2001 SUBARU FORESTER pressure

11-4
Always use the proper tools and make certain that they are
well maintained. Never get under the vehicle supported only by a jack. Always
use a safety stand to support the vehicle. Never keep the engine running in a poorly ventilated area,
such as a garage or other closed areas. Do not smoke or allow open flames around the fuel or battery.
This will cause a fire. Wear adequate eye protection to guard against getting oil or
other fluids in your eyes. If something does get in your eyes,
thoroughly wash it out with clean water. Because the fuel system is under pressure, replacement of the
fuel filter should be performed only by your SUBARU dealer. The SRS airbag has no user-serviceable parts. Tampering with
or disconnecting the system ’s wiring could result in accidental
inflation of the airbag or could make the system inoperative,
which may result in serious injury. The wiring harnesses of theSRS airbag system are covered with yellow insulation and the
connectors of the system are yellow, for easy identification. Donot use electrical test equipment on any circuit related to the SRSairbag system. For required servicing of the SRS airbag, see your
nearest SUBARU dealer. Before checking or servicing in the engine compartment
Always stop the engine and set the parking brake firmly to pre-
vent the vehicle from moving. Always let the engine cool down. Engine parts become very
hot when the engine is running and remain hot for some time af-ter the engine is stopped. Do not spill engine oil, engine coolant, brake fluid or any other
fluid on hot engine components. This may cause a fire. Always remove the key from the ignition switch. When the
ignition switch is in the “ON” position, the cooling fan may oper-
ate suddenly even when the engine is stopped.

11-14Cooling system
WARNING
Never attempt to remove the radiator cap until the engine has
been shut off and has cooled down completely. Since the coolantis under pressure, you may suffer serious burns from a spray ofboiling hot coolant when the cap is removed.
CAUTION
The cooling system has been filled at the factory with a high
quality, corrosion-inhibiting, year-around coolant which providesprotection against freezing down to –33°F ( –36 °C). For adding,
use genuine SUBARU coolant or an equivalent: a mixture of 50%
soft water and 50% ethylene-glycol basis coolant. Use of improp-er coolants may result in corrosion in the cooling system. It is im-portant to maintain protection against freezing and corrosion,
even if freezing temperatures are not expected. Never mix differ-ent kinds of coolant. Do not splash the engine coolant over painted parts. The alco-
hol contained in the engine coolant may damage the paint sur-face.
Hose and connections
Your vehic le emp loys an elec tric c ooling fan whic h is thermostatic ally
c ontrolled to op erate when the eng ine c oolant reac h es a sp ec ific tem-
p erature.
If the rad iator c ooling fan d oes not op erate even w hen the eng ine
c oolant temp erature g aug e exc eed s the normal op erat ing rang e, the
c ooling fan c irc uit may b e d efec tive. Chec k the fus e and rep lac e it if
nec essary. If the fuse is not b lown, have the c ooli ng system c hec ked
b y your SUBARU d ealer.
If freq uent ad d ition of c oolant is nec essary, there may b e a leak in the
eng ine c ooling system. It is rec ommend ed that the c ooling system
and c onnec tions b e c hec ked for leaks, d amag e, or lo oseness.

11-16
Changing the coolant
WARNING
Never attempt to remove the radiator cap until the engine has
been shut off and has cooled down completely. Since the coolantis under pressure, you may suffer serious burns from a spray ofboiling hot coolant when the cap is removed.
Chang e the eng ine c oolant in the following p roc ed ur es ac c ord ing to
the maintenanc e sc hed ule in the “Warranty and Maintenanc e Book-
let ”.
1. Remove the und er c over.
2. Plac e a p rop er c ontainer und er the d rain p lug and loosen the d rain
p lug .
HSA002BB
HSA001BB
3. Loosen the rad iator c ap to d rain the c oolant from the rad iator. Then
d rain the c oolant from the reserve tank. Tig hten th e d rain p lug sec ure-
ly.
4. Install the und er c over.

Maintenance and service11-41
–
CONTINUED –
HS0199
7 to 8 notches
Tires and wheels WARNING
When replacing a tire, make sure you use only the same size,
circumferece, construction, brand, and load range as the original tires listed on the tire placard. Using other sizes, circumferecesor construction may result in severe mechanical damage to thedrivetrain of your vehicle and may affect ride, handling, braking,
speedometer/odometer calibration, and clearance between thebody and tires. It also may be dangerous and lead to loss of ve-hicle control. Do not use a combination of radial, belted bias or bias tires
since it may cause dangerous handling characteristics and leadto an accident. Do not let air out of warm tires to adjust pressure. Doing so
will result in low tire pressure.
The tires should b e c hec ked freq uently for p rop er t ire p ressure, wear,
and c uts. Tire pressure
For the b est b alanc e b etween fuel ec onomy, tire lif e, rid e c omfort, and
hand ling , tire p ressure should b e maintained in ac c ord anc e with sp ec ifi-

11-42c ations. Chec k the tire p ressure when the tires are
c old . Cold means that
the vehic le has b een p arked for three hours or has b een d riven less than
1 mile (1.6 km).
HS0251
The rec ommend ed tire p ressure and sizes are p rovid e d on the tire p lac -
ard , whic h is loc ated und er the d oor latc h on the d river’s sid e.
Adjusting the tire pressure
The tire p lac ard shows the rec ommend ed tire p ressur es at lig ht load ,
at full load and when towing a trailer. If the vehi c le is load ed with three
oc c up ants or less, ad just the tire p ressure to the level rec ommend ed
for lig ht load . If the vehic le is more load ed , ad ju st it to the level rec om-
mend ed for full load . When towing a trailer, ad just it to the level rec -
ommend ed for that op eration.
Tire rotation
Tire wear will vary with eac h wheel. To inc rease th e life of tires and keep
wear uniform, it is b est to rotate them every 7,500 miles (12,500 km).
When rotating tires, rep lac e any unevenly worn or d amag ed tire. After
rotating the tires, ad just tire p ressure and b e sur e to c hec k wheel nut
tig htness.

Specifications12-3
–
CONTINUED –

Capacities
Fuel tank 15.9 US g al (60 liter, 13.2 Imp g al)
Eng ine oil 4.2 US q t (4.0 liter, 3.5 Imp q t)
Manual transmission oil 3.7 US q t (3.5 liter, 3.1 Im p q t)
Automatic transmission fluid 9.8 US q t (9.3 liter, 8.2 Imp q t)
AT d ifferential g ear oil 1.3 US q t (1.2 liter, 1.1 I mp q t)
AWD rear d ifferential g ear oil 0.8 US q t (0.8 liter, 0.7 Imp q t)
Power steering fluid 0.7 US q t (0.7 liter, 0.6 Imp q t)
Eng ine c oolant 6.6 US q t (6.2 liter, 5.5 Imp q t)
Tires
Typ e Steel b elted rad ial, Tub eless
Size P205/70 R15 95S
P215/60 R16 94H
Pressure Front
(lig ht load ) 29 p si (200 kPa, 2.0 kg /c m 2
)
(full load ) 29 p si (200 kPa, 2.0 kg /c m 2
)
Rear
(lig ht load ) 28 p si (190 kPa, 1.9 kg /c m 2
)
(full load ) 36 p si (250 kPa, 2.5 kg /c m 2
)
Trailer towing Front 29 p si (200 kPa, 2.0 kg /c m 2
)
Rear 41 p si (280 kPa, 2.8 kg /c m 2
)
Wheel size 15 x 6J, 16 x 6 1
/2 JJ
Wheel alignment
Toe Front 0 0.12 in. (0 3 mm)
Rear 0.04 – 0.16 in. (1 – 4 mm)
Camb er Front –0 °15 ’
Rear –0 °35 ’

12-8Vehicle identification
HS0226
Vehicle identification number
Emission
control label
Vehicle identification number plate
Tire inflation pressure label
Model number plate Bar cord label
Vacuum hose piping label
Certification plate