2001 SUZUKI GRAND VITARA abs

YH4
GRAND
VITARA
1. Clamp
2. Upper rod
1. Upper rod front bolt
2. Nut
3. Upper rod
4. Wheel speed sensor
harness bracket
(Toward outside of body)1. Upper rod
2. Bolt
5. Upper rod rear bolt
6. Washer
7. Body center
8. Front side
REAR SUSPENSION 3E-9
UPPER ROD
REMOVAL
1) Hoist vehicle and remove rear wheel.
2) If equipped with ABS, disconnect wheel speed sensor harness
clamp from left upper rod.
3) Remove upper rod.
INSTALLATION
1) Install upper rod to chassis frame and axle housing, referring to
figure for installing direction of bolts.
Nuts should not be tightened.
2) See figure for distinction of installing direction of left side upper
rod for vehicle equipped with ABS.
3) Connect wheel speed sensor harness clamp to upper rod (if
equipped with ABS).
4) Lower hoist and with vehicle in non-loaded condition, tighten
front bolt and rear nut of upper rod to specified torque.
Tightening Torque
(a): 90 N
.m (9.0 kg-m, 65 lb-ft)

YH4
GRAND
VITARA
1. Bearing retainer
2. Parking brake shoe
lever
3. Clearance1. Wheel speed sensor
1
L
REAR SUSPENSION 3E-11
4) Remove wheel speed sensor from rear axle housing (if
equipped with ABS).
CAUTION:

Do not pull wire harness or twist more than necessary
when removing rear wheel speed sensor.

Do not cause damage to surface of rear wheel speed
sensor or pole piece and do not allow dust, etc. to enter
its installation hole.
5) Check to ensure that there is clearance between rear wheel
bearing retainer and parking brake shoe lever. If no clearance
is found, loosen cable locking nut further to obtain clearance.
6) Using special tools (B) & (C) indicated below, draw out axle
shaft.
NOTE:
Use care not to pull brake back plate along with shaft.
CAUTION:
Pull out axle shaft using care so that upper and lower
brake struts and parking cable are not caught.
Special Tool
(C): 09943-35512
(B): 09942-15510
7) Rear axle shaft that was drawn out.
Shaft length ªLº:
Left side: 711.5 mm (28.0 in.)
Right side: 757.5 mm (29.8 in.)
8) If equipped with ABS, in order to remove sensor rotor from re-
tainer ring, grind with a grinder one part of the sensor rotor as
illustrated till it becomes thin.

YH4
GRAND
VITARA
1. Axle shaft
2. Wheel bearing
3. Press
1. Stud bolt
2. Hydraulic press
1. Rear wheel bearing
retainer ring
2. Grind with a grinder
3. Rear axle
3E-12 REAR SUSPENSION
9) Break with a chisel the thin ground sensor rotor, and it can be
removed (if equipped with ABS).
10) In order to remove the retainer ring from the shaft, grind with
a grinder two parts of the bearing retainer ring as illustrated till
it becomes thin.
CAUTION:
Be careful not to grind too far not to damage the shaft.
11) Break with a chisel the thin ground retainer ring, and it can be
removed.
12) Remove bearing from shaft by using hydraulic press.
13) Remove bearing retainer.
14) Remove stud bolt(s) by using hydraulic press.

YH4
GRAND
VITARA
[B]
1
2
[A]
1. Bearing retainer
2. Oil seal
3. Wheel side
4. Differential side
1. Stud bolt
2. Nut
3. Washer
4. Flange of axle shaft
1. Axle shaft
2. Bearing retainer
[A]: Vehicle without ABS
[B]: Vehicle with ABS
1. Bearing
2. Retainer ring
REAR SUSPENSION 3E-13
INSTALLATION
Install removed parts in reverse order of removal procedure, noting
the following.
1) Apply grease to oil seal lip as shown and install it to axle shaft.
NOTE:
Amount of grease applied to hollow in oil seal should be
more than 60% of its vacant space.
ªAº: Grease 99000-25010
2) Aligning serrations between new stud bolt(s) and flange, install
new stud bolt(s) by tightening nut as shown.
3) Install bearing retainer to shaft.
4) Press-fit wheel bearing and retainer ring as shown.
NOTE:

Use care not to cause any damage to outside of retainer
ring.

Refer to figure so that wheel bearing is installed in proper
direction.

YH4
GRAND
VITARA
1. Sensor rotor
1. Axle housing
1. Bearing retainer
(b)
3E-14 REAR SUSPENSION
5) For vehicle with ABS, press-fit new sensor rotor as shown.
NOTE:
Use care not to cause any damage to outside of retainer
ring.
6) Apply grease to axle shaft inner oil seal lip as shown.
ªAº: Grease 99000-25010
7) Apply sealant to mating surface of bearing retainer with brake
back plate.
NOTE:
Make sure to remove old sealant before applying it anew.
ªBº: Sealant 99000-31110
8) Install rear axle shaft to rear axle housing and tighten bearing
retainer nuts to specified torque.
NOTE:
When installing rear axle shaft, be careful not to cause
damage to oil seal lip in axle housing.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
9) Tighten wheel speed sensor bolt to specified torque (if
equipped with ABS).
Tightening Torque
(b): 21 N
.m (2.1 kg-m, 15.5 lb-ft)
10) Refill rear axle (differential) housing with new specified gear oil.
Refer to SECTION 7F for refill.
11) Install brake drum. (For details, refer to BRAKE DRUM
INSTALLATION in SECTION 5.)

YH4
GRAND
VITARA
1. Brake pipe flare nut
2. Brake pipe
3. Brake back plate
1. Bearing retainer
2. Parking brake shoe
lever
3. Clearance1. Nut 1. Wheel speed sensor
2. Wheel speed sensor coupler
3. Wheel speed sensor harness clamp
4. Wheel speed sensor harness
3E-16 REAR SUSPENSION
REAR AXLE HOUSING
REMOVAL
1) Drain differential gear oil.
Carry out steps 2) to 7) and 15) to 18) on both right and left
wheels.
Note that left wheel and its related parts are used in illustrations
in this section.
2) Remove rear brake drum. (Refer to steps 1) to 5) of BRAKE
DRUM REMOVAL.)
3) Disconnect brake pipe from wheel cylinder. With right side wheel
cylinder, disconnect 2 brake pipes.
4) For vehicle with ABS, disconnect wheel speed sensor coupler
and remove wheel speed sensor with its harness.
5) Remove rear wheel bearing retainer nuts from rear axle hous-
ing.
6) Check to ensure that there is clearance between rear wheel
bearing retainer and parking brake shoe lever. If no clearance
is found, loosen cable locking nut further to obtain clearance.

YH4
GRAND
VITARA
1. Flexible hose
2. E-ring
3. Brake pipe
4. Cross member1. LSPV stay
1. Hose
2. Axle housing
1. Propeller shaft
2. Differential carrier
REAR SUSPENSION 3E-17
7) Using special tools (B) & (C) indicated below, draw out axle
shafts. For vehicle equipped with ABS, remove wheel speed
sensor from axle housing before drawing out axle shaft.
NOTE:
Use care not to pull brake back plate along with shaft.
Special Tool
(C): 09943-35512
(B): 09942-15510
8) For vehicle without ABS, remove LSPV stay from axle housing.
9) Remove brake back plate from rear axle housing.
10) Disconnect brake pipe from flexible hose and remove E-ring
(front side).
11) Remove brake pipe clamps and pipes from axle housing and
disconnect breather hose from axle housing.
12) Disconnect propeller shaft and remove propeller shaft from
transmission.

YH4
GRAND
VITARA
3E-18 REAR SUSPENSION
1. Axle housing
2. Jack
1. Differential carrier
assembly
2. Differential carrier nut
1. Lower rod
2. Lower rod rear
mount nut
3. Shock absorber
1. Lower mount
bolt
13) For jobs hereafter, support rear axle housing by using floor jack
under axle housing.
14) Remove differential carrier assembly.
15) Loosen rear mount nut of upper rod but don't remove bolt.
16) Loosen rear mount nut of lower rod but don't remove bolt.
17) Remove rear axle side lateral rod mount bolt.
18) Remove shock absorber lower mount bolt.
19) Lower floor jack until tension of suspension coil spring be-
comes a little loose and remove rear mount bolt of upper , lower
and lateral rod.
20) Lower rear axle housing gradually.
21) Remove axle housing.