2001 SUBARU FORESTER lights

Audio5-35
–
CONTINUED –

To insert a disc
1. Press one of the “Disc select ” buttons 3 (numbered from 1 to 6)
for which the disc indicator light 2 is “OFF”.
The Disc indicator lights are located directly above the corresponding “ Disc select ” buttons.
2. The indicator will begin blinking. The blinking will last for 15 se-conds.
During this period, insert a desired disc, and the disc will begin to
play. (If any disc is not inserted during this period, the “Disc slot ”
1
door will close. Repeat step 1.)
Be sure to hold a disc with the label side (the side where titles areprinted) up.
3. To insert another disc, repeat step 1 and 2 choosing a differentdisc select button. To insert six discs at a time
1. Press and hold the “Disc select ” button number 1 until all disc indi-
cators begin blinking (about 1.5 seconds).
2. The indicators will blink for 15 seconds. During this period, insert
desired six discs.
3. When all discs are loaded, the first disc will begin to play. (If no
disc is inserted within this 15 seconds, the entire disc load sequencewill be canceled.) To remove a disc
1. Press the desired one of the “Disc select ” buttons
3 (numbered
from 1 to 6) for which the disc indicator light is on.
2. Press the “Eject button ”
4 . The selected disc will be ejected and
the indicator light will begin blinking.
3. To remove another disc, repeat step 1 and 2 choosing a different“ Disc select ” button.
(To remove discs when the ignition switch is in the “Lock” position,
press the “Eject” button, and the first disc will be ejected. Press the
“Eject” button again, and the next disc will be ejected and so on. At
this time, the “Disc select ” buttons are disabled.)

7-6NOTE If the fuel filler cap is not tightened until it clicks or if the tether is caught under the cap, the CHECK ENGINE warning light maycome on. Refer to the
“Warning and indicator lights ” section
located in chapter 3.
State emission testing (U.S. only)
WARNING
Testing of an All-Wheel Drive vehicle must NEVER be performed
on a single two-wheel dynamometer. Attempting to do so willresult in uncontrolled vehicle movement and may cause an acci-
dent or injuries to persons nearby.
CAUTION
Resultant vehicle damage due to improper testing is not covered
under the SUBARU Limited Warranty and is the responsibility ofthe state inspection program or its contractors or licensees.
At state inspection time, remember to tell your inspection or service
station in advance not to place your Subaru AWD vehicle on a two-
wheel dynamometer. Otherwise, serious transmission damage willresult.
Some states have started using d ynamometers in thei r state insp ec tion
p rog rams in ord er to meet their ob lig ation und er fe d eral law to imp lement
stric ter vehic le emission stand ard s to red uc e air p ollution from c ars. A
d ynamometer is a tread mill or roller-like testing d evic e that allows your
c ar ’s wheels to turn while the c ar remains in one p lac e . Dep end ing on
the severity of a state ’s air p ollution p rob lems, the states must ad op t
either a “b asic ” or “enhanc ed ” vehic le emission insp ec tion test. Nor-
mally, a p ortion of the b asic emission test c onsist s of an emission
insp ec tor inserting an analyzer p rob e into the exha ust p ip e of an id ling
vehic le for a short p eriod of time. States with mor e severe air p ollution
p rob lems are req uired to ad op t an enhanc ed vehic le emission test. This

Starting and operating8-29
–
CONTINUED –
c ient slac k in the c hains taking tig ht-turn situati
ons into ac c ount; how-
ever, b e c areful not to let them d rag on the g round .
For more information ab out the safety c hain c onnec t ion, refer to the
instruc tions for your hitc h and trailer. n Side mirrors
After hitc hing a trailer to your vehic le, c hec k tha t the stand ard sid e
mirrors p rovid e a g ood rearward field of view witho ut sig nific ant b lind
sp ots. If sig nific ant b lind sp ots oc c ur with the ve hic le’s stand ard sid e
mirrors, use towing mirrors that c onform with Fed er al, state/p rovinc e
and /or other ap p lic ab le reg ulations.
HS0146
n Trailer lights CAUTION
Direct splicing or other improper connection of trailer lights may
damage your vehicle ’s electrical system and cause a malfunction
of your vehicle ’s lighting system.
Connec tion of trailer lig hts to your vehic le ’s elec tric al system req uires
mod ific ations to the vehic le ’s lig hting c irc uit to inc rease its c ap ac ity
and ac c ommod ate wiring c hang es. To ensure the trail er lig hts are
c onnec ted p rop erly, p lease c onsult your SUBARU d eal er. Chec k for
p rop er op eration of the turn sig nals and the b rake lig hts and p arking
lig hts eac h time you hitc h up .

11-2Headlight
11-49
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fog light (if equipped) 11-50
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front turn signal, parking light and front side marker light 11-51 . . . . .
Rear combination lights 11-52
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
License plate light 11-53
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior light and luggage compartment light 11-54 . . . . . . . . . . . . . . . . . . . . . .
Spot light 11-55
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High mount stop light 11-55
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11-52the fend er.
3. Remove the b ulb hold er from the front turn sig nal
lig ht assemb ly b y
turning it c ounterc loc kwise.
4. Pull the b ulb out of the soc ket. Install a new b u lb .
5. Set the b ulb hold er into the front turn sig nal li g ht assemb ly and turn it
c loc kwise until it loc ks.
6. Set the front turn sig nal lig ht assemb ly into the fend er. Tig hten the
mounting sc rew. Rear combination lights Brake/tail and rear turn signal light
HS0219
HS0218
1. Unlatc h the rear c omb ination lig ht c over b y p ulli ng the knob . Op en
the c over up .
2. Remove the b ulb hold er from the rear c omb ination lig ht assemb ly
b y turning it c ounterc loc kwise.
3. Remove the b ulb from the soc ket b y p ushing it and turning c oun-
terc loc kwise. Install a new b ulb .
4. Set the b ulb hold er into the rear c omb ination lig ht assemb ly and
turn it c loc kwise until it loc ks.
5. Close the c over and latc h the loc k.