Page 148 of 504
COMFORT ADJUSTMENT
131
CAUTION
Do not adjust the mirror while the vehicle is moving.
It may cause the driver to mishandle the vehicle and
an accident may occur resulting in death or serious
injuries.
Since the mirror surfaces can get hot, keep your
hands off them when the rear window and outside
rear view mirror defogger switch is on.
Page 149 of 504
COMFORT ADJUSTMENT
132
Power rear view mirror control
16E011
1Control switch 2Master switch
To adjust the power rear view mirror, first place the
master switch at ªLº (left) or ªRº (right), and push
the control switch on the desired side.
The power rear view mirror can be adjusted when the
key is in the ªACCº or ªONº position.
NOTICE
If ice should jam the mirror, do not operate thecontrol or scrape the mirror face. Use a sprayde±icer to free the mirror.
Page 150 of 504
COMFORT ADJUSTMENT
133
Folding rear view mirrors
16E198
To fold the rear view mirror, push backward.
The rear view mirrors can be folded backward for
parking in restricted areas.
CAUTION
Do not drive with the mirrors folded backward. Both the
driver and passenger side rear view mirrors must be
extended and properly adjusted before driving.
Page 151 of 504
COMFORT ADJUSTMENT
134
INSIDE REAR VIEW MIRROR
16E178
Page 152 of 504
COMFORT ADJUSTMENT
135
Adjust the m
irror so that you can just see the rear of
your vehicle in the mirror.
Pushing the switch changes the mode between
ªAUTOº and ªDAYº.
The indicator comes on when the ªAUTOº mode is
selected.
ªDAYº mode: The mirror surface is normal.
ªAUTOº mode: If the mirror detects light from the
headlights of the vehicle behind you, the mirror
surface darkens slightly to reduce the reflected
light.
When the inside rear view mirror surface changes, the
driver's side outside rear view mirror surface will also
become darker.
When the ignition key is inserted and turned on, the
inside rear view mirror always turns on in the ªAUTOº
mode. When the outside air temperature is low, it may take a
little longer for the mirror to darken in response to the
detection of headlights.
CAUTION
Do not adjust the mirror while the vehicle is moving. It
may cause the driver to mishandle the vehicle and an
accident may occur resulting in death or serious
injuries.
Page 221 of 504
COMFORT ADJUSTMENT
204
DRIVING POSITION MEMORYSYSTEM
The micro computer can memorize the positions of the
driver's seat and outside rear view mirrors. Two dif ferent
driving position profiles can be entered into the
computer's memory.
Recording a driving position in the computer's memory
can only be done when the ignition key is in the ªONº
position and the selector lever is in the ªPº position.
Setting a driving position
16E047
Page 222 of 504
COMFORT ADJUSTMENT
205
1. Adjust the driver's seat and outside rear view
mirrors to the desired position.
2. While
pushing the ªSETº button, push button ª1º
or ª2º until the signal beeps.
The beep sound means that the positions are recorded
in the computer's memory. By repeating these two steps and pressing the
remaining button, the driving position for another driver
can be recorded.
To set a new memorized position, select the desired
position and perform step 2. The previous memory will
be erased and the new position will be set.
To make only slight changes to an already memorized
position, the easiest way is to first activate the
memorized position, then make the desired changes
and perform step 2 above.
Page 295 of 504
STARTING AND DRIVING
278
To allow proper operation of your vehicle's
ventilation system, keep the inlet grilles in front
of the windshield clear of snow, leaves, or other
obstructions.
If you smell exhaust fumes in the vehicle, drive
with the windows open and the trunk lid closed.
Have the cause immediately located and
corrected.BEFORE STARTING THE ENGINE
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, head restraint
height and steering wheel angle.
3. Adjust the inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.
Remember to check that the service reminder indicators
function when turning the key to ªONº, and check the fuel
gauge to see that you have sufficient fuel.