2001 LAND ROVER FREELANDER check engine

FUEL DELIVERY SYSTEM - PETROL
ADJUSTMENTS 19-2-5
Fuel system - pressure test - KV6 - NAS
$% 19.50.13
Remove
1.Remove acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2.Position absorbent cloth beneath fuel rail.
WARNING: Fuel vapour is highly flammable
and in confined spaces is also explosive
and toxic. Always have a fire extinguisher
containing foam, CO
2, gas or powder close
at hand when handling or draining fuel.
3. Up to 03MY: Remove nut and bolt securing coil
and position coil aside.
4.Connect adaptor LRT-19-006, to pressure
gauge LRT-19-004 .
5.Remove schraeder valve cap.
6.Connect pressure gauge to fuel rail schraeder
valve.
7.Start engine. Pressure at idle = 3.4 bar. If
pressure is below 3.4 bar, suspect the following
in order: fuel hoses, filter, regulator and pump.
Refit
1.Stop engine.
2.Disconnect pressure gauge LRT-19-006 and
adapter LRT-19-004 from fuel rail.
3. Up to 03MY: Fit and tighten nut and bolt
securing coil.
4.Fit acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
Fuel system - pressure test - K1.8
$% 19.50.13
Check
1.Disconnect battery earth lead.
2.Position absorbent cloth beneath fuel pipe to
catch spillage.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
3.Disconnect fuel pipe from inlet manifold.
4.Connect LRT-19-004A to manifold and fuel
pipe.
Note:: LRT-19-004X can be used as an
alternative.
5.Connect battery earth lead.
6.Start engine. Pressure at idle = 3.6 bar ± 0.2
bar.
7.Stop engine. If pressure is out of tolerance
suspect the following in order: fuel hoses, filter
and pump.
8.Remove plug, reconnect vacuum hose and
secure hose with clip.
9.Disconnect battery earth lead.
10.Disconnect LRT-19-004A from fuel pipe and
inlet manifold.
11.Connect fuel pipe to manifold.
12.Connect battery earth lead.
LRT - 19 -004A
M19 3675

FUEL DELIVERY SYSTEM - PETROL
19-2-10 REPAIRS
Cable - throttle - KV6
$% 19.20.06
Remove
1.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
Pre 03MY illustrated.
2.Release throttle cable from clips on harness
brackets.
3.Release throttle cable from abutment bracket
and disconnect cable from throttle body cam.4.Release clip securing throttle inner cable to
throttle pedal and disconnect inner cable from
pedal.
5.Rotate throttle outer cable to release from
bulkhead and remove cable from vehicle.
Refit
1.Position cable, secure to bulkhead and connect
inner cable to throttle pedal.
2.Connect throttle inner cable to throttle cam and
secure outer cable in abutment bracket.
3.Secure throttle cable in clips on harness
brackets.
4.Adjust throttle cable.

+ FUEL DELIVERY SYSTEM -
PETROL, ADJUSTMENTS, Throttle cable -
check and adjust - KV6.
5.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-21
Refit
1.Clean mating faces of IACV and throttle body.
2.Fit new gasket, position IACV to throttle body,
fit and tighten Allen screws to 6 Nm (4.5 lbf.ft).
3.Clean TP sensor and throttle body mating face.
4.Fit TP sensor to throttle spindle. Ensure that
during fitting the machined flat on the throttle
spindle is aligned with the mating portion of the
TP sensor
CAUTION: The throttle position sensor can
be easily damaged during fitting. When
pressing the sensor onto the throttle
spindle, use fingers only, and only apply
pressure to the area shown shaded in the
illustration.
5.Rotate TP sensor in an anti-clockwise direction
to align fixing holes.
CAUTION: Do not rotate throttle position
sensor in a clockwise direction and ensure
that it is not rotated beyond its internal
stops.
6.Fit TP sensor specification plate.
7.Fit new Torx screws and wave washers, tighten
Torx screws to 1.5 Nm _1.0 lbf.ft).
8. Vehicles with cruise control: Position
actuator support bracket to throttle body. Fit
Torx screws and tighten to 9 Nm (7 lbf.ft).
Connect actuator arm to throttle linkage.
9.Clean throttle body and mating face on inlet
manifold chamber.
10.Fit new seal to inlet manifold chamber.
11.Position throttle body to inlet manifold chamber,
fit and tighten Torx screws to 7 Nm ( 5 lbf.ft).
12.Connect multiplugs to TP sensor and IACV.
13. Vehicles with cruise control: Connect cruise
control actuator vacuum hose.
14.Connect primary throttle cable to throttle cam
and abutment bracket.
15.Connect engine breather/vacuum pipes to
throttle body and IACV.16.Adjust throttle cable.

+ FUEL DELIVERY SYSTEM -
PETROL, ADJUSTMENTS, Throttle cable -
check and adjust - KV6.
17.Connect battery earth lead.
18.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
19.Retune using TestBook
M18 0695

FUEL DELIVERY SYSTEM - PETROL
19-2-40 REPAIRS
Refit
1.Remove protective caps from each injector.
2.Clean injectors and recesses in fuel rail and
inlet manifold.
3.Lubricate new 'O' ring with castor oil and fit to
injector.
4.Fit injectors to fuel rail and secure with spring
clips.
5.Position fuel rail assembly and connect injector
multiplugs.
6.Fit injector spacer.
7.Push each injector into inlet manifold.
8.Fit bolts securing fuel rail to inlet manifold and
tighten to 8 Nm ( 6 lbf.ft).
9.Connect fuel feed hose to fuel rail.
10.Fit engine oil dipstick.
11.Connect vacuum pipe to fuel pressure regulator
and secure with clip.
12.Connect battery earth lead.
Actuator unit - cruise control - KV6 - non
NAS
$% 19.75.05
Remove
1.Disconnect battery earth lead.
2.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
3.Disconnect vacuum hose from actuator.
4.Remove nut securing actuator to mounting
bracket.
5.Release operating rod from throttle cam and
remove actuator.
Refit
1.Position actuator and connect operating rod to
throttle cam.
2.Position actuator into mounting bracket, fit and
tighten nut.
3.Connect vacuum hose to actuator.
4.Check pull rod to retainer clearance, with lever
fully returned, pull rod should just be held by
retainer.
5.Release retainer by turning anti-clockwise,
eliminate clearance then rotate retainer half
turn clockwise. Check pull rod is just held and
rotate retainer a further quarter turn clockwise
to lock.
6.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
7.Connect battery earth lead.

COOLING SYSTEM - K SERIES KV6
ADJUSTMENTS 26-3-1
COOLING SYS TEM - K SER IES KV6 ADJUST ME NTS
Coolant - drain and refill
$% 26.10.01
Drain
1.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2.Visually check engine and cooling system for
signs of coolant leaks.
WARNING: Since injury such as scalding
could be caused by escaping steam or
coolant, do not remove the filler cap from
the coolant expansion tank while the
system is hot.
3.Examine hoses for signs of cracking, distortion
and security of connections.
4.Remove expansion tank filler cap.
5.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
6.Position container to collect coolant.
7.Remove cylinder block drain plug.
8.Release clip and remove bottom hose from
radiator.
9.Allow cooling system to drain.Refill
1.Flush system with water under low pressure.
Do not use water under high pressure as it
could damage the radiator.
2.Clean cylinder block drain plug and apply
sealant, Part No. STC 50552 to first 3 threads.
3.Fit cylinder block drain plug and tighten to 20
Nm (15 lbf.ft).
4.Fit bottom hose to radiator and secure with clip.
5.Prepare coolant to required concentration.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS, Fluids.
6.Remove bleed screw from heater return hose.
7.Slowly fill the system through the coolant
expansion tank until a steady flow of coolant is
emitted from the bleed hole.
8.Fit and close bleed screw in heater return hose.
9.Continue to fill system through the expansion
tank until coolant reaches to the base of the
expansion tank bleed hose.
10.Fit expansion tank filler cap.
11.Start and run engine at idle speed for 5
minutes.
CAUTION: DO NOT operate air conditioning
12.Switch off engine.
13.Squeeze bottom hose several times to remove
any trapped air.
14.Start engine and run at speeds varying
between idle speed and 3500 rev/min for 7
minutes.
15.Switch off engine and allow to cool.
16.Remove expansion tank filler cap and add
coolant until it reaches the 'MAX' mark on the
expansion tank.
17.Fit expansion tank filler cap.
18.Start and run engine until normal operating
temperature is reached.
CAUTION: The bottom hose must be warm/
hot, this will ensure the thermostat is fully
open.

COOLING SYSTEM - K SERIES KV6
26-3-2 ADJUSTMENTS
19.Ensure warm air is available at vents.
NOTE: If warm air is not available, an air-lock
may be present in heater matrix. If necessary,
allow engine to cool, remove expansion tank
filler cap and repeat bleed operation at heater
hose
20.Switch off engine and allow to cool.
21.Check for leaks and top-up coolant to 'MAX'
mark on expansion tank
22.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
23.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
REPAIRS 30-3-17
30.Remove and discard seals from inlet manifold
chamber and 'O' rings from RH inlet manifold.Refit
1.Clean seal faces on inlet manifold chamber and
inlet manifolds.
2.Fit new 'O' rings to RH inlet manifold and new
seals to manifold chamber.
3.Position inlet manifold chamber, secure RH coil
harness clips in inlet manifold chamber support
brackets.
4.Connect multiplugs to plug top coils and secure
with locking clips.
5.Align inlet manifold chamber to inlet manifolds,
fit and tighten bolts to 18 Nm (13 lbf.ft).
6.Align inlet manifold chamber support brackets
to RH camshaft cover, fit and tighten bolts to 10
Nm (7.5 lbf.ft).
7.Position engine harness brackets to inlet
manifold chamber, fit and tighten screws.
8.Connect multiplugs to VIS motors.
9. NAS models: Connect engine breather pipe.
10. NAS models: Connect multiplugs to IAT and
MAF sensors.
11.Connect brake servo vacuum hose to inlet
manifold chamber.
12.Connect vacuum/breather hoses to LH and RH
camshaft covers and to throttle body.
13.Connect cruise control actuator vacuum pipe.
14. Non NAS models: Connect vacuum hose to
IACV housing.
15. Non NAS models: Connect multiplugs to TP
and IACV sensors.
16.Connect vacuum/breather hoses to LH
camshaft cover, 'T' piece and purge control
valve.
17. Non NAS models: Connect small vacuum
hose to purge control valve.
18.Connect multiplug to purge control valve .
19.Connect EVAP hose to purge control valve.
20.Connect fuel hose to fuel rail pipe, fit rubber
sleeve over hose connector.
21.Remove absorbent cloth.
22. Non NAS models: Connect throttle inner cable
to throttle cam and secure outer cable in
abutment bracket.
23. Non NAS models: Secure throttle cable in
clips on harness brackets.
24.Adjust throttle cable, if fitted.

+ FUEL DELIVERY SYSTEM -
PETROL, ADJUSTMENTS, Throttle cable -
check and adjust - KV6.
25.Remove vacuum enhancer.

+ BRAKES, REPAIRS, Vacuum -
enhancer - KV6.
26.Connect battery earth lead.

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
30-3-22 REPAIRS
Refit
1.Clean seal faces on inlet manifold chamber and
inlet manifolds.
2.Fit new 'O' rings to RH inlet manifold and new
seals to inlet manifold chamber.
3.Position inlet manifold chamber, secure RH coil
harness clips in inlet manifold chamber support
brackets.
4.Align inlet manifold chamber to inlet manifolds,
fit and tighten bolts to 18 Nm (13 lbf.ft).
5.Align inlet manifold chamber support brackets
to RH camshaft cover, fit and tighten bolts to 10
Nm (7 lbf.ft).
6.Connect multiplugs to plug top coils and secure
with locking clips.
7.Position engine harness brackets to inlet
manifold chamber, fit and tighten screws.
8.Connect multiplugs to VIS motors.
9. NAS models: Align harness and fuel feed pipe.
Secure harness and pipe in clip on manifold
chamber.
10. NAS models: Using a new clip, fit intake hose
to throttle body and secure hose with clip.
11. NAS models: Connect multiplug to throttle
body.
12. NAS models: Connect multiplugs to IAT and
MAF sensors.
13. NAS models: Fit vacuum/breather pipe and
connect to LH camshaft cover, RH camshaft
cover link pipe and inlet manifold chamber.
14. NAS models: Using a new clip, fit vacuum/
breather pipe to engine air intake hose and
secure pipe with clip.
15. NAS models: Connect vacuum/breather pipe
to LH and RH camshaft covers. Fit pipe into
clip.16. Non NAS models: Connect cruise control
actuator vacuum pipe.
17. Non NAS models: Fit vacuum/breather pipe to
throttle body and connect pipe to LH and RH
camshaft covers.
18. Non NAS models: Fit vacuum/breather pipe to
purge control valve and LH camshaft cover.
Using a new clip, connect pipe to 'T' piece and
secure pipe with clip.
19. Non NAS models: Connect multiplug to TP
sensor.
20. Non NAS models: Connect multiplug to IACV.
21. Non NAS models: Connect vacuum pipe to
IACV.
22. Non NAS models: Connect small vacuum pipe
to purge control valve.
23.Connect multiplug to purge control valve .
24.Connect EVAP hose to purge control valve.
25.Connect fuel hose to fuel rail pipe, fit rubber
sleeve over hose connector.
26. Non NAS models: Connect throttle inner cable
to throttle cam and secure outer cable in
abutment bracket.
27. Non NAS models: Secure throttle cable in
clips on harness brackets.
28. Non NAS models: Adjust throttle cable.

+ FUEL DELIVERY SYSTEM -
PETROL, ADJUSTMENTS, Throttle cable -
check and adjust - KV6.
29.Fit vacuum enhancer.

+ BRAKES, REPAIRS, Vacuum -
enhancer - KV6.
30.Connect the battery earth lead.