2001 Oldsmobile Intrigue Owner's Manuals

2-6
Door Locks
CAUTION:
Unlocked doors can be dangerous.

Passengers -- especially children -- can
easily open the doors and fall out of a
moving vehicle. When a door is locked,
the handle won't open it. You increase the
chance of being thrown out of the vehicle
in a crash if the doors aren't locked.
So, wear safety belts properly and lock
the doors whenever you drive.

Young children who get into unlocked
vehicles may be unable to get out. A child
can be overcome by extreme heat and can
suffer permanent injuries or even death
from heat stroke. Always lock your vehicle
whenever you leave it.

Outsiders can easily enter through an
unlocked door when you slow down or stop
your vehicle. Locking your doors can help
prevent this from happening.
There are several ways to lock and unlock your vehicle.
From the outside, use your key or keyless entry
transmitter (if equipped).
From the inside, use the manual lever. Each door has
a lever that works only on that door's lock. The lever
won't unlock or lock all the doors. Push the lever
rearward to unlock and forward to lock.

2-7 Power Door Locks
Press the power door lock
switch located on either
front door near the handle to
lock or unlock all the doors.
The rear doors do not have power door lock switches.
Push the manual lever rearward to unlock and forward
to lock.
Last Door Closed Locking
This feature allows the doors to be locked while the
passengers are leaving the vehicle. This also provides
a brief time period after all the doors are closed,
but before the doors lock, in which the doors may
be reopened.
Last door closed locking is activated by either the
power door lock switch inside the vehicle or by pressing
LOCK on the remote keyless entry transmitter
(if equipped). After pressing the power door lock
switch once, three chimes will be heard. The three
chimes indicate that the last door closed locking has
been activated.
If you wish to let the last door closed locking feature
complete the locking cycle, no additional action is
required. The last door closed locking feature will lock
the doors automatically after all the doors have been
closed for a period of five seconds. During this
five second period, any door may be reopened.
You can customize or disable the last door closed
locking feature. If disabled, the doors will lock
immediately when a power door lock switch is pressed.

2-8
Programmable Modes
Mode 1: Cancel the last door closed locking by
pressing the unlock switch or by fully inserting the
key in the ignition.
Mode 2: Override the last door closed locking feature
and lock the doors immediately by pressing the lock
switch a second time.
Mode 3: Let the last door closed locking feature
complete the locking of the vehicle.
When your vehicle was shipped from the factory,
it was programmed to Mode 3. The mode to which
your vehicle was programmed may have been changed
since it left the factory. To determine the mode to which
your vehicle is programmed or to program your vehicle
to a different mode, do the following:
1. Close all doors and turn the ignition switch to ON.
2. Press and hold the power door lock switch in the
unlock position.3. While holding the door unlock switch, cycle the
transaxle out of and back into PARK (P). Count the
number of chimes you hear. The number of chimes
tells you which mode your vehicle is set for. (If you
do not wish to change the current mode, you can
either exit the programming mode by following the
instructions listed here or program the next feature
available on your vehicle).
4. A single chime will be heard if the last door closed
locking feature is disabled, and two chimes will be
heard if the feature is enabled. After the initial
transaxle cycle, each additional cycle will turn
the last door closed locking feature on or off.
5. When the door unlock switch is released, the vehicle
will remain in the most recent operating mode.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
above or program the next feature available on
your vehicle.
Disconnecting the battery for up to a year will not
change any previously programmed modes.

2-9 Programmable Automatic Door Locks
Programmable automatic door locks is a standard
feature intended to provide enhanced security and
convenience by automatically locking and unlocking
vehicle doors. The automatic locking and unlocking of
the vehicle will occur if the ignition key is in ON and
the driver's door is closed when the vehicle is shifted
out of PARK (P).
Programmable Modes
Mode 1: No automatic door lock or unlock.
Mode 2: Automatic all door lock when the transaxle is
shifted out of PARK (P). No automatic door unlock.
Mode 3: Automatic all door lock when the transaxle is
shifted out of PARK (P). Automatic all door unlock
when the transaxle is shifted into PARK (P).
Mode 4: Automatic all door lock when the transaxle is
shifted out of PARK (P). Automatic driver's door only
unlock when the transaxle is shifted into PARK (P).
When your vehicle was shipped from the factory, it was
programmed to Mode 3. The mode to which your
vehicle was programmed may have been changed since
it left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:1. Close all doors and turn the ignition switch to ON.
2. Press and hold the power door lock switch in the
lock position.
3. While holding the door lock switch, cycle the
transaxle out of and back into PARK (P). The door
lock and unlock functions will operate as defined,
depending upon the current mode selected. (If you
do not wish to change the current mode, you can
either exit the programming mode by following the
instructions listed here or program the next feature
available on your vehicle).
4. After an initial transaxle cycle, each additional cycle
will advance to the operating mode by one, starting
from the current operating mode.
5. If cycled beyond Mode 4, the vehicle will enter
operating Mode 1. When the door lock switch is
released, the vehicle will remain in the most recent
operating mode.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
above or program the next feature available on
your vehicle.
Disconnecting the battery for up to a year will not
change or delete any previously programmed modes.

2-10 Rear Security Locks
Your vehicle is equipped
with rear door security
locks that help prevent
passengers from opening
the rear doors of your
vehicle from the inside.
To use one of these locks, do the following:
1. Open one of the rear doors.
2. On the inside of the rear door will be a lock. Insert
your master key into this lock and turn it upward.
This will engage the safety lock.
3. Close the door.
4. Do the same thing to the other rear door.The rear doors on your vehicle cannot be opened from
the inside when this feature is in use. If you want to
open the rear door when the security lock is on, unlock
the door from the inside and then open the door from
the outside.
Lockout Prevention
Lockout Prevention is a standard feature intended to
provide enhanced security and convenience. This feature
prevents a driver who has left the key in the ignition
from locking the doors using the power door lock
switch while any door is open.
This feature cannot guarantee that you will never be
locked out of your vehicle. If you don't leave the key
in the ignition, or if you use the manual door lock,
you could still lock your keys inside your vehicle.
Always remember to take your keys with you.
Programmable Modes
Mode 1: Turns feature on.
Mode 2: Turns feature off.

2-11
When your vehicle was shipped from the factory,
it was programmed to Mode 1. The mode to which
your vehicle was programmed may have been changed
since it left the factory. To determine the mode to which
your vehicle is programmed or to program your vehicle
to a different mode, do the following:
1. Open a door and put the key in the ignition.
2. Hold down the power door lock switch for more
than three seconds. This will turn the feature off
or on, depending upon the current mode selected.
(If you do not wish to change the current mode,
you can either exit the programming mode by
following the instructions listed here or program
the next feature available on your vehicle).
3. When the door lock switch is released, the vehicle
will remain in the most recent operating mode.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
above or program the next feature available on
your vehicle.Remote Keyless Entry System
(If Equipped)
If your vehicle has this feature, you can lock and unlock
your doors or unlock your trunk from about 3 feet (1 m)
up to 30 feet (9 m) away using the remote keyless entry
transmitter supplied with your vehicle.
Your keyless entry system operates on a radio frequency
subject to Federal Communications Commission (FCC)
Rules and with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with RSS
-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation of the device.

2-12
Changes or modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
At times you may notice a decrease in range. This is
normal for any remote system. If the transmitter does
not work or if you have to stand closer to your vehicle
for the transmitter to work, try this:

Check the distance. You may be too far from your
vehicle. You may need to stand closer during rainy
or snowy weather.

Check the location. Other vehicles or objects may
be blocking the signal. Take a few steps to the left
or right, hold the transmitter higher, and try again.

Check to determine if battery replacement is
necessary. See the instructions that follow.

If you're still having trouble, see your dealer or
a qualified technician for service.Operation
Press UNLOCK once to
unlock the driver's door
and to turn the interior
lamps on (see ªIllumination
on Remote Activationº in
the Index for more details).
Press UNLOCK again within five seconds to unlock all
doors. To lock all doors, press LOCK. To unlock the
trunk, press the trunk symbol on the remote keyless
entry transmitter. The trunk will only unlock when the
vehicle is in PARK (P).

2-13
Remote Alarm
When you press the alarm button on the remote keyless
entry transmitter, the headlamps will flash, the horn will
sound repeatedly and the interior lamps will illuminate.
This will allow you to attract attention if needed. The
alarm will continue until one of the following occurs:

The driver presses the alarm button on the remote
keyless entry transmitter a second time,

the ignition is turned to ON or

110 seconds has elapsed.
Remote Activation Verification (RAV)
This feature helps provide audible and/or visible
feedback that a remote keyless entry lock or unlock
command has been received and executed. The ignition
must be in OFF for the remote activation verification
to work.
You may select one of four operating modes for lock and
unlock commands. The selection and programming of the
lock and unlock modes are independent of each other.
Programmable Modes
Mode 1: No Verification
Mode 2: Horn Chirp onlyMode 3: Headlamp and Parking Lamp Flash only
Mode 4: Horn Chirp and Headlamp and Parking
Lamp Flash
RAV Lock Mode Programming
When your vehicle was shipped from the factory, it was
programmed to Mode 3. The mode to which your
vehicle was programmed may have been changed since
it left the factory. To determine the RAV lock mode to
which your vehicle is programmed to or to program
your vehicle to a different mode, do the following:
1. Close all doors and turn the ignition switch to ON.
2. Press and hold down the power door lock switch in
the LOCK position.
3. While holding the door lock switch, press and
release the remote keyless entry transmitter
LOCK button. This button press will initialize the
customization mode. Upon initiation of this mode,
the chime will sound. Count the number of chimes
you hear. The number of chimes tells you which
mode your vehicle is set for. (If you do not wish
to change the current mode, you can either exit the
programming mode by following the instructions
listed here or program the next feature available on
your vehicle).