2001 Oldsmobile Intrigue key

2-8
Programmable Modes
Mode 1: Cancel the last door closed locking by
pressing the unlock switch or by fully inserting the
key in the ignition.
Mode 2: Override the last door closed locking feature
and lock the doors immediately by pressing the lock
switch a second time.
Mode 3: Let the last door closed locking feature
complete the locking of the vehicle.
When your vehicle was shipped from the factory,
it was programmed to Mode 3. The mode to which
your vehicle was programmed may have been changed
since it left the factory. To determine the mode to which
your vehicle is programmed or to program your vehicle
to a different mode, do the following:
1. Close all doors and turn the ignition switch to ON.
2. Press and hold the power door lock switch in the
unlock position.3. While holding the door unlock switch, cycle the
transaxle out of and back into PARK (P). Count the
number of chimes you hear. The number of chimes
tells you which mode your vehicle is set for. (If you
do not wish to change the current mode, you can
either exit the programming mode by following the
instructions listed here or program the next feature
available on your vehicle).
4. A single chime will be heard if the last door closed
locking feature is disabled, and two chimes will be
heard if the feature is enabled. After the initial
transaxle cycle, each additional cycle will turn
the last door closed locking feature on or off.
5. When the door unlock switch is released, the vehicle
will remain in the most recent operating mode.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
above or program the next feature available on
your vehicle.
Disconnecting the battery for up to a year will not
change any previously programmed modes.

2-9 Programmable Automatic Door Locks
Programmable automatic door locks is a standard
feature intended to provide enhanced security and
convenience by automatically locking and unlocking
vehicle doors. The automatic locking and unlocking of
the vehicle will occur if the ignition key is in ON and
the driver's door is closed when the vehicle is shifted
out of PARK (P).
Programmable Modes
Mode 1: No automatic door lock or unlock.
Mode 2: Automatic all door lock when the transaxle is
shifted out of PARK (P). No automatic door unlock.
Mode 3: Automatic all door lock when the transaxle is
shifted out of PARK (P). Automatic all door unlock
when the transaxle is shifted into PARK (P).
Mode 4: Automatic all door lock when the transaxle is
shifted out of PARK (P). Automatic driver's door only
unlock when the transaxle is shifted into PARK (P).
When your vehicle was shipped from the factory, it was
programmed to Mode 3. The mode to which your
vehicle was programmed may have been changed since
it left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:1. Close all doors and turn the ignition switch to ON.
2. Press and hold the power door lock switch in the
lock position.
3. While holding the door lock switch, cycle the
transaxle out of and back into PARK (P). The door
lock and unlock functions will operate as defined,
depending upon the current mode selected. (If you
do not wish to change the current mode, you can
either exit the programming mode by following the
instructions listed here or program the next feature
available on your vehicle).
4. After an initial transaxle cycle, each additional cycle
will advance to the operating mode by one, starting
from the current operating mode.
5. If cycled beyond Mode 4, the vehicle will enter
operating Mode 1. When the door lock switch is
released, the vehicle will remain in the most recent
operating mode.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
above or program the next feature available on
your vehicle.
Disconnecting the battery for up to a year will not
change or delete any previously programmed modes.

2-10 Rear Security Locks
Your vehicle is equipped
with rear door security
locks that help prevent
passengers from opening
the rear doors of your
vehicle from the inside.
To use one of these locks, do the following:
1. Open one of the rear doors.
2. On the inside of the rear door will be a lock. Insert
your master key into this lock and turn it upward.
This will engage the safety lock.
3. Close the door.
4. Do the same thing to the other rear door.The rear doors on your vehicle cannot be opened from
the inside when this feature is in use. If you want to
open the rear door when the security lock is on, unlock
the door from the inside and then open the door from
the outside.
Lockout Prevention
Lockout Prevention is a standard feature intended to
provide enhanced security and convenience. This feature
prevents a driver who has left the key in the ignition
from locking the doors using the power door lock
switch while any door is open.
This feature cannot guarantee that you will never be
locked out of your vehicle. If you don't leave the key
in the ignition, or if you use the manual door lock,
you could still lock your keys inside your vehicle.
Always remember to take your keys with you.
Programmable Modes
Mode 1: Turns feature on.
Mode 2: Turns feature off.

2-11
When your vehicle was shipped from the factory,
it was programmed to Mode 1. The mode to which
your vehicle was programmed may have been changed
since it left the factory. To determine the mode to which
your vehicle is programmed or to program your vehicle
to a different mode, do the following:
1. Open a door and put the key in the ignition.
2. Hold down the power door lock switch for more
than three seconds. This will turn the feature off
or on, depending upon the current mode selected.
(If you do not wish to change the current mode,
you can either exit the programming mode by
following the instructions listed here or program
the next feature available on your vehicle).
3. When the door lock switch is released, the vehicle
will remain in the most recent operating mode.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
above or program the next feature available on
your vehicle.Remote Keyless Entry System
(If Equipped)
If your vehicle has this feature, you can lock and unlock
your doors or unlock your trunk from about 3 feet (1 m)
up to 30 feet (9 m) away using the remote keyless entry
transmitter supplied with your vehicle.
Your keyless entry system operates on a radio frequency
subject to Federal Communications Commission (FCC)
Rules and with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with RSS
-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation of the device.

2-12
Changes or modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
At times you may notice a decrease in range. This is
normal for any remote system. If the transmitter does
not work or if you have to stand closer to your vehicle
for the transmitter to work, try this:

Check the distance. You may be too far from your
vehicle. You may need to stand closer during rainy
or snowy weather.

Check the location. Other vehicles or objects may
be blocking the signal. Take a few steps to the left
or right, hold the transmitter higher, and try again.

Check to determine if battery replacement is
necessary. See the instructions that follow.

If you're still having trouble, see your dealer or
a qualified technician for service.Operation
Press UNLOCK once to
unlock the driver's door
and to turn the interior
lamps on (see ªIllumination
on Remote Activationº in
the Index for more details).
Press UNLOCK again within five seconds to unlock all
doors. To lock all doors, press LOCK. To unlock the
trunk, press the trunk symbol on the remote keyless
entry transmitter. The trunk will only unlock when the
vehicle is in PARK (P).

2-13
Remote Alarm
When you press the alarm button on the remote keyless
entry transmitter, the headlamps will flash, the horn will
sound repeatedly and the interior lamps will illuminate.
This will allow you to attract attention if needed. The
alarm will continue until one of the following occurs:

The driver presses the alarm button on the remote
keyless entry transmitter a second time,

the ignition is turned to ON or

110 seconds has elapsed.
Remote Activation Verification (RAV)
This feature helps provide audible and/or visible
feedback that a remote keyless entry lock or unlock
command has been received and executed. The ignition
must be in OFF for the remote activation verification
to work.
You may select one of four operating modes for lock and
unlock commands. The selection and programming of the
lock and unlock modes are independent of each other.
Programmable Modes
Mode 1: No Verification
Mode 2: Horn Chirp onlyMode 3: Headlamp and Parking Lamp Flash only
Mode 4: Horn Chirp and Headlamp and Parking
Lamp Flash
RAV Lock Mode Programming
When your vehicle was shipped from the factory, it was
programmed to Mode 3. The mode to which your
vehicle was programmed may have been changed since
it left the factory. To determine the RAV lock mode to
which your vehicle is programmed to or to program
your vehicle to a different mode, do the following:
1. Close all doors and turn the ignition switch to ON.
2. Press and hold down the power door lock switch in
the LOCK position.
3. While holding the door lock switch, press and
release the remote keyless entry transmitter
LOCK button. This button press will initialize the
customization mode. Upon initiation of this mode,
the chime will sound. Count the number of chimes
you hear. The number of chimes tells you which
mode your vehicle is set for. (If you do not wish
to change the current mode, you can either exit the
programming mode by following the instructions
listed here or program the next feature available on
your vehicle).

2-14
4. Each additional press of the remote keyless entry
transmitter LOCK button will cause the vehicle to
advance to the RAV lock mode by one, starting
from the current RAV lock mode.
5. If cycled beyond RAV lock Mode 4, the vehicle will
enter RAV lock Mode 1. When the door lock switch
is released, the vehicle will remain in the most recent
RAV lock mode.
RAV Unlock Mode Programming
When your vehicle was shipped from the factory, it was
programmed to Mode 1. The mode to which your
vehicle was programmed may have been changed since
it left the factory. To determine the RAV unlock mode
to which your vehicle is programmed or to program
your vehicle to a different mode, do the following:
1. Close all doors and turn the ignition switch to ON.
2. Press and hold down the power door lock switch in
the UNLOCK position.
3. While holding the door lock switch, press and
release the remote keyless entry transmitter
UNLOCK button. This button press will initialize
the customization mode. Upon initiation of thismode, the chime will sound. Count the number of
chimes you hear. The number of chimes tells you
which mode your vehicle is set for. (If you do not
wish to change the current mode, you can either exit
the programming mode by following the instructions
listed here or program the next feature available on
your vehicle).
4. Each additional press of the remote keyless entry
transmitter UNLOCK button will cause the vehicle
to advance the RAV unlock mode by one, starting
from the current RAV unlock mode.
5. If cycled beyond RAV unlock Mode 4, the vehicle
will enter RAV unlock Mode 1. When the door lock
switch is released, the vehicle will remain in the
most recent RAV unlock mode.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
above or program the next feature available on
your vehicle.
Disconnecting the battery for up to a year will not
change or delete any previously programmed modes.

2-15
Illumination on Remote Activation
This feature is included on vehicles with the remote
keyless entry system. The interior illumination will be
activated when a remote keyless entry door unlock
command is received. The ignition must be off for the
remote activation illumination to work. The interior
lamps will illuminate until the ignition is turned to
ON or until the illumination period of 40 seconds
has elapsed.
If during the illumination period, a door is opened, the
timed illumination period will be cancelled, though the
interior lamps will remain on until all doors are closed.
Matching Transmitter(s) to Your Vehicle
Each remote keyless entry transmitter is coded to
prevent another transmitter from unlocking your vehicle.
If a transmitter is lost or stolen, a replacement can be
purchased through your dealer. Remember to bring
any remaining transmitters with you when you go to
your dealer. When the dealer matches the replacement
transmitter to your vehicle, any remaining transmitters
must also be matched. Once your dealer has coded the
new transmitter, the lost transmitter will not unlock your
vehicle. Each vehicle can have only four transmitters
matched to it.
Battery Replacement
Under normal use, the battery in your remote keyless
entry transmitter should last about three years.
You can tell the battery is weak if the transmitter won't
work at the normal range in any location. If you have
to get close to your vehicle before the transmitter works,
it's probably time to change the battery.
NOTICE:
When replacing the battery, use care not to
touch any of the circuitry. Static from your
body transferred to these surfaces may damage
the transmitter.