2001 SUZUKI GRAND VITARA warning

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-59
DTC CONFIRMATION PROCEDURE
1) Connect scan tool to DLC with ignition switch OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data by using scan tool and start
engine.
3) Increase vehicle speed to 55 km/h (35 mph) or more.
4) Keep driving above vehicle speed for 2 min. or more (Change of vehicle speed is permitted in this step).
5) Stop vehicle, and run engine at idle speed for 1 min.
6) Check if pending DTC exists by using scan tool. If not, check if oxygen sensor monitoring test has completed
by using scan tool. If not in both of above checks (i.e., no pending DTC and oxygen sensor monitoring test
not completed), check vehicle condition (environmental) and repeat step 3) through 6).
TROUBLESHOOTING
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.
NOTE:
Check to make sure that following conditions are satisfied when using this “DTC CONFIRMATION
PROCEDURE”.
Intake air temp. : – 8°C (18°F) or higher
Engine coolant temp. : – 8 – 110°C (18 – 230°F)
Altitude (barometric pressure) : 2400 m, 8000 ft or less (560 mmHg (75 kPa) or more)
Step Action Yes No
1 Was “ENGINE DIAG. FLOW TABLE” performed? Go to Step 2. Go to “ENGINE
DIAG. FLOW
TABLE” in this sec-
tion.
2 HO2S-1 output voltage check :
1) Connect scan tool to DLC with ignition switch OFF.
2) Warm up engine to normal operating temperature and
keep it at 2000 r/min. for 60 sec.
3) Repeat racing engine (Repeat depressing accelerator
pedal 5 to 6 times continuously to enrich A/F mixture
and take foot off from pedal to enlean and check HO2S
output voltage displayed on scan tool. See Fig.
Is over 0.6 V and below 0.3 V indicated?Go to Step 4. Go to Step 3.
3 HO2S-1 check :
1) With ignition switch OFF, disconnect HO2S-1 connec-
tor.
2) Check for proper connection to HO2S-1 at each termi-
nal.
3) If OK, connect voltmeter “1” and “2” terminal of HO2S-1
connector.
4) Start engine and check voltmeter while repeating rac-
ing engine.
Is over 0.6 V and below 0.3 V indicated?“RED” or “GRY/
YEL” circuit open or
short.
If wire and connec-
tions are OK, sub-
stitute a known-
good ECM (PCM)
and recheck.Replace HO2S-1.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-63
DTC P0136 HO2S-2 (Bank 1) Circuit Malfunction
WIRING DIAGRAM
DTC DETECTING CONDITION AND TROUBLE AREA
DTC CONFIRMATION PROCEDURE
1. HO2S heater relay
2. ECM (PCM)
3. HO2S-2 (Bank-1)
DTC DETECTING CONDITION TROUBLE AREA
DTC will set when any one of following conditions is detected (2 driving
cycle detection logic).
• 4.5 V or more HO2S circuit voltage is detected when 5 V power is con-
nected to HO2S circuit in ECM (PCM).
• While running with A/F feed back, average output voltage during speci-
fied time is too high or too low.
or
• While running with A/F feed back, max output voltage during specified
time is lower than specified value or min. output voltage during speci-
fied time is higher than specified value.• HO2S-2 or its circuit
• Fuel system
•ECM (PCM)
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-65
DTC P0141 HO2S-2 (Bank 1) Heater Circuit Malfunction
WIRING DIAGRAM
Refer to DTC P0136.
DTC DETECTING CONDITION AND TROUBLE AREA
DTC CONFIRMATION PROCEDURE
1) Connect scan tool with ignition switch OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data in ECM memory by using scan
tool and start engine.
3) Increase vehicle speed to 50 – 60 km/h (30 – 40 mph).
4) Keep driving above vehicle speed for 5 min. (Change of vehicle speed is permitted in this step).
5) Stop vehicle and check if pending DTC exists by using scan tool. If not, check if oxygen sensor heater moni-
toring test has completed by using scan tool. If not in both of above checks (i.e., no pending DTC and oxy-
gen sensor heater monitoring test not completed), check vehicle conditions (environmental) and repeat
Steps 3) through 5).DTC DETECTING CONDITION TROUBLE AREA
Following condition is detected when HO2S-2 heater operates (2
driving cycle detection logic).
• Current of HO2S-2 heater is more than 11.4 A or less than 0.32 A,
or
• Voltage of HO2S-2 heater is more than 13.8 V or less than 8.7 V.HO2S-2 heater or its circuit
ECM (PCM)
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.
NOTE:
Check to make sure that following conditions are satisfied when using this “DTC CONFIRMATION
PROCEDURE”.
Intake air temp. : – 8°C (18°F) or higher
Engine coolant temp. : – 8 – 110°C (18 – 230°F)
Altitude (barometric pressure) : 2400 m, 8000 ft or less (560 mmHg (75 kPa) or more)

6-1-68 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
DTC CONFIRMATION PROCEDURE
1) Connect scan tool to DLC with ignition switch OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data by using scan tool and start
engine.
3) Increase vehicle speed to 55 km/h (35 mph) or more.
4) Keep driving above vehicle speed for 2 min. or more (Change of vehicle speed is permitted in this step).
5) Stop vehicle, and run engine at idle speed for 1 min.
6) Check if pending DTC exists by using scan tool. If not, check if oxygen sensor monitoring test has completed
by using scan tool. If not in both of above checks (i.e., no pending DTC and oxygen sensor monitoring test
not completed), check vehicle condition (environmental) and repeat step 3) through 6).
TROUBLESHOOTING
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.
NOTE:
Check to make sure that following conditions are satisfied when using this “DTC CONFIRMATION
PROCEDURE”.
Intake air temp. : – 8°C (18°F) or higher
Engine coolant temp. : – 8 – 110°C (18 – 230°F)
Altitude (barometric pressure) : 2400 m, 8000 ft or less (560 mmHg (75 kPa) or more)
Step Action Yes No
1 Was “ENGINE DIAG. FLOW TABLE” performed? Go to Step 2. Go to “ENGINE
DIAG. FLOW
TABLE” in this sec-
tion.
2 HO2S-1 output voltage check :
1) Connect scan tool to DLC with ignition switch OFF.
2) Warm up engine to normal operating temperature and
keep it at 2000 r/min. for 60 sec.
3) Repeat racing engine (Repeat depressing accelerator
pedal 5 to 6 times continuously to enrich A/F mixture
and take foot off from pedal to enlean and check HO2S
output voltage displayed on scan tool. See Fig.
Is over 0.6 V and below 0.3 V indicated?Go to Step 4. Go to Step 3.
3 HO2S-1 check :
1) With ignition switch OFF, disconnect HO2S-1 connec-
tor.
2) Check for proper connection to HO2S-1 at each termi-
nal.
3) If OK, connect voltmeter “1” and “2” terminal of HO2S-1
connector.
4) Start engine and check voltmeter while repeating rac-
ing engine.
Is over 0.6 V and below 0.3 V indicated?“RED/BLU” or
“GRY/YEL” circuit
open or short.
If wire and connec-
tions are OK, sub-
stitute a known-
good ECM (PCM)
and recheck.Replace HO2S-1.

6-1-72 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
DTC P0156 HO2S-2 (Bank 2) Circuit Malfunction
WIRING DIAGRAM
DTC DETECTING CONDITION AND TROUBLE AREA
DTC CONFIRMATION PROCEDURE
1. HO2S heater relay
2. ECM (PCM)
3. HO2S-2 (Bank-2)
DTC DETECTING CONDITION TROUBLE AREA
DTC will set when any one of following conditions is detected (2 driving
cycle detection logic).
• 4.5 V or more HO2S circuit voltage is detected when 5 V power is con-
nected to HO2S circuit in ECM (PCM).
• While running with A/F feed back, average output voltage during speci-
fied time is too high or too low.
or
• While running with A/F feed back, max output voltage during specified
time is lower than specified value or min. output voltage during speci-
fied time is higher than specified value.• HO2S-2 or its circuit
• Fuel system
• ECM (PCM)
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.

6-1-74 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
DTC P0161 HO2S-2 (Bank 2) Heater Circuit Malfunction
WIRING DIAGRAM
Refer to DTC P0156.
DTC DETECTING CONDITION AND TROUBLE AREA
DTC CONFIRMATION PROCEDURE
1) Connect scan tool with ignition switch OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data in ECM memory by using scan
tool and start engine.
3) Increase vehicle speed to 50 – 60 km/h (30 – 40 mph).
4) Keep driving above vehicle speed for 5 min. (Change of vehicle speed is permitted in this step).
5) Stop vehicle and check if pending DTC exists by using scan tool. If not, check if oxygen sensor heater moni-
toring test has completed by using scan tool. If not in both of above checks (i.e., no pending DTC and oxy-
gen sensor heater monitoring test not completed), check vehicle conditions (environmental) and repeat
Steps 3) through 5).DTC DETECTING CONDITION TROUBLE AREA
Following condition is detected when HO2S-2 heater operates (2
driving cycle detection logic).
• Current of HO2S-2 heater is more than 11.4 A or less than 0.32 A,
or
• Voltage of HO2S-2 heater is more than 13.8 V or less than 8.7 V.HO2S-2 heater or its circuit
ECM (PCM)
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.
NOTE:
Check to make sure that following conditions are satisfied when using this “DTC CONFIRMATION
PROCEDURE”.
Intake air temp. : – 8°C (18°F) or higher
Engine coolant temp. : – 8 – 110°C (18 – 230°F)
Altitude (barometric pressure) : 2400 m, 8000 ft or less (560 mmHg (75 kPa) or more)

6-1-76 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
DTC P0171/P0172 Fuel System Too Lean/Rich (Bank 1)
DTC DETECTING CONDITION AND POSSIBLE CAUSE
DTC CONFIRMATION PROCEDURE
1) Connect scan tool to DLC with ignition switch OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data by using scan tool and warm up
engine completely.
3) Increase vehicle speed to 50 – 60 km/h (30 – 40 mph).
4) Keep driving above vehicle speed for 3 min. or more.
5) Stop vehicle and check pending DTC by using scan tool.DTC DETECTING CONDITION TROUBLE AREA
When running after engine warmed (2 driving cycle
detection logic).
• Short term fuel trim exceeding 15 % or long term fuel
trim exceeding 20 % and total trim exceeding 43 % is
detected.
– Fuel system too lean
• Short term fuel trim less than – 11 % or long term fuel
trim less than – 11 % and total trim less than – 30 % is
detected.
– Fuel trim too rich• Vacuum leaks (air inhaling)
• Exhaust gas leakage
• Fuel pressure out of specification
• Heated oxygen sensor malfunction
• EGR system malfunction
• MAF sensor poor performance
• ECT sensor poor performance
• Fuel level sensor.
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.
NOTE:
Check to make sure that following conditions are satisfied when using this “DTC CONFIRMATION
PROCEDURE”.
Intake air temp. at start : – 8 – 60°C (18 – 140°F)
Engine coolant temp. at start : – 8 – 95°C (18 – 203°F)
Altitude (barometric pressure) : 2400 m, 8000 ft or less (560 mmHg (75 kPa) or more)
Intake air temp. : – 8°C (18°F) or higher
Engine coolant temp. : 110°C (230°F) or lower

6-1-78 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
DTC P0174/P0175 Fuel System Too Lean/Rich (Bank 2)
DTC DETECTING CONDITION AND POSSIBLE CAUSE
DTC CONFIRMATION PROCEDURE
1) Connect scan tool to DLC with ignition switch OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data by using scan tool and warm up
engine completely.
3) Increase vehicle speed to 50 – 60 km/h (30 – 40 mph).
4) Keep driving above vehicle speed for 3 min. or more.
5) Stop vehicle and check pending DTC by using scan tool.DTC DETECTING CONDITION TROUBLE AREA
When running after engine warmed (2 driving cycle
detection logic).
• Short term fuel trim exceeding 15 % or long term fuel
trim exceeding 20 % and total trim exceeding 43 % is
detected.
– Fuel system too lean
• Short term fuel trim less than – 11 % or long term fuel
trim less than – 11 % and total trim less than – 30 % is
detected.
– Fuel trim too rich• Vacuum leaks (air inhaling)
• Exhaust gas leakage
• Fuel pressure out of specification
• Heated oxygen sensor malfunction
• EGR system malfunction
• MAF sensor poor performance
• ECT sensor poor performance
• Fuel level sensor.
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.
NOTE:
Check to make sure that following conditions are satisfied when using this “DTC CONFIRMATION
PROCEDURE”.
Intake air temp. at start : – 8 – 60°C (18 – 140°F)
Engine coolant temp. at start : – 8 – 95°C (18 – 203°F)
Altitude (barometric pressure) : 2400 m, 8000 ft or less (560 mmHg (75 kPa) or more)
Intake air temp. : – 8°C (18°F) or higher
Engine coolant temp. : 110°C (230°F) or lower