2001 SUBARU FORESTER ESP

4-6

Heater operation Defrosting or defogging the windshield
HS0072
To d irec t warm air to the wind shield and front d oor wind ows:
1. Set the air inlet selec tion lever to the “
” p osition.
2. Set the air flow c ontrol d ial to the “
” p osition.
3. Turn the temp erature c ontrol d ial all the way to the rig ht.
4. Set the fan sp eed c ontrol lever to the hig hest sp eed .
NOTE
Warm air also comes out from the right and left air outlets. To
stop warm air flow from these outlets, turn the correspondingthumb-wheel to the “
” position.

Climate control4-7
–
CONTINUED –

Heating and defrosting
HS0074
To d irec t warm air toward the floor and the wind shi eld :
1. Set the air inlet selec tion lever to the “
” p osition.
2. Set the air flow c ontrol d ial to the “
” p osition.
3. Set the temp erature c ontrol d ial to the most c omf ortab le level.
4. Set the fan sp eed c ontrol lever to the d esired sp eed .
NOTE
Warm air also comes out from the right and left air outlets. To
stop warm air flow from these outlets, turn the correspondingthumb-wheel to the “
” position.
Heating
HS0076
To d irec t warm air toward the floor:

4-81. Set the air inlet selec tion lever to the
“
” p osition
2. Set the air flow c ontrol d ial to the “
” p osition.
3. Set the temp erature c ontrol d ial to the most c omf ortab le level.
4. Set the fan sp eed c ontrol lever to the d esired sp eed .
NOTE
Warm air also comes out from the right and left air outlets. To
stop warm air flow from these outlets, turn the correspondingthumb-wheel to the “
” position.
Bi-level heating
HS0078
This setting allows you to d irec t air of d ifferent temp eratures from the
instrument p anel and foot outlets. The air from the foot outlets is
slig htly warmer than from the instrument p anel outl ets.
1. Set the air inlet selec tion lever to the “
” p osition.
2. Set the air flow c ontrol d ial to the “
” p osition.
3. Set the temp erature c ontrol d ial to the d esired t emp erature level.
4. Set the fan sp eed c ontrol lever to the d esired sp eed .
Setting the temp erature c ontrol d ial fully turned t o the red area or b lue
area d ec reases the temp erature d ifferenc e b etween t he air from the
instrument p anel outlets and the air from the foot outlets.

4-14
HS4004BB
3. Insert the front filter assemb ly in the c ooling unit, then install the
rear filter assemb ly. NOTE Hold the filter tabs to facilitate installation.
The passenger compartment side of each filter is marked with
arrows (indicating “UP” and the direction of air flow). Ensure the
arrows point in the correct directions. Ensure each filter assembly ’s tongues and grooves fit the cor-
responding cooling unit and matching filter tongues and grooves.
HS4005BB
4. Reinstall the c over and sec ure it using the c lip s .
NOTE
Ensure no air leaks from the cooling unit through the cover.

Audio5-25
–
CONTINUED –

How to insert a CD(s)
n Inserting a CD
1. Press “LOAD” button O. If the magazine in the player has an idle
position where you can insert a disc, the “DISC” indicator associated
with the idle position will blink.
If no indicator blinks, it means that there is no idle position in the mag-azine.
2. As soon as the “DISC” indicator begins to blink, the “IN” will ap-
pear on display for a period of 15 seconds. Insert a disc during theperiod. The disc will be then automatically drawn in, and the playerwill begin to play back the first number of the disc. To insert more discs in succession, repeat Steps 1 and 2. The
magazine will be loaded with discs in the ascending order of position
number.
If you do not insert any disc in 15 seconds after you have pressed the
“LOAD” button, the player will begin to play back the first number of
the last disc you have inserted. The disc indicator steadily lights up if a disc is already inserted in
the corresponding position of the magazine. While the player is in the loading mode, if you press any of the oth-
er mode buttons “FM”
2, “AM” 1 and “TAPE” E, the player will enter
the standby mode. Press the “CD” button S to start playback.
n Inserting a disc in a desired position
1. Press the “LOAD” button. If the magazine in the player has an idle
position where you can insert a disc, the “DISC” indicator associated
with the idle position will blink.The positions in the magazine the indicator of which steadily lights up
are already loaded with discs.
2. Press the “DISC SELECT ” button
J at the position where you want
to insert a disc. The associated “DISC” indicator will blink, and the
“IN” will be displayed.
3. If you insert a disc during the 15-second period while the “IN” is on
display, the disc will be automatically drawn in, and the player will
start playback of the disc, beginning with the first number. To insert more discs in succession, repeat Steps 1 and 2.

Audio5-35
–
CONTINUED –

To insert a disc
1. Press one of the “Disc select ” buttons 3 (numbered from 1 to 6)
for which the disc indicator light 2 is “OFF”.
The Disc indicator lights are located directly above the corresponding “ Disc select ” buttons.
2. The indicator will begin blinking. The blinking will last for 15 se-conds.
During this period, insert a desired disc, and the disc will begin to
play. (If any disc is not inserted during this period, the “Disc slot ”
1
door will close. Repeat step 1.)
Be sure to hold a disc with the label side (the side where titles areprinted) up.
3. To insert another disc, repeat step 1 and 2 choosing a differentdisc select button. To insert six discs at a time
1. Press and hold the “Disc select ” button number 1 until all disc indi-
cators begin blinking (about 1.5 seconds).
2. The indicators will blink for 15 seconds. During this period, insert
desired six discs.
3. When all discs are loaded, the first disc will begin to play. (If no
disc is inserted within this 15 seconds, the entire disc load sequencewill be canceled.) To remove a disc
1. Press the desired one of the “Disc select ” buttons
3 (numbered
from 1 to 6) for which the disc indicator light is on.
2. Press the “Eject button ”
4 . The selected disc will be ejected and
the indicator light will begin blinking.
3. To remove another disc, repeat step 1 and 2 choosing a different“ Disc select ” button.
(To remove discs when the ignition switch is in the “Lock” position,
press the “Eject” button, and the first disc will be ejected. Press the
“Eject” button again, and the next disc will be ejected and so on. At
this time, the “Disc select ” buttons are disabled.)

5-36
To remove all discs at one time
1. Press and hold the “Eject” button 4 until all “Disc” indicators begin
blinking (about 1.5 seconds), and the first disc will be ejected.
2. When the disc is removed, the next one will be ejected, and so on. To replace a playing disc with another
Simply press the desired one of “Disc select ” buttons
3 (numbered
from 1 to 6) or press the “DISC UP ” or “DISC DOWN ” button on the
radio unit to select the desired disc, and the disc will begin to play. Disc indicators
Lit: when the corresponding storage tray is occupied by a disc. Blinking: Disc player is either in loading, eject or changing mode.OFF: No disc is loaded or the ignition switch is in the “LOCK” position.
Function control
Refer to CD player control operating instructions described in the“ Type P119 and P120 audio sets ” or “Type P121 audio set ” section.

Interior equipment6-9
–
CONTINUED –

Accessory power socket in the luggage compartment and dual power socket (if equipped) CAUTION
Do not attempt to use a cigarette lighter in the accessory
socket or dual power socket. Do not place any foreign objects, especially metal ones such
as coins or aluminum foil, into the accessory socket or dualpower socket. That could cause a short circuit. Always put thecap on the accessory socket and dual power socket when it isnot in use. Use only electrical appliances which are designed for 12V DC
and which consume less than 120W. Overloading the accessory
socket or dual power socket can cause a short circuit. Do not usedouble adapters or more than one electrical appliance. If the plug on your electric appliance is either too loose or too
tight for the accessory socket or dual power socket, this canresult in a poor contact or cause the plug to get stuck. Only use
plugs that fit properly. Use of an electric appliance in the accessory socket or dual
power socket for a long period of time while the engine is notrunning can cause battery discharge. Before driving your vehicle, make sure that the plug and the
cord on your electrical appliance will not interfere with your shift-ing gears and operating the accelerator and brake pedals. If theydo, do not use the electrical appliance while driving.