2001 SUZUKI GRAND VITARA ig meter

AIR BAG SYSTEM 10B-17
TABLE TEST DESCRIPTION
Table A :
STEP 1 : Check “AIR BAG” fuse.
STEP 2 : Check power source circuit.
STEP 3 : Check “AIR BAG” warning lamp circuit.
Table B :
STEP 1 : Check combination meter power feed circuit.
STEP 2 : Check electrical connection check mechanism in SDM connector.
STEP 3 : Check “AIR BAG” warning lamp circuit.
STEP 4 : Check open in “AIR BAG” warning lamp circuit.
STEP 5 : Check short from “AIR BAG” warning lamp circuit to power circuit.
STEP 6 : Check “AIR BAG” bulb.
Table C and D :
STEP 1 : Check “AIR BAG” monitor coupler.
STEP 2 : Check diagnosis switch circuit for air bag system.
DIAGNOSTIC FLOW TABLE
Table A :
[A] Fig. for STEP 2/[B] Fig. for STEP 3
Special tool
(A) : 09932-75020 Step Action Yes No
1 1) Ignition switch OFF.
2) Remove and inspect “AIR BAG” fuse.
Is fuse good?Go to step 2.“BLU/RED” wire short to
ground.
After repair, replace “AIR
BAG” fuse.
2 1) Disconnect SDM connector
2) Check proper connection to SDM at termi-
nal “Q01-4”.
3) If OK then check voltage between “Q01-4”
terminal of SDM connector and body
ground with ignition switch ON.
Is it 8 V or more?Go to step 3.“BLU/RED” wire (between
“AIR BAG” fuse and SDM
connector) open “BLU/
BLK” wire (between igni-
tion switch and “AIR BAG”
fuse) open or short to
ground
3 1) Disconnect 16-pin connector from combina-
tion meter. Refer to COMBINATION
METER in SECTION 8C.
2) Check resistance between “Q01-2” termi-
nal of SDM connector and body ground.
Is circuit open?Substitute a known-good
SDM and recheck.“BLU” wire (between com-
bination meter and SDM
connector) short to
ground

10B-18 AIR BAG SYSTEM
Table B :
NOTE:
Upon completion of inspection and repair work, perform following items.
Reconnect all air bag system components, ensure all components are properly mounted.
Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK to confirm that the trouble has been corrected.
Step Action Yes No
1 1) Set parking brake.
2) Note combination meter when ignition
switch is turned ON.
Does the “BRAKE” indicator (warning lamp)
come ON?Go to step 2.“BLK/BLU” wire, “BLK/
WHT” wire and “IG
METER” fuse (between
ignition switch and combi-
nation meter) open or
short to ground
2 1) With ignition switch OFF, disconnect SDM
connector.
2) Check electrical connection check mecha-
nism.
Is it in good condition?Go to step 3. Repair electrical connec-
tion check mechanism.
3 1) Disconnect SDM connector.
2) Check proper connection to SDM at termi-
nal “Q01-2”.
3) If OK then check voltage from “Q01-2” ter-
minal of SDM connector to body ground
with ignition switch ON.
Is it 8 V or more?Substitute a known-good
SDM and recheck.Go to step 4.
4 1) Remove combination meter. Refer to COM-
BINATION METER in SECTION 8.
2) Check proper connection to combination
meter at “BLU” terminal for “AIR BAG”
warning lamp and to SDM at terminal “Q01-
2”.
3) If OK then check resistance between “BLU”
wire terminal of combination meter connec-
tor (16-pin connector) and “Q01-2” terminal
of SDM connector.
Is circuit short?Go to step 5. Repair high resistance or
open in “BLU” wire circuit
(between combination
meter and SDM).
5 1) Measure voltage from “Q01-2” terminal of
SDM connector to body ground with ignition
switch ON.
Is it 8 V or more?Repair short from “BLU”
wire circuit (between com-
bination meter and SDM)
to power circuit.Go to step 6.
6 1) Remove and inspect “AIR BAG” bulb.
Is bulb good?Substitute a known-good
combination meter and
recheck.Replace bulb.

AIR BAG SYSTEM 10B-19
[A] Fig. for STEP 2/[B] Fig. for STEP 3 and 5/[C] Fig. for STEP 4
Special tool
(A) : 09932-75020
Table C :
Fig. for STEP 2
Special tool
(A) : 09932-75020
1. 16-pin connector (for combination meter)
2.“BLU” wire terminal
NOTE:
Upon completion of inspection and repair work, perform following items.
Reconnect all air bag system components, ensure all components are properly mounted.
Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK to confirm that the trouble has been corrected.
Step Action Yes No
1 1) Check “AIR BAG” monitor coupler.
Is it connected diagnosis switch terminal in “AIR
BAG” monitor coupler and body ground by ser-
vice wire?Remove service wire. Go to step 2.
2 1) With ignition switch OFF, disconnect SDM
connector.
2) Measure resistance between “Q01-15” ter-
minal of SDM connector and body ground.
Is circuit open?Substitute a known-good
SDM and recheck.Repair short from “PPL”
wire circuit to ground.
NOTE:
Upon completion of inspection and repair work, perform following items.
Reconnect all air bag system components, ensure all components are properly mounted.
Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK to confirm that the trouble has been corrected.

AIR BAG SYSTEM 10B-21
Table E - SDM Cannot Communicate through The Serial Data Circuit
WIRING DIAGRAM
TABLE TEST DESCRIPTION
STEP 1 : An improper connection to the data link connector (DLC) will prevent communications from being
established.
STEP 2 : This test checks whether it is possible to communicate with other control module.
STEP 3 : This test checks for an open in “PPL/RED” circuit (in air bag harness).
[A]: Air bag harness 5.“AIR BAG” fuse 10.“AIR BAG” monitor coupler
1. From main fuse 6. Connection detection pin 11. Ground for air bag system
2. Ignition switch 7. SDM 12. Ground on body
3.“IG METER” fuse 8. DLC 13. Ground on Engine block
4.“AIR BAG” warning lamp in combination lamp 9. To ECM, TCM (if equipped) and ABS con-
trol module (if equipped)14. Immobilizer control module (if equipped)
14
1PPL/WHT
BLK
BLK/YEL WHT
10
11
PPL
BLK
“Q04”Q01-15
Q01-17DNS
GND7
[A]5V
812
13
1
2
34 BLK/BLUBLU/BLK BLU/RED
BLK/WHT BLK/WHTBLUBLU
6
PPL/REDPPL/RED
9
Q01-2
Q01-20L1
L2
SDLLA
Q01-4
IG
12V
“G27”
“Q02”
5
CAUTION:
Be sure to perform AIR BAG DIAGNOSTIC SYSTEM CHECK before starting diagnosis according to
flow table.
When measurement of resistance or voltage is required in this table, use a tester along with a cor-
rect terminal adapter from special tool (Connector test adapter kit).
When a check for proper connection is required, refer to INTERMITTENT AND POOR CONNEC-
TIONS in this section.
If there is open circuit in the air bag wire harness, connector or terminal is found damaged, replace
the wire harness, connector and terminal as an assembly.

AIR BAG SYSTEM 10B-47
DTC B1061 – “AIR BAG” Warning Lamp Circuit Failure
WIRING DIAGRAM
DTC WILL SET WHEN:
The voltage at the “AIR BAG” warning lamp circuit terminal “Q01-2” does not match the commanded state of the
warning lamp driver for specified time.2 1) Inspect front of vehicle and undercar-
riage for signs of impact.
Are there signs of impact?Replace components and
perform inspections as
directed in REPAIRS AND
INSPECTIONS
REQUIRED AFTER AN
ACCIDENT in this section.Substitute a known-good
SDM and recheck. Step Action Yes No
NOTE:
Upon completion of inspection and repair work, perform following items.
Reconnect all air bag system components, ensure all components are properly mounted.
Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK to confirm that the trouble has been corrected.
1. From main fuse 5.“AIR BAG” fuse 9. To ECM, TCM (if equipped) and ABS control
module (if equipped)
2. Ignition switch 6. Connection detection pin 10.“AIR BAG” monitor coupler
3.“IG METER” fuse 7. SDM 11. Ground for air bag system
4.“AIR BAG” warning lamp in combination meter 8. To DLC [A]: Air bag harness
1
2
34 BLK/BLUBLU/BLK BLU/RED
BLK/WHT BLK/WHTBLUBLU
6
PPL/REDPPL/RED
8
9
10
11
PPL
BLK
“Q04”
“Q01”
Q01-2
Q01-20
Q01-15
Q01-17L1
L2
SDL
DNS
GNDLA
Q01-4
IG
7
[A]
12V
5V
“G27”“Q02”
5
CAUTION:
Be sure to perform AIR BAG DIAGNOSTIC SYSTEM CHECK before starting diagnosis according to
flow table.
When measurement of resistance or voltage is required in this table, use a tester along with a cor-
rect terminal adapter from special tool (Connector test adapter kit).
When a check for proper connection is required, refer to INTERMITTENT AND POOR CONNEC-
TIONS in this section.
If there is open circuit in the air bag wire harness, connector or terminal is found damaged, replace
the wire harness, connector and terminal as an assembly.

AIR BAG SYSTEM 10B-67
5) Set air bag (inflator) module or seat belt pretensioner as fol-
lows.
[In case of driver air bag (inflator) module]
a) Clear a space on the ground about 185 cm (6 ft) (3) in
diameter where the driver air bag (inflator) module (1) is to
be deployed. A paved, outdoor location where there is no
activity is preferred. If an outdoor location is not available, a
space on the shop floor where there is no activity and suffi-
cient ventilation is recommended.
Ensure no loose or flammable objects are within the
deployment area.
b) Place the driver air bag (inflator) module (1), with its vinyl
trim cover facing up (2), on the ground in the space just
cleared.
[In case of passenger air bag (inflator) module]
a) Clear a space on the ground about 185 cm (6 ft) (2) in
diameter where the fixture (special tool) with attached air
bag (inflator) module (1) is to be placed for deployment. A
paved outdoor location where there is no activity is pre-
ferred. If an outdoor location is not available, a space on the
shop floor where there is no activity and sufficient ventila-
tion is recommended. Ensure that no loose or flammable
objects are within the deployment area.
b) Place special tool (passenger air bag (inflator) module
deployment fixture) on the ground in the space cleared in
step a), if it has not already been placed there.
Special tool
(B) : 09932-75041 WARNING:
For handing and storage of a live seat belt preten-
sioner, select a place where the ambient temperature
below 65°
°° °C (150°
°° °F), without high humidity and away
from electric noise.
Never carry the seat belt pretensioner by the wire or
connector of the pretensioner.
When placing a live seat belt pretensioner on the work-
bench or other surface, be sure not to lay it with its
exhaust hole (1) provided side facing down. It is also
prohibited to put something on its face with an exhaust
hole (1) or to put a seat belt pretensioner on top of
another.
Otherwise, personal injury may result.

10B-68 AIR BAG SYSTEM
c) Fill plastic reservoir in fixture (special tool) with water or
sand. This is necessary to provide sufficient stabilization of
the fixture during deployment.
d) Attach the passenger air bag (inflator) module in the fixture
(special tool) using mounting attachment, hold-down bolts
and nuts and M8 bolts and nuts (1).
Securely hand-tighten all fastener prior to deployment.
[In case of seat belt pretensioner]
a) Pull out the webbing (2) fully as shown in the figure and cut
it at the root of the pretensioner (retractor assembly) (1) as
shown in the figure.
b) Clear a space on the ground about 185 cm (6 ft) (4) in
diameter where the seat belt pretensioner (retractor assem-
bly) (1) is to be activated. A paved, outdoor location where
there is no activity is preferred. If an outdoor location is not
available, a space on the shop floor where there is no activ-
ity and sufficient ventilation is recommended.
Ensure no loose or flammable objects are within the activa-
tion area.
c) Place the seat belt pretensioner (retractor assembly) (1) as
shown in the figure on the ground in the space just cleared. CAUTION:
Be sure to use the following bolt and nut for fixing
passenger air bag (inflator) module to mounting
attachment.
Size : M8, Strength : 7T
WARNING:
As the drum (3) of the retractor assembly (1) turns very
quickly as soon as the webbing (2) is cut, fix the retractor
assembly (1) with a vise on the workbench and keep your
hands and fingers away from it when cutting the webbing
(2).

AIR BAG SYSTEM 10B-77
Tightening Torque Specification
Special Tool
Fastening partTightening torque
Nm kg-m lb-ft
SDM bolt 6 0.6 4.5
Passenger air bag (inflator) module screw 5.5 0.55 4.0
Passenger air bag (inflator) module bolt 23 2.3 16.5
Forward sensor bolt 10 1.0 7.2
Driver air bag (inflator) module bolt Refer to Section 3C1.
Seat belt pretensioner (retractor assembly) bolt Refer to Section 10A.
09932-75010 09932-75030 09932-75041 09932-75020
Air bag driver/passenger
load toolAir bag deployment har-
nessPassenger air bag (infla-
tor) module deployment
fixtureConnector test adapter kit
09931-76030 09931-76011
Digital multimeter
(See NOTE “B” and
WARNING.)16/14 pin DLC cable for
Tech-1ATech-1A kit (SUZUKI scan
tool)
(See NOTE “A”.)Mass storage cartridge for
Tech-1A
Tech-2 kit (SUZUKI scan
tool) (See NOTE “C”.)