2001 TOYOTA AVALON P1155

A02032
HAFL ON
HAFR
(+)
(-)
- DIAGNOSTICSENGINE
DI-1 15
271 Author
: Date
:
2001 AVALON (RM808U)
DTC P1135 A/F Sensor Heater Circuit Malfunction (Bank
1 Sensor 1)
DTC P1155 A/F Sensor Heater Circuit Malfunction (Bank
2 Sensor 1)
CIRCUIT DESCRIPTION
Refer to DTC P0125 on page DI-43.
DTC No.DTC Detecting ConditionTrouble Area
P1135
When the heater operates, heater current exceeds 8 A
(2 trip detection logic)
Open or short in heater circuit of A/F sensor
A/F h tP1135
P1155Heater current of 0.25 A or less when the heater operates
(2 trip detection logic)
A/F sensor heater

ECM
WIRING DIAGRAM
Refer to DTC P0125 on page DI-43.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame records
the engine conditions when the malfunction is detected. When troubleshooting, it is useful for determining
whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was lean
or rich, etc. at the time of the malfunction.
1 Check voltage between terminals HAFL, HAFR of ECM connector and body
ground.
PREPARATION:
(a) Remove the glove compartment (See page SF-83).
(b) Turn the ignition switch ON.
CHECK:
Measure the voltage between terminals HAFL, HAFR of the
ECM connector and body ground.
OK:
Voltage: 9 - 14 V
OK Check and replace ECM (See page IN-30).
NG
2 Check resistance of A/F sensor heater (See page SF-79).
DI2H9-03

- DIAGNOSTICSENGINE
DI-17
173 Author
: Date
:
MANUFACTURER CONTROLLED
DTC No.
(See page)Detection ItemTrouble AreaMIL*Memory
P1130
(DI-106)A/F Sensor Circuit Range/Perfor-
mance Malfunction (Bank 1 Sen-
sor 1)
Open or short in A/F sensor circuit
A/F sensor
Air induction system
Fuel pressure
Injector
ECM

P1133
(DI-1 11)A/F Sensor Circuit Response
Malfunction (Bank 1 Sensor 1)
Open or short in A/F sensor circuit
A/F sensor
Air induction system
Fuel pressure
Injector
ECM

P1135
(DI-1 15)A/F Sensor Heater Circuit Mal-
function (Bank 1 Sensor 1)Open or short in heater circuit of A/F sensor
A/F sensor heater
ECM

P1150
(DI-106)A/F Sensor Circuit Range/Perfor-
mance Malfunction (Bank 2 Sen-
sor 1)
Same as DTC No. P1130
P1153
(DI-1 11)A/F Sensor Circuit Response
Malfunction (Bank 2 Sensor 1)Same as DTC No. P1133
P1155
(DI-1 15)A/F Sensor Heater Circuit Mal-
function (Bank 2 Sensor 1)Same as DTC No. P1135
P1300
(DI-1 17)Igniter Circuit Malfunction (No.1)
Ignition system
Open or short in IGF1 or IGT1 circuit from No.1 ignition coil
with igniter to ECM
No.1 ignition coil with igniter
ECM

P1305
(DI-1 17)Igniter Circuit Malfunction (No.2)
Ignition system
Open or short in IGF2 or IGT2 circuit from No.2 ignition coil
with igniter to ECM
No.2 ignition coil with igniter
ECM

P1310
(DI-1 17)Igniter Circuit Malfunction (No.3)
Ignition system
Open or short in IGF2 or IGT3 circuit from No.3 ignition coil
with igniter to ECM
No.3 ignition coil with igniter
ECM

P1315
(DI-1 17)Igniter Circuit Malfunction (No.4)
Ignition system
Open or short in IGF1 or IGT4 circuit from No.4 ignition coil
with igniter to ECM
No.4 ignition coil with igniter
ECM

P1320
(DI-1 17)Igniter Circuit Malfunction (No.5)
Ignition system
Open or short in IGF2 or IGT5 circuit from No.5 ignition coil
with igniter to ECM
No.5 ignition coil with igniter
ECM

P1325
(DI-1 17)Igniter Circuit Malfunction (No.6)
Ignition system
Open or short in IGF1 or IGT6 circuit from No.6 ignition coil
with igniter to ECM
No.6 ignition coil with igniter
ECM


DI-8
- DIAGNOSTICSENGINE
164 Author
: Date
:
2001 AVALON (RM808U)
HINT:
Take care not to turn the ignition switch OFF. Turning the ignition
switch OFF switches the diagnosis system from the check
mode to the normal mode, so all DTC, etc. are erased.
(10) After checking the DTC, inspect the applicable cir-
cuit.
4. FAIL-SAFE CHART
If any of the following codes is recorded, the ECM enters fail-safe mode.
DTC No.Fail-Safe OperationFail-Safe Deactivation Conditions
P0100Ignition timing fixed at 10° BTDCReturned to normal condition
P0110Intake air temp. is fixed at 20°C (68°F)Returned to normal condition
P0115Engine coolant temp. is fixed at 80°C (176°F)Returned to normal condition
P0120VTA is fixed at 0°The following condition must be repeated at least 2 times con-
secutively 0.1 V
VTA
0.95 V, SPD = 0 km/h
P0135
P0141
P0155
P1135
P1155
The heater circuit in witch an abnormality is detected is
turned offIgnition switch OFF
P0325
P0330Max. timing retardationIgnition switch OFF
P1300Fuel cutReturned to normal condition
5. CHECK FOR INTERMITTENT PROBLEMS
TOYOTA hand-held tester only:
By putting the vehicle's ECM in the check mode, 1 trip detection logic is possible instead of 2 trip detection
logic and sensitivity to detect open circuits is increased. This makes it easier to detect intermittent problems.
(1) Clear the DTC (See step 2).
(2) Set the check mode (See step 3).
(3) Perform a simulation test (See page IN-20).
(4) Check the connector and terminal (See page IN-30).
(5) Handle the connector (See page IN-30).
6. BASIC INSPECTION
When the malfunction code is not confirmed in the DTC check, troubleshooting should be performed in order
for all possible circuits to be considered as the cause of the problems. In many cases, by carrying out the
basic engine check shown in the following flow chart, the location causing the problem can be found quickly
and efficiently. Therefore, use of this check is essential in engine troubleshooting.
1 Is battery positive voltage 11 V or more when engine is stopped?
NO Charge or replace battery.
YES
2 Is engine cranked?