2001 SUZUKI GRAND VITARA torque

3C1-12 AIR BAG STEERING WHEEL AND COLUMN
Take measurement “b” as shown in the figure. If it is shorter
than specified length, replace steering upper shaft assembly
with new one.
Steering upper shaft assembly length “b” :
419.0 ± 1.0 mm (16.50 ± 0.04 in.)
Tightening Torque Specification
“b”
Fastening partTightening torque
Nm kg-m lb-ft
Driver air bag (inflator) module bolt 9 0.9 6.5
Steering shaft nut 33 3.3 23.5
Steering column mounting bolt and nut 25 2.5 18.0
Steering shaft joint bolt 25 2.5 18.0
Steering lower shaft assembly lower joint bolt 25 2.5 18.0
Shift (key) interlock cable screw 2.2 0.22 1.6
Steering upper shaft mounting bolt 23 2.3 17.0
Steering upper shaft upper joint nut 23 2.3 17.0

FRONT SUSPENSION 3D-1
3D
SECTION 3D
FRONT SUSPENSION
CONTENTS
On-Vehicle Service......................................... 3D-1
Suspension Control Arm/Bushings .............. 3D-1Tightening Torque Specification .................. 3D-2

On-Vehicle Service
Suspension Control Arm/Bushings
INSTALLATION
For the details, refer to the same item of the same section in the
Service Manual mentioned in the FOREWORD of this manual
noting following point.
Install control arm to chassis.
Tighten suspension arm nuts to specified torque after lower-
ing hoist and vehicle in non-loaded condition.
Tightening torque
Front suspension arm nut (a) :
85 N·m (8.5 kg-m, 61.5 lb-ft)
Front suspension arm nut (b) :
100 N·m (10.0 kg-m, 72.5 lb-ft) CAUTION:
All front suspension fasteners are an important attaching part in that it could affect the performance
of vital parts and systems, and/or could result in major repair expense. They must be replaced with
one of the same part number or with an equivalent part if replacement becomes necessary. Do not
use a replacement part of lesser quality or substitute design. Torque values must be used as speci-
fied during reassembly to assure proper retention of this part.
Never attempt to heat, quench or straighten any front suspension part. Replace it with a new part or
damage to the part may result.
NOTE:
For the descriptions (items) not found in this section, refer to the same section of the Service Manual
mentioned in the FOREWORD of this manual.
NOTE:
Don’t reuse front suspension arm nut (b).
(b)

3D-2 FRONT SUSPENSION
Tightening Torque Specification

REAR SUSPENSION 3E-1
3E
SECTION 3E
REAR SUSPENSION
CONTENTS
On-Vehicle Service......................................... 3E-1
Rear Axle Shaft and Wheel Bearing ............ 3E-1
Rear Axle Shaft Inner Oil Seal ..................... 3E-5
Rear Axle Housing ....................................... 3E-5Tightening Torque Specification .................. 3E-6
Required Service Material ............................. 3E-6
Special Tool .................................................... 3E-7

On-Vehicle Service
Rear Axle Shaft and Wheel Bearing
REMOVAL
1) Remove axle shaft from axle housing according to Step1) to
6) in the same section in the service manual mentioned in
the FOREWORD of this manual noting following points. NOTE:
For the descriptions (items) not found in this section, refer to the same section of the Service Man-
ual mentioned in the FOREWORD of this manual.
All suspension fasteners are an important attaching part in that it could affect the performance of
vital parts and systems, and/or could result in major repair expense. They must be replaced with
one of the same part number or with an equivalent part if replacement becomes necessary. Do not
use a replacement part of lesser quality or substitute design. Torque values must be used as speci-
fied during reassembly to assure proper retention of this part.
Never attempt to heat, quench or straighten any suspension part. Replace it with a new part, or
damage to the part may result.

3E-4 REAR SUSPENSION
5) Apply grease “A” to axle shaft inner oil seal lip as shown in
the figure.
“A” : Grease 99000-25010
6) Apply water tight sealant “B” to mating surfaces of brake
back plate and rear axle hub (2).
“B” : Water tight sealant 99000-31110
7) Install rear axle shaft to rear axle housing and tighten bear-
ing retainer nuts to specified torque.
Rear axle shaft length “L”
Left side : 700.5 mm (27.6 in.)
Right side : 769.5 mm (30.3 in.)
Tightening torque
Bearing retainer nut (a) : 50 N·m (5.0 kg-m, 36.5 lb-ft)
8) Tighten wheel speed sensor bolt to specified torque (if
equipped with ABS).
Tightening torque
Wheel speed sensor bolt (b) : 21 N·m (2.1 kg-m, 15.5 lb-ft)
9) Refill rear axle housing with new specified gear oil.
Refer to “MAINTENANCE SERVICE” in Section 7F.
10) Install brake drum. Refer to “BRAKE DRUM” in Section 5C.
1. Axle housing
NOTE:
When installing rear axle shaft, be careful not to cause
damage to oil seal lip in axle housing.
(b)

REAR SUSPENSION 3E-5
Rear Axle Shaft Inner Oil Seal
INSTALLATION
1) Using special tool drive in oil seal until it contacts oil seal pro-
tector in axle housing.
Special tool
(A) : 09924-74510
(B) : 09944-88210
“A” : Grease 99000-25010
“B” : Sealant 99000-31110
2) For procedure hereafter, refer to steps 6) to 11) of “INSTAL-
LATION” under “REAR AXLE SHAFT” in the service manual
mentioned in the FOREWORD of this manual.
Rear Axle Housing
INSTALLATION
For Step 1) to 4), 7) and 9) to 30), refer to the same section in the
Service Manual mentioned in the FOREWORD of this manual.
3) Clean mating surfaces of axle housing (1) and differential
carrier and apply sealant “A” to housing side.
“A” : Sealant 99000-31110
4) Install differential carrier assembly to axle housing and
tighten carrier bolts to specified torque.
Tightening torque
Differential carrier bolt (a) :
55 N·m (5.5 kg-m, 40.0 lb-ft) NOTE:
Make sure that oil seal is free from inclination as it is
installed.
Refer to the figure so that oil seal is installed in proper
direction.
1. Hammer 4. Oil seal
2. Rod 5. Body center
3. Oil seal protector

3E-6 REAR SUSPENSION
5) Apply thread lock cement to thread of propeller shaft flange
bolt if reused. Install propeller shaft to joint flange aligning
match marks and torque flange nuts to specification.
“A” : Cement 99000-32110
Tightening torque
Propeller shaft nut (a) :
60 N·m (6.0 kg-m, 43.5 lb-ft)
Tightening Torque Specification
Required Service Material
Fastening partTightening torque
Nm kg-m lb-ft
Shock absorber nut 29 2.9 21.0
Shock absorber lower nut 85 8.5 61.5
Lower rod bolt and nut 100 10.0 72.5
Upper rod bolt and nut 100 10.0 72.5
Lateral rod bolt 100 10.0 72.5
Differential carrier bolt 55 5.5 40.0
Propeller shaft nut 60 6.0 43.5
Brake pipe flare nut 16 1.6 11.5
Bearing retainer nut 50 5.0 36.5
Differentiation gear oil filler & drain plug (filler plug) 50 5.0 36.5
Differentiation gear oil filler & drain plug (drain plug) 27 2.7 16.0
Wheel nut 100 10.0 72.5
Wheel speed sensor bolt 21 2.1 15.5
MaterialRecommended SUZUKI product
(Part Number)Use
Lithium grease SUZUKI SUPER GREASE A
(99000-25010)Oil seal lip
Brake fluid DOT 3Brake reservoir tank
Sealant SUZUKI BOND NO. 1215
(99000-31110)Joint seam of axle and brake back plate
Joint seam of bearing retainer and brake
back plate
Joint seam of differential carrier and axle
housing
Drain plug
Mating surface of oil seal and axle housing
Gear oil For gear oil information, refer to Section 7FDifferential gear (Rear axle housing)
Thread lock
cementTHREAD LOCK CEMENT SUPER 1322
(99000-32110)Rear propeller shaft flange bolts

WHEELS AND TIRES 3F-1
3F
SECTION 3F
WHEELS AND TIRES
CONTENTS
General Description ....................................... 3F-1
Tires ............................................................. 3F-1
Wheels ......................................................... 3F-1

General Description
Tires
This vehicle is equipped with following tire.
Tire specification :
P235/60 R16 or 235/60 R16
The tires are of tubeless type. The tires are designed to operate satisfactorily with loads up to the full rated load
capacity when inflated to the recommended inflation pressure.
Correct tire pressures and driving habits have an important influence on tire life. Heavy cornering, excessively
rapid acceleration, and unnecessary sharp braking increase tire wear.
Wheels
Standard equipment wheels are following steel wheels.
Wheel specification :
16 x 7 JJ NOTE:
For the descriptions (items) not found in this section, refer to the same section of the Service Man-
ual mentioned in the FOREWORD of this manual.
All wheel fasteners are important attaching parts in that they could affect the performance of vital
parts and systems, and/or could result in major repair expense. They must be replaced with one of
the same part number or with an equivalent part if replacement becomes necessary. Do not use a
replacement part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to assure proper retention of all parts.
There is to be no welding as it may result in extensive damage and weakening of the metal.