Grease, oil or any other impurities can be carbonized onto
the bulb and cause damage to the reflector.
Be sure to use bulbs of the correct type and voltage.
To remove a defective low beam bulb:
Switch off all lights and turn the ignition switch to position 0.
Open the hood.
Remove the plastic cover over the bulb (1) by turning it counterclockwise.
Remove the connector (2).
Loosen the retaining spring (3) by first moving it to the right and then moving it down, out of the way.
Pull out the defective bulb. Note the position of the guide lug on the base of the bulb (4).
To install a new low beam bulb (H7):
Insert the new bulb, without touching the glass, with the guide lug upward (1). The bulb will only seat properly in
this position.
Move the retaining spring up and push it slightly to the left until it seats properly (2).
Press the connector into place on the bulb (3).
Reinstall the plastic cover and turn it clockwise until it is correctly in place (4). "TOP" must be upward.
NOTE: If the vertical aim of your headlights needs to be adjusted for any reason (e.g., towing a trailer for extended
periods), this should be done by an authorized Volvo retailer.
ProCarManuals.com
Page 80 of 122
2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_08a.htm[4/4/2013 10:39:05 PM]
pg. 113 Replacing bulbs
To remove and install a high beam bulb (HB3):
Switch off all lights and turn the ignition switch to position 0.
Open the hood.
Remove the cover by twisting it counter-clockwise.
Twist the bulb holder counterclockwise, pull it out and fit a new bulb. Note its position.
Refit the bulb holder. It can only be fitted in one way.
Screw the cover back on. The word TOP should be upwards.
Replacement of front parking light bulb
Switch off all lights and turn ignition key to position 0.
Remove the low beam cover by twisting counterclockwise.
Pull out the bulb and its socket. Replace bulb.
Press the bulb and its socket back into place.
Check that the new bulb lights.
Screw the cover back into place, "TOP" should be upwards!
ProCarManuals.com
Page 81 of 122
2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_08a.htm[4/4/2013 10:39:05 PM]
Changing the bulb in the turn signals at the front corners
Switch off all lights and turn ignition key to position 0.
Pull out the bulb and its socket by twisting counterclockwise. Replace bulb.
Press the bulb and its socket back into place.
Check that the new bulb lights.
pg. 114 Replacing bulbs
Replacement of bulbs in backup light, rear parking lights and rear fog
lights
Switch off all lights and turn the ignition switch to position 0.
Open the access panel.
Remove the sound insulation behind it.
Twist the bulb holder counterclockwise and remove it.
Press the bulb inward, twist it counter-clockwise and extract it.
Fit a new bulb.
Fit the bulb holder in place and twist it clockwise.
Refit the sound insulation and put the access panel back in place.
ProCarManuals.com
Page 82 of 122
![VOLVO V70 2001 Owners Manual 2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_08a.htm[4/4/2013 10:39:05 PM]
Replacement of rear turn signal and brake light bulbs
Switch off all lights and turn the ignition VOLVO V70 2001 Owners Manual 2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_08a.htm[4/4/2013 10:39:05 PM]
Replacement of rear turn signal and brake light bulbs
Switch off all lights and turn the ignition](/manual-img/45/58545/w960_58545-81.png)
2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_08a.htm[4/4/2013 10:39:05 PM]
Replacement of rear turn signal and brake light bulbs
Switch off all lights and turn the ignition switch to position 0.
Using a screwdriver, carefully pry off the speaker grille.
Pull out the red tab in the speaker.
Then press on the black pin above the extracted red tab and twist out the speaker.
Twist the bulb holder counter-clockwise, and withdraw it.
Fit a new bulb.
Fit the bulb holder in place and twist it clockwise.
Refit the speaker and press in the red tab.
Press the speaker grille back into position.
pg. 115 Replacing bulbs
Front fog lights (option)
CAUTION:
Avoid touching the glass on the bulb with your fingers.
Switch off all lights and turn the ignition key to position 0.
Turn the bulb holder slightly counter-clockwise to release it.
Replace the bulb. The shape of the base of the bulb corresponds to the shape of the bulb holder.
Reinstall the bulb holder by turning it slightly clockwise. "TOP" on the holder should be upward.
ProCarManuals.com
Page 83 of 122
2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_08a.htm[4/4/2013 10:39:05 PM]
Side direction indicator
Open the front door halfway.
From the inside of the fender, push the lamp housing out.
Turn the bulb holder 1/4 turn counter-clockwise and pull it out from the lens.
Remove the defective bulb by pulling it straight out.
Insert a new bulb.
Reinsert the bulb holder in the lens and press the entire unit back into place on the fender.
pg. 116 Replacing bulbs
License plate lights
Switch off the ignition.
Loosen the screws with a torx screwdriver.
Carefully pull out the lamp housing.
Turn the bulb holder counterclockwise and pull it out.
Pull out the defective bulb and insert a new one.
Reinsert the bulb holder into the housing and turn it clockwise.
Reinstall the housing and screw it in place.
ProCarManuals.com
Page 91 of 122
![VOLVO V70 2001 Owners Manual 2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_09.htm[4/4/2013 10:39:07 PM]
2 0 0 1
VOLVO V70
Chapter 9 - Specifications
pg. 135 Specifications
Label information136
Dimension VOLVO V70 2001 Owners Manual 2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_09.htm[4/4/2013 10:39:07 PM]
2 0 0 1
VOLVO V70
Chapter 9 - Specifications
pg. 135 Specifications
Label information136
Dimension](/manual-img/45/58545/w960_58545-90.png)
2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_09.htm[4/4/2013 10:39:07 PM]
2 0 0 1
VOLVO V70
Chapter 9 - Specifications
pg. 135 Specifications
Label information136
Dimensions and weights137
Engine/transmission specifications138
Oil/fluid specifications and volumes139
Fuel system, Distributor ignition system, Suspension140
Electrical system141
Volvo On Call142
pg. 136 Label information
B<>1 Vehicle Emission Control Information
Your Volvo is designed to meet all applicable emission standards, as evi-denced by the certification label on the
underside of the hood. For further informa-tion regarding these regulations, please consult your Volvo retailer.
2 Vacuum hose routing
(underside of hood)
3 Loads and Tire Pressures
(on inside of fuel filler door)
4 Model plate
Vehicle Identification Number (VIN). Codes for color and upholstery, etc. The plate is located in the engine
compartment, on the inside of the left front fender.
5 Vehicle Identification Number (VIN) *
The VIN plate is located on the top left surface of the dashboard. The VIN is also stamped on the right hand door
pillar.
6 Federal Motor Vehicle Safety Stan -dards (FMVSS) specifications (USA) and Ministry of Transport (CMVSS)
standards (Canada)
Your Volvo is designed to meet all applicable safety standards, as evidenced by the certification label on the facing
side of the driver's door. For further informa-tion regarding these regulations, please consult your Volvo retailer.
7 Child safety latch label
ProCarManuals.com
Page 96 of 122
![VOLVO V70 2001 Owners Manual 2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_09.htm[4/4/2013 10:39:07 PM]
All specifications are subject to change without prior notice.
pg. 140 Fuel system, Distributor ig VOLVO V70 2001 Owners Manual 2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_09.htm[4/4/2013 10:39:07 PM]
All specifications are subject to change without prior notice.
pg. 140 Fuel system, Distributor ig](/manual-img/45/58545/w960_58545-95.png)
2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_09.htm[4/4/2013 10:39:07 PM]
All specifications are subject to change without prior notice.
pg. 140 Fuel system, Distributor ignition system, Suspension
Fuel system
The engine is equipped with a multiport fuel injection system.
Distributor ignition system
Firing order: 1-2-4-5-3
Electronic ignition setting: Not adjustable
Spark plugs: Champion RC8PYP 8 (or equivalent)
Spark plug gap: 0.028-0.032" (0.7-0.8 mm)
Tightening torque: 18.4 ft. lbs. (25 Nm)
Replacing spark plugs
The spark plugs should be changed every 30,000 miles (48,000 km). However, city driving or fast highway
driving may necessitate changing after 15,000 miles (24,000 km) of driving. When installing new plugs, be sure
to fit the right type and use correct torque. When changing the plugs, check that the suppressor connectors are
in good condition. Cracked or damaged connectors should be replaced. When changing the spark plugs, clean
the terminals and the rubber seals.
WARNING!
The ignition system operates at very high voltages. Special safety precautions must be followed to prevent injury.
Always turn the ignition off when:
Replacing ignition components e.g. plugs, coil, etc.
Do not touch any part of the ignition system while the engine is running. This may result in a shock and bodily
injury.
Front suspension
Spring strut suspension with integrated shock absorbers and control arms linked to the support frame. Power-
assisted rack and pinion steering. Safety type steering column. The alignment specifications apply to an unladen
car but include fuel, coolant and spare wheel.
Rear suspension
Individual rear wheel suspension with longitudinal support arms, double link arms and track rods.
Wheel dimensions 15"16"17"
V70 FWD*
Toe-in, front (mm)
on the wheel rims: 0.7±0.70.8±0.80.8±0.8
on the tire side: 0.9±0.90.9±0.91.0±1.0
ProCarManuals.com
Page 108 of 122
![VOLVO V70 2001 Owners Manual 2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_11.htm[4/4/2013 10:39:17 PM]
2 0 0 1
VOLVO V70
HomeLink® Universal Transceiver (option)
pg. 161 HomeLink® Universal Transceive VOLVO V70 2001 Owners Manual 2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_11.htm[4/4/2013 10:39:17 PM]
2 0 0 1
VOLVO V70
HomeLink® Universal Transceiver (option)
pg. 161 HomeLink® Universal Transceive](/manual-img/45/58545/w960_58545-107.png)
2001 VOLVO V70
http://new.volvocars.com/ownersdocs/2001/2001_V70/01v70_11.htm[4/4/2013 10:39:17 PM]
2 0 0 1
VOLVO V70
HomeLink® Universal Transceiver (option)
pg. 161 HomeLink® Universal Transceiver (option)
HomeLink® Universal Transceiver
HomeLink® is an advanced system that can be programmed to learn the codes of three different remote controlled-
devices (e.g., garage door openers, remote lighting, entry door lock). HomeLink®'s sun visor-mounted transceiver,
powered by your car's electrical system, may then be used in place of your hand -held remote controls.
NOTE: For your security, the HomeLink® Universal Transceiver is designed to not function if you lock your car
from the outside. Programming the transceiver
1. The ignition switch must be turned to the "accessory" position (II) before programming the HomeLink® Universal
Transceiver.
2. Begin by erasing all 3 factory default channels. Hold down the two outside buttons (buttons 1 and 3 in the
illustration) on the HomeLink® Universal Transceiver for about 20 seconds, until HomeLink®'s indicator light begins
to flash. Then release the buttons.
3. Hold your hand -held transmitter (garage door opener, for example) 2 to 5 in. (5 to 12 cm) away from the
HomeLink® surface, keeping the indicator light in view. For placement questions, contact HomeLink® toll-free 1-
800-355-3515 (Internet: www.HomeLink®.jci.com).
4. Using two hands, push and hold both your hand -held transmitter's button and the transceiver button you wish to
program. The indicator light will flash first slowly, then rapidly. Rapid flashing tells you the HomeLink® button has
been successfully programmed. Release both buttons.
ProCarManuals.com