Page 199 of 280
Do not start your engine with the air cleaner removed and do
not remove it while the engine is running.
OPENING THE HOOD
1. Inside the vehicle, pull the hood
release handle located under the
steering column on the instrument
panel.
2. Go to the front of the vehicle and release the auxiliary latch that is
located in the center between the hood and the grill.
3. Lift the hood until the lift cylinders hold it open.
Maintenance and care
199
Page 202 of 280
3. Set the parking brake and ensure the gearshift is securely latched in P
(Park).
4. Open the hood. Protect yourself from engine heat.
5. Locate and carefully remove the engine oil level indicator (dipstick).
²4.0L V6 engine
²5.0L V8 engine
MAX MIN
MAX MIN
Maintenance and care
202
Page 235 of 280
Replacing headlamp bulbs
To remove the headlamp bulb:
1. Make sure headlamp switch is in
OFF position, then lift hood and
open the hinged headlamp cover.
2. Disconnect the electrical
connector from the bulb by pulling
rearward.
3. Remove the bulb retaining ring by
rotating it counterclockwise (when
viewed from the rear) to free it
from the bulb socket, and slide the
ring off the plastic base. Keep the
ring to retain the new bulb.
4. Remove the old bulb from the
lamp assembly by gently pulling it
straight back out of the lamp
assembly.
To install the new bulb:
Handle a halogen headlamp bulb carefully and keep out of
children's reach. Grasp the bulb only by its plastic base and do
not touch the glass. The oil from your hand could cause the bulb to
break the next time the headlamps are operated.
LIFT
Maintenance and care
235
Page 236 of 280

If the bulb is accidentally touched, it should be cleaned with rubbing
alcohol before being used.
1. With the flat side of the new bulb's plastic base facing upward, insert
the glass end of the bulb into the lamp assembly. You may need to turn
the bulb left or right to align the grooves in the plastic base with the
tabs in the lamp assembly. When the grooves are aligned, push the bulb
into the lamp assembly until the plastic base contacts the rear of the
lamp assembly.
2. Install the bulb retaining ring over the plastic base until it contacts the
rear of the socket by rotating clockwise until you feel a ªstop.º
3. Install the electrical connector into the rear of the plastic base until it
snaps, locking it into position.
4. Turn the headlamps on and make sure they work properly. If the
headlamp was correctly aligned before you changed the bulb, you should
not need to align it again.
Replacing front parking lamp/turn signal bulbs
1. Make sure headlamp switch is in
OFF position, then lift hood and
open the hinged headlamp cover.
2. Remove screw from the lamp
assembly.
3. Disengage lamp assembly.
LIFT
Maintenance and care
236
Page 271 of 280

engine coolant temperature
gauge .........................................14
engine oil pressure gauge ........16
fuel gauge ..................................16
odometer ...................................15
speedometer .............................14
tachometer ................................15
trip odometer ............................15
GAWR (Gross Axle Weight
Rating) .......................................167
calculating ...............................169
definition .................................167
driving with a heavy load ......167
location ....................................167
GVWR (Gross Vehicle Weight
Rating) .......................................167
calculating .......................167, 169
definition .................................167
driving with a heavy load ......167
location ....................................167
H
Hazard flashers .........................177
Head restraints .........................113
Headlamps ...................................21
aiming ......................................240
autolamp system .......................94
bulb specifications ..................239
daytime running lights .............21
flash to pass ..............................22
high beam ...........................11, 21
replacing bulbs .......................235
turning on and off ....................21
warning chime ..........................13
Heating ........................................22
heating and air conditioning
system .......................................22HomeLink universal
transceiver (see Garage
door opener) .........................89±93
Hood ..........................................199
I
Ignition .........................77, 251±252
Infant seats
(see Safety seats) .....................136
Inspection/maintenance (I/M)
testing ........................................234
Instrument panel
cleaning ...................................244
cluster ..................................8, 244
lighting up panel and
interior .......................................22
location of components ..............8
J
Jack ............................................186
positioning ...............................186
storage .....................................186
Jump-starting your vehicle ......190
K
Keyless entry system ...............107
autolock ...................................108
keypad .....................................107
locking and unlocking doors ..108
programming entry code .......107
Keys ...................................110, 112
key in ignition chime ...............13
positions of the ignition ...........77
Index
271