2001 LAND ROVER FREELANDER wheel bolts

DRIVESHAFTS
REPAIRS 47-7
10.With assistance pull hub assembly outwards
and release drive shaft outer joint from hub
assembly.
11.Taking care not to damage 'Flinger', release
drive shaft inner joint from differential using
LRT-51-014 and remove drive shaft.
12.Remove and discard drive shaft circlip.Refit
1.Inspect differential seal, renew if worn or
damaged.
2.Clean ends of drive shaft and locations in hub
and differential.
3.Lubricate oil seal running surface with
transmission oil.
4.Fit new circlip to drive shaft.
5.Fit drive shaft to differential and push fully
home.
CAUTION: Pull the drive shaft to ensure the
circlip is fully engaged and retains the shaft.
6.With assistance fit drive shaft to hub.
7.Fit new drive shaft nut but do not tighten at this
stage.
8.Fit nut, bolt and dynamic damper to adjustable
transverse link and tighten to 120 Nm (89 lbf.ft).
CAUTION: Nuts and bolts must be tightened
with the weight of the vehicle on the
suspension.
9.Fit nut and bolt to fixed transverse link and
tighten to 120 Nm (89 lbf.ft).
10.Fit spacer, nut and bolt to trailing link and
tighten to 120 Nm (89 lbf.ft).
11.Fit new drive shaft nut and tighten to 400 Nm
(295 lbf.ft). Stake nut to shaft.
12.Check and top up oil level.

+ MAINTENANCE, MAINTENANCE,
Rear Axle.
13.Fit road wheel(s) and tighten nuts to 115 Nm 85
lbf.ft).
14.Remove stands and lower vehicle.
15.Connect battery earth lead.

DRIVESHAFTS
REPAIRS 47-9
Gaiter - inner joint - rear
$% 47.11.16
Remove
1.Disconnect battery earth lead.
2.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove outer gaiter.

+ DRIVESHAFTS, REPAIRS, Gaiter -
outer - rear.
5.Release both gaiter clips and discard.
6.Slide gaiter from shaft.
Refit
1.Clean drive shaft and gaiter.
2.Apply grease from the sachet to the joint.
3.Fit new gaiter to shaft.
4.Apply grease from the sachet to the joint.
5.Position gaiter to joint and use a 'Band-it
thriftool' LRT-99-019 to secure the 2 new clips.
6.Fit outer gaiter.

+ DRIVESHAFTS, REPAIRS, Gaiter -
outer - rear.
7.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
8.Remove stands and lower vehicle.
9.Connect battery earth lead.
Propeller shaft assembly
$% 47.15.01
Remove
1.Raise vehicle on a 4 post ramp.
2.Raise one wheel on each axle for rotation of
propeller shaft as necessary to access fixings.
CAUTION: When working on the propeller
shafts:
lAlways remove the propeller shafts and
viscous coupling as an assembly.
Dismantling the individual units on the
vehicle may cause damage to the
components.
lNever unbolt the viscous coupling
support bearings from the body without
first detaching the propeller shafts at the
differential and IRD. The weight of the
centre section will pull the CV joint apart,
causing irreparable damage.
lNever allow the CV joint to be
manipulated to an acute angle. This will
cause the internal roller bearings to
break up, leading to excessive backlash
and CV joint failure.
3.Reference mark the position of propeller shaft
flanges to IRD and rear axle flanges to aid
reassembly.
4.Remove 6 nuts, bolts and link washers
securing CV joint to IRD flange.

DRIVESHAFTS
47-10 REPAIRS
5.Release the CV joint from IRD flange by pulling
on the main casing of the CV joint . If
necessary, position a clamp around the CV
joint main body, release the CV joint by levering
between the clamp and the IRD flange. Support
the front of propeller shaft.
6.Remove 4 nuts and bolts securing propeller
shaft to rear axle flange, release and support
propeller shaft from rear axle flange.
7.Remove 4 bolts securing viscous coupling
support bearings.
CAUTION: Support the weight of viscous
coupling and propeller shaft.
8.With assistance remove complete propeller
shaft assembly.Refit
1.Clean propeller shaft flanges and mating faces.
2.With assistance, fit propeller shaft assembly in
position, support front and rear propeller shafts
at each end.
3.Align viscous coupling support bearings, fit
bolts but do not tighten at this stage.
4.Position propeller shaft to rear axle and align
reference marks.
5.Fit and tighten nuts and bolt securing propeller
shaft to rear axle to 65 Nm (48 lbf.ft).
6.Position propeller shaft to IRD flange, align
flange reference marks.
7.Fit nuts and bolts securing front propeller shaft
to IRD flange and tighten to 40 Nm (30 lbf.ft).
8.Correctly position support bearings at 90° to the
centre line as shown at points 'A' and 'B' ,
tighten rear then front bolts to 28 Nm (21 lbf.ft).
9.Lower wheels.
10.Lower vehicle.

REAR AXLE & FINAL DRIVE
51-6 REPAIRS
Refit
1.Fit new collapsible spacer.
2.Fit pinion bearing and oil thrower.
3.Clean pinion flange and oil seal recess.
4.Fit new oil seal using LRT-51-010.
5.Fit pinion flange and washer.
6.Restrain pinion flange using LRT- 51-003.
7.Fit new pinion nut and tighten to 190 Nm (140
lbf.ft).
8.Check for end float on pinion. If end float exists
continue to tighten pinion nut until end float is
removed.
9.Continue to tighten pinion nut until correct
preload is obtained.
10.Pinion preload is 1.7 - 2.8 Nm (1.2 - 2.1 lbf.ft), if
higher replace collapsible spacer.
CAUTION: Do not tighten pinion nut to more
than 373 Nm (275 lbf.ft), or the collapsible
spacer will compress too far.
11.Clean propeller shaft flange and mating face.
12.Position propeller shaft to rear axle and align
reference marks.
13.Tighten propeller shaft nuts and bolts to 65 Nm
(48 lbf.ft).
14.Fit drive shafts.

+ REAR AXLE & FINAL DRIVE,
REPAIRS, Oil seal - differential housing.
15.Check differential oil level.

+ MAINTENANCE, MAINTENANCE,
Rear Axle.
Oil seal - differential housing
$% 51.20.36
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel.
3.Remove bolt securing handbrake cable to
subframe.
4.Remove nut and bolt securing trailing link to
rear hub, collect spacer from under bolt head.
5.Remove nut and bolt securing fixed transverse
link to subframe. Collect dynamic damper.
6.Remove nut and bolt securing adjustable
transverse link to subframe.
7.Position drain tin to catch oil spillage.
8.With assistance pull hub assembly outwards.

REAR AXLE & FINAL DRIVE
REPAIRS 51-7
9.Taking care not damage oil seal 'flinger',
release drive shaft from differential using LRT-
51-014 and position shaft aside.
10.Remove and discard circlip from drive shaft.
11.Remove differential oil seal.Refit
1.Clean drive shaft oil seal recess in axle casing.
2.Fit new oil seal using LRT-51-012.
3.Clean end of drive shaft and location in
differential.
4.Check condition of oil seal 'Flinger', renew if
damaged.
5.Fit new circlip to drive shaft.
6.With assistance fit drive shaft to differential,
push drive shaft fully home to engage circlip.
7.Fit nut and bolt to fixed transverse link and
tighten to 120 Nm (89 lbf.ft).
CAUTION: Nuts and bolts must be tightened
with weight of vehicle on suspension.
8.Fit nut, bolt and dynamic damper to adjustable
transverse link and tighten to 120 Nm (89 lbf.ft).
9.Fit spacer, nut and bolt to trailing link and
tighten to 120 Nm (89 lbf.ft).
10.Fit bolt securing handbrake cable clip and
tighten to 22 Nm (16 lbf.ft).
11.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
12.Check differential oil level.

+ MAINTENANCE, MAINTENANCE,
Rear Axle.
13.Remove stands and lower vehicle.

STEERING
57-2 ADJUSTMENTS
Front wheel alignment - check & adjust
$% 57.65.01
Check
1.Ensure tyre pressures are correct and vehicle
is at kerbside weight.
2.Roll vehicle backwards and forwards to relieve
stresses in steering and suspension.
3.Ensure that wheel alignment equipment is
properly calibrated.
4.Check front wheel alignment is within
tolerance.

+ GENERAL DATA, Steering.
Adjust
1.Mark position of steering ball joints for
reference.
2.Loosen track rod and ball joint pinch bolts.3.Rotate turn buckle to obtain correct alignment.
Ensure ball joint is not rotated.
CAUTION: Both track rods must be rotated
an equal amount.
4.Recheck front wheel alignment.
5.Tighten track rod and ball joint pinch bolts to 28
Nm (21 lbf.ft).
CAUTION: Ensure slots in turn buckle
clamps are aligned.

STEERING
REPAIRS 57-5
REPAIRS
Power steering rack
$% 57.10.01
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove front road wheels.
3.Remove and discard nuts securing track rod
ball joints to steering arms.
4.Fit an M12 nut to each ball pin, flush with end of
each pin.
5.Using LRT-57-043, separate ball pins from RH
and LH steering arms. Remove M12 nuts and
release ball pins from steering arms.
6.Remove pinch bolt securing steering column to
PAS rack pinion.7. KV6 models: Remove 2 nuts securing steering
rack heat shield and remove heat shield.
8. KV6 models: Remove 2 bolts securing coolant
rail to cylinder block.
9. Td4 manual models: Using tool LRT-37-050
release gear change rods from gear change
linkage.
10. Td4 manual models: Remove 2 bolts securing
gearchange linkage to bulkhead and tie aside.

STEERING
REPAIRS 57-7
25.Remove dust seal from pinion housing.
Refit
1.Fit PAS rack to vehicle from passengers side.
2.Fit dust shield to pinion housing.
3. KV6 models: Fit RH Hydramount.

+ ENGINE - K SERIES KV6, REPAIRS,
Hydramount - engine - RH.
4.Ensure pipe unions are clean.
5.Fit new 'O' rings to fluid pipes.
6.Fit fluid pipes to PAS rack but do not tighten at
this stage.
7.Align fluid pipe bracket to PAS rack, fit bolt but
do not tighten at this stage.
8.With assistance fit PAS rack pinion to steering
column, ensuring column coupling is aligned
with gear input flag.
9.Fit washers and new bolts securing steering
rack mounting to bulkhead, but do not tighten at
this stage. Ensure large washer is fitted to lower
bolt.
10.Fit rubber mount and clamp to PAS rack.
11.Fit bolts securing clamp to bulkhead but do not
tighten at this stage.
12.Tighten PAS rack mounting bolts to 45 Nm (33
lbf.ft).
13.Tighten PAS rack clamp bolts to 45 Nm (33
lbf.ft).
14.Tighten PAS rack fluid feed pipe union to 18
Nm (13 lbf.ft).
15.Tighten PAS rack fluid return pipe union to 22
Nm (16 lbf.ft).
16.Tighten fluid pipe bracket to 10 Nm (7 lbf.ft).
17.Align PAS rack clamp and tighten bolt.
18.Align pipes to clamp fit bolt and tighten to 10
Nm (7 lbf.ft).
19.Fit pinch bolt to steering column and tighten to
32 Nm (24 lbf.ft).
CAUTION: Nuts and bolts must be tightened
with the weight of the vehicle on the
suspension.20.Ensure tapers in track rod end and steering arm
are clean and rubber boot is not damaged.
21.Fit ball joints to steering arms, fit new nuts and
tighten to 55 Nm (40 lbf.ft).
22. KV6 models: Align coolant rail to cylinder
block, fit bolts and tighten to 10 Nm (7 lbf.ft).
23. KV6 models: Position heat shield, fit nuts and
tighten to 25 Nm (18 lbf.ft)
24. Td4 manual models: Align IRD hose 'P' clip fit
bolt and tighten to 25 Nm (18 lbf.ft).
25. Td4 manual models: Align gearchange
linkage to bulkhead, fit bolts and tighten to 25
Nm (18 lbf.ft).
26. Td4 manual models: Connect gear change
rods to gear change linkage.
27. Td4 auto models:Align IRD hose 'P' clip fit bolt
and tighten to 25 Nm (18 lbf.ft).
28.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
29.Remove stands and lower vehicle.
30.Bleed PAS system.

+ STEERING, ADJUSTMENTS, Power
assisted steering (PAS) system - bleed.
31.Check and adjust front wheel alignment.

+ STEERING, ADJUSTMENTS, Front
wheel alignment - check & adjust.