2001 SUZUKI GRAND VITARA DTC 46

YH4
GRAND
VITARA
5E1-28 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
-1. ABS hydraulic unit /
control module assembly
1-1. ABS pump motor relay
1-2. ABS pump motor
1-3. ABS fail safe relay
-2. ABS hydraulic unit/
control module connector
of harness
1. ABS hydraulic
unit / control
module connector
DTC 61 (DTC C1061) ± ABS PUMP MOTOR CIRCUIT
DESCRIPTION
The ABS control module monitors the voltage at the monitor terminal of the pump motor circuit constantly with the
ignition switch turned ON. It sets this DTC when the voltage at the monitor terminal does not become high / low
according to ON / OFF commands to the motor relay of the module (does not follow these commands).
INSPECTION
STEPACTIONYESNO
11) Check pump motor referring to item
ªABS HYDRAULIC UNIT OPERATION
CHECKº in this section.
Is it in good condition?Check terminals ªA11º
and ªA27º connection.
If connections OK,
substitute a known-
good ABS hydraulic
unit / control module
assembly and recheck.Go to step 2.
21) Ignition switch OFF.
2) Disconnect ABS hydraulic unit / control
module connector. (See Fig. 1)
3) Check for proper connection to ABS
hydraulic unit / control module connector
at terminal ªA27º.
4) If OK, then measure voltage between
terminal ªA27º of module connector
and body ground.
Is it 10 ± 14 V?Go to step 3.ªW / Blº circuit open.
3Measure resistance between connector
terminal ªA28º of ABS hydraulic unit / control
module assembly.
Is it infinite (
)?ªBº circuit open.Substitute a known-
good ABS hydraulic
unit / control module
assembly and recheck.
Fig. 1

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-29
1. Ignition switch
2. ABS hydraulic unit/
control module assembly
3. ABS hydraulic unit/
control module connector
of harness 2
1. ABS hydraulic
unit / control
module connector
DTC 63 (DTC C1063) ± ABS FAIL-SAFE RELAY CIRCUIT
DESCRIPTION
The ABS control module monitors the voltage at the terminal of the solenoid circuit constantly with the ignition
switch turned ON. Also, immediately after the ignition switch is turned ªONº, perform an initial check as follows.
Switch the fail-safe relay in the order of ON
OFF
ON and check if the voltage at 6 solenoid circuit terminals
changes to High
Low
High. If anything faulty is found in the initial check and when the voltage at all solenoid
circuit terminals is low with the ignition switch turned ON and ABS not operated, this DTC will be set.
INSPECTION
STEPACTIONYESNO
1Check battery voltage. Is it about 11 V or higher?Go to step 2.Check charging
system referring
to ªCHARGING
SYSTEMº section.
2Check ABS main fuse and connection. Is it in good
condition?Go to step 3.Repair and / or
replace fuse.
31) Ignition switch OFF.
2) Disconnect ABS hydraulic unit / control module
connector. (See Fig. 1)
3) Check proper connection to ABS hydraulic unit /
control module at terminal ªA11º.
4) If OK, then measure voltage between connector
terminal ªA11º, and body ground.
Is it 10 ± 14 V?Substitute a
known-good ABS
hydraulic unit /
control module
assembly and
recheck.ªW / Blº circuit open
or short to ground.
Fig. 1

YH4
GRAND
VITARA
5E1-30 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
DTC 71 (DTC C1071) ± ABS CONTROL MODULE
DESCRIPTION
This DTC will be set when an internal fault is detected in the ABS control module.
INSPECTION
STEPACTIONYESNO
11) Ignition switch OFF.
2) Disconnect connectors from ABS control module.
3) Check for proper connection to ABS control
module at all terminals.
Are they in good condition?Substitute a
known-good ABS
control module and
recheck.Repair or replace.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-31
1. Diagnosis
connector
(6 pins connector)
2. Diag. switch
terminal
3. Ground
4. Service wire
Brake
pedal
Ignition
sw.
Motor
Solenoid
Rear3.0 sec.
3.0
ON-VEHICLE SERVICE
PRECAUTION
When connector are connected to ABS hydraulic unit / control mod-
ule assembly, do not disconnect connectors of sensors and turn
ignition switch ON. Then DTC will be set in ABS control module.
ABS HYDRAULIC UNIT OPERATION CHECK
1) Check that basic brake system other than ABS is in good condi-
tion.
2) Check that battery voltage is 11V or higher.
3) With ªABSº warning lamp, check that no abnormality is de-
tected in ABS. Refer to ªDIAGNOSTIC TROUBLE CODE
(DTC) CHECKº in this section.
4) Lift up vehicle.
5) Set transmission to neutral and release parking brake.
6) Turn each wheel gradually by hand to check if brake dragging
occurs. If it does, correct.
7) With diag. switch terminal of diagnosis connector connected to
ground by using service wire, turn ignition switch ON and check
if ªABSº warning lamp indicates DTC 12.
8) Turn ignition switch OFF.
9) Perform following checks with help of another person.
Brake pedal should be depressed and then ignition switch
turned ON by one person and wheel should be turned by
another person's hand. At this time, check that:

Operation sound of solenoid is heard and wheel turns only
about 0.5 sec. (Brake force is depressurized).

Operation sound of pump motor is heard and pulsation is felt
at brake pedal.
10) If all 4-wheels cannot be checked during one ignition cycle
(OFF
ON), repeat Steps 8) and 9) till all 4 wheels are
checked.
If a faulty condition is found in Steps 9) and 10), replace hydrau-
lic unit / control module assembly.
11) Turn ignition switch OFF and remove service wire from diagno-
sis connector.

YH4
GRAND
VITARA
7B1
AUTOMATIC TRANSMISSION (4 A / T) 7B1-1
GENERAL DESCRIPTION7B1- 3 . . . . . . . . . . . . . .
CLUTCH / BRAKE FUNCTIONS 7B1- 5. . . . . . . . .
TABLE OF COMPONENT OPERATION 7B1- 6. . .
ELECTRONIC SHIFT CONTROL
SYSTEM 7B1- 7. . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOMATIC TRANSMISSION
DIAGNOSIS7B1-17 . . . . . . . . . . . . . . . . . . . . . . . . . .
PRECAUTION IN DIAGNOSING
TROUBLE 7B1-20. . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLE 7B1-21. . . . . . . . . .
Customer Problem Inspection Form 7B1-23. . .
Malfunction Indicator lamp (MIL)
Check 7B1-24. . . . . . . . . . . . . . . . . . . . . . . . . . .
ªO / D OFFº Lamp Check 7B1-24. . . . . . . . . . . . .
ªPOWERº Lamp Check 7B1-24. . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Check 7B1-24. . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Clearance 7B1-24. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) Table7B1-24 . . .
Fail-Safe Table 7B1-25. . . . . . . . . . . . . . . . . . . . .
Visual Inspection 7B1-26. . . . . . . . . . . . . . . . . . .
A / T Basic Check 7B1-27. . . . . . . . . . . . . . . . . . .
Trouble Diagnosis Table 1 7B1-28. . . . . . . . . . .
Trouble Diagnosis Table 2 7B1-28. . . . . . . . . . . Trouble Diagnosis Table 3 7B1-29. . . . . . . . . . .
Scan Tool Data 7B1-30. . . . . . . . . . . . . . . . . . . . .
Inspection of PCM and Its Circuit 7B1-30. . . . .
Wire Harness and Connectors 7B1-30. . . . . . . .
Diagnostic Flow Table A-1 7B1-31. . . . . . . . . . .
Diagnostic Flow Table A-2 7B1-33. . . . . . . . . . .
Table B-1 ªO / D OFFº Light Circuit
Check 7B1-35. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-2 ªO / D OFFº Light Circuit
Check 7B1-36. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-3 ªPOWERº Light Circuit
Check 7B1-37. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-4 ªPOWERº Light Circuit
Check 7B1-38. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0705 Transmission Range
Sensor (Switch) Circuit Malfunction 7B1-39. .
DTC P0715 Input / Turbine Speed
Sensor Circuit Malfunction 7B1-42. . . . . . . . . .
DTC P0720 Output Speed Sensor
Circuit Malfunction 7B1-44. . . . . . . . . . . . . . . . .
DTC P0741 TCC Solenoid Valve
Performance or Stuck Off 7B1-46. . . . . . . . . . .
DTC P0743 TCC Solenoid Electrical 7B1-47. .
DTC P0751 Shift Solenoid Valve-A (#1)
Performance or Stuck Off 7B1-49. . . . . . . . . . .
DTC P0756 Shift Solenoid Valve-B (#2)
Performance or Stuck Off 7B1-49. . . . . . . . . . .
SECTION 7B1
AUTOMATIC TRANSMISSION
(4 A
/
T)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
7B1-2 AUTOMATIC TRANSMISSION (4 A / T)
DTC P0753 Shift Solenoid-A (#1)
Electrical 7B1-50. . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0758 Shift Solenoid-B (#2)
Electrical 7B1-50. . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1875 4WD Low Switch Circuit
Malfunction 7B1-52. . . . . . . . . . . . . . . . . . . . . . .
Line Pressure Test 7B1-54. . . . . . . . . . . . . . . . . .
Stall Test 7B1-55. . . . . . . . . . . . . . . . . . . . . . . . . .
Road Test 7B1-56. . . . . . . . . . . . . . . . . . . . . . . . .
Manual Road Test 7B1-57. . . . . . . . . . . . . . . . . .
Time Lag Test 7B1-57. . . . . . . . . . . . . . . . . . . . . .
Engine Brake Test 7B1-58. . . . . . . . . . . . . . . . . .
ªPº Range Test 7B1-58. . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7B1-59 . . . . . . . . . . . . . . . .
MAINTENANCE SERVICE 7B1-59. . . . . . . . . . . .
Fluid Level 7B1-59. . . . . . . . . . . . . . . . . . . . . . . . .
Fluid Change 7B1-60. . . . . . . . . . . . . . . . . . . . . .
Oil Cooler Hoses 7B1-61. . . . . . . . . . . . . . . . . . .
A / T THROTTLE CABLE 7B1-61. . . . . . . . . . . . . . .
MANUAL SELECTOR ASSEMBLY 7B1-62. . . . .
SELECT CABLE 7B1-63. . . . . . . . . . . . . . . . . . . . . TRANSMISSION RANGE SWITCH 7B1-64. . . . .
A
/
T OUTPUT SPEED SENSOR 7B1-64. . . . . . . .
O / D CUT SWITCH 7B1-64. . . . . . . . . . . . . . . . . . .
SOLENOID VALVES 7B1-64. . . . . . . . . . . . . . . . . .
THROTTLE POSITION SENSOR 7B1-66. . . . . . .
POWER / NORMAL CHANGE SWITCH 7B1-66. .
OIL COOLER PIPES 7B1-67. . . . . . . . . . . . . . . . . .
BRAKE INTERLOCK SYSTEM 7B1-68. . . . . . . . .
Shift Lock Solenoid Control 7B1-68. . . . . . . . . .
Shift Lock Solenoid Control Operations 7B1-68
Shift Lock (Solenoid) Manual Release 7B1-69.
System Inspection 7B1-69. . . . . . . . . . . . . . . . . .
KEY INTERLOCK CABLE 7B1-71. . . . . . . . . . . . .
DISMOUNTING OF TRANSMISSION
(WITH TRANSFER IF EQUIPPED) 7B1-74. . . .
REMOUNTING 7B1-77. . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7B1-78 . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7B1-78 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7B1-79 . . . . . .
SPECIAL TOOLS7B1-79 . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
Gear Shift Diagram
TCC Lock-up Diagram
Throttle valve opening
Vehicle speedUpshift
Downshift
Throttle valve opening
Vehicle speedTCC ON
TCC OFF 3rd
gear
4th
gear(km / h)
(km / h)
AUTOMATIC TRANSMISSION (4 A / T) 7B1-15
Power Mode For H25 EngineUnit: km / h
(mile/h)
Shift
Throttle opening
1
22
33
44
33
22
1
Full throttle48
(30)99
(62)160
(99)150
(93)90
(56)41
(25)
Closed throttle16
(10)30
(19)45
(28)38
(24)24
(15)7
(4)

YH4
GRAND
VITARA
1. Malfunction indicator lamp (MIL)
2. Scan tool
3. DLC
7B1-18 AUTOMATIC TRANSMISSION (4 A / T)
[For Vehicle without Monitor Connector]
ON-BOARD DIAGNOSTIC SYSTEM
For automatic transmission control system, PCM (ECM) has follow-
ing functions. Refer to Section 6 / 6-1 for details.

When the ignition switch is turned ON with the engine at a stop,
malfunction indicator lamp (MIL) turns ON to check the bulb of the
MIL.

When PCM detects a malfunction in A / T control system (and / or
a malfunction which gives an adverse effect to vehicle emission)
while the engine is running, it makes the malfunction indicator
lamp in the meter cluster of the instrument panel turn ON and
stores the malfunction area in its memory. (If it detects that contin-
uously 3 driving cycles are normal after detecting a malfunction,
however, it makes MIL turn OFF although DTC stored in its
memory will remain.)

It is possible to communicate through DLC by using not only SU-
ZUKI scan tool (Tech-1) but also generic scan tool. (Diagnostic in-
formation can be accessed by using a scan tool.)
2 Driving Cycle Detection Logic
Refer to section 6 / 6-1 for details.
Pending DTC
Refer to section 6 / 6-1 for details.
Freeze Frame Data
Refer to section 6 / 6-1 for details.