Page 49 of 56
COMFORT ADJUSTMENT
121
16G052
Move seat fully back
CAUTION
A forward±facing child restraint system should be
allowed to be put on the front passenger seat only when
it is unavoidable. Always move the seat as far back as
possible, because the force of the deploying front
passenger airbag could cause death or serious injury to
the child. Do not allow the child to lean over the front
door or around the front door even if the child is seated
in a child restraint system. It is dangerous if the side and
curtain shield airbags inflate, and the impact could
cause death or serious injury to the child.
16G053
1. Sit the child on a booster seat. Run the lap and shoulder belt
through or around the booster seat and child following the
instructions provided by its manufacturer and insert the tab into
the buckle.
Make sure the shoulder belt is correctly across the child's
shoulder and that the lap belt is positioned as low as possible
on child's hips. See ºSeat beltsº on page 86 for details.
CAUTION
Always make sure the shoulder belt is positioned
across the center of child's shoulder. The belt should
be kept away from child's neck, but not falling off
child's shoulder. Failure to do so could reduce the
amount of protection in an accident and cause
serious injuries in a collision.
Page 50 of 56
COMFORT ADJUSTMENT
122
Both high±positioned lap belts and loose±fitting
belts could cause serious injuries due to sliding
under the lap belt during a collision or other
unintended result. Keep the lap belt positioned as
low on a child's hips as possible.
For child's safety, do not place the shoulder belt
under child's arm.
After inserting the tab, make sure the tab and buckle
are locked and that the lap and shoulder portions of
the belt are not twisted.
Do not insert coins, clips, etc. in the buckle as this
may prevent your child from properly latching the tab
and buckle.
If the seat belt does not function normally,
immediately contact your Lexus dealer. Do not use
the seat until the seat belt is fixed. It cannot protect
your child from injury.
16G054
2. To remove the child restraint system, press the
buckle±release button and allow the belt to retract.
Page 51 of 56
COMFORT ADJUSTMENT
123
Using a top strap
16G060a
Follow the procedure below for a child restraint system
that requires the use of a top strap.
16G099b
Anchor brackets
Use the anchor bracket on the filler panel behind the rear seat
to attach the top strap.
Anchor brackets are installed for each rear seating position.
Page 52 of 56
COMFORT ADJUSTMENT
124
16G078a
1. Fix the child restraint system with the seat belt.
2. Latch the hook onto the anchor bracket and tighten the
top strap.
For instructions to install the child restraint system, see ªType
of child restraint systemº on page 111.
CAUTION
Make sure the top strap is securely latched, and
check that the child restraint system is secure by
pushing and pulling it in different directions.
Follow all the installation instructions provided by its
manufacturer.
INSTALLATION WITH CHILD RESTRAINT LOWER
ANCHORAGES
16g247
The lower anchorages for the child restraint system
interfaced with the FMVSS225 specification are installed
in the rear seat.
The anchorages are installed in the clearance between the
seat cushion and seatback of both outside rear seats.
Child restraint system interfaced with the FMVSS225
specification can be fixed with these anchorages. In this case,
it is not necessary to fix the child restraint system with a seat
belt on the vehicle.
Page 53 of 56
COMFORT ADJUSTMENT
125
16g230d
Type A
16g231b
Type B
Page 54 of 56
COMFORT ADJUSTMENT
126CHILD RESTRAINT SYSTEM INSTALLATION
Type A:
1. Widen the clearance between the seat cushion and
seatback a little and confirm the position of the lower
anchorages below the tag in the seatback.
2. Latch the hooks of lower straps onto the anchorages
and tighten the lower straps.
Type B:
1. Widen the clearance between the seat cushion and
seatback a little and confirm the position of the lower
anchorages below the tag in the seatback.
2. Latch the buckles onto the anchorages
If your child restraint system has a top strap, it should be
anchored. (For the installation of the top strap, see ªÐUsing a
top strapº on page 123 in this section.)
For the installation details, refer to the instruction manual
equipped with each product.
CAUTION
When using the lower anchorages for the child
restraint system, be sure that there are no irregular
objects around the anchorages or that the seat belt is
not caught.
Push and pull the child restraint system in different
directions to be sure it is secure. Follow all the
installation instructions provided by its
manufacturer.
Do not put a child restraint system on the rear seat if
it interferes with the lock mechanism of the front
seats. This can cause severe injury to the child and
front passenger in case of sudden braking or a
collision.
Page 55 of 56
COMFORT ADJUSTMENT
127
DRIVING POSITION MEMORY
SYSTEM
The micro computer can memorize the position of the driver's
seat, and the positions of the tilt and telescopic steering, and
outside rear view mirrors. Two different driving position
profiles can be entered into the computer's memory.
Recording a driving position in the computer's memory can
only be done when the ignition key is in the ºONº position and
the selector lever is in the ºPº position.
Setting a driving position
16G064a
1. Adjust the driver's seat, tilt and telescopic steering and
outside rear view mirrors to the desired position.
2. While pushing the ºSETº button, push button º1º or º2º
until the signal beeps.The beep sound means that the positions are recorded in the
computer's memory.
By repeating these two steps and pressing the remaining
button, the driving position for another driver can be recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized position,
the easiest way is to first activate the memorized position, then
make the desired changes and perform step 2 above.
Activating a memorized position
16G065a
When you push button º1º or º2º, the driving position will
be automatically adjusted to the position recorded for that
button.
Page 56 of 56
COMFORT ADJUSTMENT
128Conditions for memorized position activation
Ignition key ºONº and selector lever in ºPº position.
All parts of the memorized positions can be activated.
However, if the brake pedal is being depressed, the seat
position will not change.
Key not in ignition switch and within 30 seconds of opening
driver's door.
The memorized position can be activated, except for the tilt
and telescopic steering.
If any driving position memory switch is pushed while one of
the memorized driving position profiles is being activated, the
operation will stop.
To activate the system, push the desired button (º1º or º2º)
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
If the vehicle's battery is disconnected, the computer's
memory will be erased and the memorized positions will have
to be set again.
CAUTION
Do not start the vehicle while the adjustments are
being made.
Take care not to select the wrong button, or the seat
could strike the rear passenger or hit your body
against the steering wheel. If this happens, you can
stop the movement by pressing another driving
position memory switch, or depressing the brake
pedal.
