2001 TOYOTA SEQUOIA Wiring

FI1066
IN0D9±03
Z11554
Seal Lock Adhesive IN±4
± INTRODUCTIONREPAIR INSTRUCTIONS
4 Author: Date:
2005 SEQUOIA (RM1146U)
REPAIR INSTRUCTIONS
GENERAL INFORMATION
BASIC REPAIR HINT
(a) Prevent damage and maintain vehicle cleanliness by pro-
tective covering on the fender, seat and floor.
(b) During disassembly, keep parts in the appropriate order
to facilitate reassembly.
(c) Installation and removal of battery terminal:
(1) Before performing electrical work, disconnect the
negative (±) terminal cable from the battery.
(2) If it is necessary to disconnect the battery for in-
spection or repair, first disconnect the negative (±)
terminal cable.
(3) When disconnecting the terminal cable, to prevent
damage to battery terminal, loosen the cable nut
and raise the cable straight up without twisting or
prying it.
(4) Clean the battery terminals and cable ends with a
clean shop rag. Do not scrape them with a file or oth-
er abrasive objects.
(5) Install the cable ends to the battery terminals after
loosening the nut and tighten the nut. Do not use a
hammer to tap the cable ends onto the terminals.
(6) Be sure the cover for the positive (+) terminal is
properly in place.
(d) Check hose and wiring connectors to make sure that they
are connected securely and correctly.
(e) Non±reusable parts
(1) Always replace cotter pins, gaskets, O±rings, oil
seals, etc. with new ones.
(2) Non±reusable parts are indicated in the component
illustrations by the ºº symbol.
(f) Precoated parts
Precoated parts are bolts, nuts, etc. that are coated with
a seal lock adhesive at the factory.
(1) If a precoated part is retightened, loosened or
caused to move in any way, it must be recoated with
the specified adhesive.
(2) When reusing precoated parts, clean off the old
adhesive and dry with compressed air. Then apply
the specified seal lock adhesive to the bolt, nut or
threads.

B04770
IN±18
± INTRODUCTIONFOR ALL OF VEHICLES
18 Author: Date:
2005 SEQUOIA (RM1146U)
(4) Check that the VSC TRAC warning light blinks.
(5) After the measurement, remove the SST and re-
start the engine. At this time, make sure that the
VSC TRAC warning light is off.
(b) Notice in VSC operation.
(1) Removal and reinstallation of VSC±related compo-
nents may cause misadjustment of them. Do not re-
move or reinstall them unless necessary.
(2) When conducting VSC±related operations, do not
fail to make sure that the preparation and the finish-
ing of the operation are all performed in accordance
with the direction in this text.
3. FOR VEHICLES EQUIPPED WITH A CATALYTIC CONVERTER
CAUTION:
If a large amount of unburned gasoline flows into the converter, it may overheat and create a fire haz-
ard. To prevent this, observe the following precautions and explain them to your customer.
(a) Use only unleaded gasoline.
(b) Avoid prolonged idling.
Avoid running the engine at idle speed for more than 20 minutes.
(c) Avoid spark jump test.
(1) Perform spark jump test only when absolutely necessary. Perform this test as rapidly as possible.
(2) While testing, never race the engine.
(d) Avoid prolonged engine compression measurement.
Engine compression tests must be done as rapidly as possible.
(e) Do not run engine when fuel tank is nearly empty.
This may cause the engine to misfire and create an extra load on the converter.
(f) Avoid coasting with ignition turned off.
(g) Do not dispose of used catalyst along with parts contaminated with gasoline or oil.
4. IF VEHICLE IS EQUIPPED WITH MOBILE COMMUNICATION SYSTEM
For vehicles with mobile communication systems such as two±way radios and cellular telephones, observe
the following precautions.
(1) Install the antenna as far as possible away from the ECU and sensors of the vehicle's electronic
system.
(2) Install the antenna feeder at least 20 cm (7.87 in.) away from the ECU and sensors of the ve-
hicle's electronic systems. For details about ECU and sensor locations, refer to the section on
the applicable component.
(3) Do not wind the antenna feeder together with the other wiring as much as possible, also avoid
running the antenna feeder parallel with other wire harness.
(4) Check that the antenna and feeder are correctly adjusted.
(5) Do not install powerful mobile communication system.

V08423 Knock Sensor 1
GRECM
KNK
E1 12
E6
WIRING DIAGRAM
Wiring Diagram
This shows a wiring diagram of the circuit.
Use this diagram together with ELECTRICAL
WIRING DIAGRAM to thoroughly understand the
circuit.
Wire colors are indicated by an alphabetical code.
B = Black, L = Blue, R = Red, BR = Brown,
LG = Light Green, V = Violet, G = Green,
O = Orange, W = White, GR = Gray, P = Pink,
Y = Yellow, SB = Sky Blue
The first letter indicates the basic wire color and
the second letter indicates the color of the stripe.
DTC P0325Knock Sensor 1 Circuit Malfunction
CIRCUIT DESCRIPTION
Knock sensor is fitted to the cylinder block to detect engine knocking. This sensor contains a piezoelectric element which
generates a voltage when it becomes deformed, which occurs when the cylinder block vibrates due to knocking. If engine
knocking occurs, ignition timing is retarded to suppress it.
DTC No. DTC Detecting Condition Trouble Area
P0325No knock sensor 1 signal to ECM with engine speed,
1,200 rpm or more. Open or short in knock sensor1 circuit
 Knock sensor 1 (looseness)
 ECM
If the ECM detects the above diagnosis conditions, it operates the fall safe function in which the corrective retard angle
value is set to the maximum value.
 Diagnostic Trouble Code No. and Detection Item
 Circuit Description
The major role and operation, etc. of the circuit
and its component parts are explained.
 Indicates the diagnostic trouble code, diagnostic
trouble code set parameter and suspect area of
the problem.

± INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMSIN±33
33 Author: Date:
2005 SEQUOIA (RM1146U)
6. CIRCUIT INSPECTION
How to read and use each page is shown below.

PP±12
± PREPARATIONSFI
70 Author: Date:
2005 SEQUOIA (RM1146U)
(09808±01410)Holder
(09808±01420)Claw
(09808±01430)Bolt
09842±30070Wiring ºFº EFI Inspection

DIDFO±01
B17410
E5 E6
E7 E8E4 DI±34
± DIAGNOSTICSENGINE
228 Author: Date:
2005 SEQUOIA (RM1146U)
TERMINALS OF ECM
Each ECM terminals' standard voltage is shown in the table below. In the table, first follow the information
under ºConditionº.
Look under ºSymbols (Terminals No.)º for the terminals to be inspected.
The standard voltage between the terminals is shown under ºSTD Voltageº.
Use the illustration above as a reference for the ECM terminals.
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage
BATT (E4±3) ± E1 (E6±1)B±Y ± BRAl9t 14V+BM (E4±7) ± E1 (E6±1)W±G ± BRAlways9 to 14 V
IGSW (E4±9) ± E1 (E6±1)B±O ± BR
+B (E4±1) ± E1 (E6±1)B±R ± BRIG switch ON9 to 14 V
+B2 (E4±2) ± E1 (E6±1)B±R ± BR
IG switch ON9 to 14 V
MREL (E4±8) ± E1 (E6±1)B±W ± BRIG switch ON9 to 14 V
VC (E8±23) ± E2 (E8±28)G±B ± G±WIG switch ON4.5 to 5.5 V
VG (E8±30) ± E2G (E8±29)R±W ± B±WIdling, P or N position, A/C switch OFF0.5 to 3.0 V
THA (E8±22) ± E2 (E8±28)Y±G ± G±WIdling, Intake air temp. 20°C (68°F)0.5 to 3.4 V
THW (E8±21) ± E2 (E8±28)G±Y ± G±WIdling, Engine coolant temp. 80°C (176°F)0.2 to 1.0 V
VTA1 (E8 20) E2 (E8 28)BY GWIG switch ON, Accelerator pedal released0.5 to 1.2 VVTA1 (E8±20) ± E2 (E8±28)B±Y ± G±WIG switch ON, Accelerator pedal depressed3.2 to 4.8 V
VTA2 (E8 19) E2 (E8 28)PL GWIG switch ON, Accelerator pedal released2.0 to 3.1 VVTA2 (E8±19) ± E2 (E8±28)P±L ± G±WIG switch ON, Accelerator pedal depressed4.7 to 5.1 V
VPA (E4 18) E2 (E8 28)GR GWIG switch ON, Accelerator pedal released0.3 to 0.9 VVPA (E4±18) ± E2 (E8±28)G±R ± G±WIG switch ON, Accelerator pedal depressed3.2 to 4.8 V
VPA2 (E4 19) E2 (E8 28)LY GWIG switch ON, Accelerator pedal released1.8 to 2.7 VVPA2 (E4±19) ± E2 (E8±28)L±Y ± G±WIG switch ON, Accelerator pedal depressed4.7 to 5.1 V
VCPA (E4±26) ± EPA (E4±20)G±B ± G±WIG switch ON4.5 to 5.5 V
VCP2 (E4±27) ± EPA2 (E4±21)L±R ± L±BIG switch ON4.5 to 5.5 V

A07621A09776
1
2L±W
P±LOC1+
OC1±
OC2+
OC2± 17
L±B
R±L 1
2E6 C13
OCV (Bank 1)
C14
OCV (Bank 2)ECM
16
15
14 E6
E6
E6
± DIAGNOSTICSENGINE
DI±75
269 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTC P0010 displayed, check left bank OCV circuit.

If DTC P0020 displayed, check right bank OCV circuit.

Read freeze frame data using hand±held tester. Because freeze frame records the engine conditions
when the malfunction is detected. When troubleshooting, it is useful for determining whether the ve-
hicle was running or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc.
at the time of the malfunction.

DI±80
± DIAGNOSTICSENGINE
274 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR STRATEGY
P0011VVT system advance (Bank 1)
RltdDTCP0012VVT system retard (Bank 1)Related DTCsP0021VVT system advance (Bank 2)
P0022VVT system retard (Bank 2)
Main sensors/componentsCamshaft position sensor
Required sensors/componentsRelated sensors/componentsEngine coolant temperature sensor,
Crankshaft position sensor
Frequency of operationOnce per drive cycle
Duration10 sec.
MIL operationP0011, P0021: Immediate
P0012, P0022: 2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not presentSee page DI±18
Battery voltage11 V±
Throttle position learningCompleted
Engine RPM400 rpm4,000 rpm
Engine coolant temperature75C (167F)100C (212F)
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Deviation of valve timingMore than 5CA
OCV activation63 times or more
Response of valve timing1 sec./1CA or more
WIRING DIAGRAM
Refer to DTCs P0010 on page DI±73.
INSPECTION PROCEDURE
HINT:

Bank 1 refers to bank that includes cylinder No. 1.

Bank 2 refers to bank that does not include cylinder No. 1.

If DTC P0011, P0012 is displayed, check the bank 1 VVT system.

If DTC P0021, P0022 is displayed, check the bank 2 VVT system.

Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle
was running or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc. at
the time of the malfunction.

A02961
V5
VVT Sensor (Bank 1)ECM
1
2R
G
Y
LVVL+
VVL±
VVR+
E5 18
19
19
18
VVR±
1
2E5
E4
E4 V6
VVT Sensor (Bank 2)
± DIAGNOSTICSENGINE
DI±87
281 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTC P0016 is displayed, check left bank VVT sensor.

If DTC P0018 is displayed, check right bank VVT sensor.

Read freeze frame data using hand±held tester or OBD II scan tool. Because freeze frame records
the engine conditions when the malfunction is detected. When troubleshooting, it is useful for deter-
mining whether the vehicle was running or stopped, the engine was warmed up or not, the air±fuel ratio
was lean or rich, etc. at the time of the malfunction.
1 Check valve timing (Check for loose and jumping teeth of timing belt) (See page
EM±16).
NG Adjust valve timing (Repair or replace timing
belt).
OK
Replace ECM (See page SF±80).