Explanation of Maintenance Items
38
Engine Valve Clearance
Inspect for excessive lifter noise and engine vibration and adjust if necessary.
A qualified technician should perform this operation.
Exhaust Pipes and Mountings
Visually inspect the exhaust pipes, muffler and hangers for cracks, deterioration
and damage. Start the engine and listen carefully for any exhaust gas leakage.
Tighten connections or replace parts as necessary.
Fuel Lines and Connections, Fuel Tank Band and
Fuel Tank Vapor Vent System Hoses
Visually inspect for corrosion, damage, cracks and loose or leaking connections.
Tighten connections or replace parts as necessary.
Fuel Tank Cap Gasket
Visually inspect for cracks, deterioration and damage and replace if necessary.
Nuts and Bolts on Chassis and Body
Re tighten the seat mounting bolts and front/rear suspension member retaining
bolts to specified torque.
Propeller Shaft
Lubricate the propeller shaft spiders and slide yokes with lithium base chassis grease
and the double cardan joint with molybdenum disulfide lithium base chassis grease,
and re torque the bolt. Only a qualified technician should re torque the bolt.
Radiator Core and Condenser
Inspect for debris and signs of damage. Have any problem repaired immediately
by a qualified technician.
Spark Plugs
Replace at specified intervals. Install new plugs of the same type as originally
equipped. A qualified technician should perform this operation.
Steering Gear Box
Inspect for signs of leakage. If you discover any leakage, have it repaired imme
diately by a qualified technician.
C82785
F45388
C82977
No.2 PlugNo.1 Plug
Drain Plug
- TRANSFERTRANSFER ASSY (4WD)
31-35
3113 Author: Date:
(b) Install the transfer assy to the transaxle assy with the 2
bolts and 6 nuts.
Torque: 69 NVm (700 kgfVcm, 51 ftVlbf)
NOTICE:
Check that the gasket is installed to the transfer assy
before instaling them to the transaxle assy.
Install the transfer assy to the transaxle assy without
tilting.
When moving the transfer assy, do not hold the oil
seal on the both sides.
83. INSTALL ENGINE MOUNTING BRACKET RR (2AZ-FE ENGINE TYPE)
(a) Install the engine mounting bracket RR with the 3 bolts.
Torque: 64 NVm (652 kgfVcm, 47 ftVlbf)
84. INSTALL TRANSFER STIFFENER PLATE RH (2AZ-FE
ENGINE TYPE)
(a) Install the stiffener plate RH with the 5 bolts.
Torque: 34 NVm (350 kgfVcm, 25 ftVlbf)
85. INSTALL AUTOMATIC TRANSMISSION W/TRANSFER (3MZ-FE ENGINE TYPE)
(SEE PAGE 40-20)
86. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (3MZ-FE ENGINE TYPE) (SEE PAGE 14-149)
87. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (2AZ-FE ENGINE TYPE) (SEE PAGE 14-24)
88. INSTALL TRANSFER DRAIN PLUG
(a) Install the transfer drain plug with a new drain gasket.
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
89. INSTALL TRANSFER CASE NO.2 PLUG
(a) Install the transfer case No.2 plug with a new gasket No.2.
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
90. INSTALL TRANSFER CASE NO.1 PLUG
(a) Add oil up to 0 to 5 mm below the lower side of the plug
hole.
Oil quantity: 0.9 L (0.95 US qts, 0.79 lmp. qts)
HINT:
When adding oil, pour it slowly.
(b) Install the transfer case No.1 plug with a new gasket No.1.
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
