2001 LAND ROVER FREELANDER air condition

AIR CONDITIONING
82-16REPAIRS
Evaporator
$% 82.25.20
Remove
1.Depressurise A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
2.Remove bolt securing pipes to TXV valve.
3.Release both pipes from TXV valve.
4.Remove and discard 2 'O' rings from pipes.
CAUTION: Immediately cap all A/C pipes to
prevent ingress of dirt and moisture into the
system.
5.Remove fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
6.Remove bolt from face level ducting and
remove ducting.7.Disconnect 3 multiplugs from A/C switches and
heater harness.
8.Remove 2 nuts securing evaporator to body.
9.Release evaporator from drain hose and air
intake, remove evaporator assembly.
10.Release harness from evaporator securing
clips.
11.Remove 7 screws from evaporator casing and
remove top half of casing.
M820798
M820824

AIR CONDITIONING
REPAIRS 82-17
12.Remove evaporator from casing.
13.Remove 2 Allen key bolts securing TXV valve,
remove valve and discard 2 'O' rings.
Refit
1.Lubricate new 'O' rings with clean refrigerant oil
and fit to evaporator pipes
2.Fit evaporator pipes to TXV valve and fit
bracket, fit and tighten bolt to 10 Nm (7 lbf.ft).
3.Carefully fit evaporator to casing.
4.Fit top half of evaporator casing.
5.Fit 7 screws to casing.
6.Fit harness in securing clips.
7.Locate evaporator assembly to drain hose and
air intake, position evaporator to body.
8.Fit and tighten nuts securing evaporator to
body.
9.Connect multiplugs to heater harness and A/C
switches.
10.Position face level vent ducting, fit and tighten
bolt.
11.Fit fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
12.Clean evaporator pipes.
13.Lubricate new 'O' rings with refrigerant oil.
14.Fit 'O' rings to evaporator pipes.
15.Clean evaporator pipes.
16.Fit pipes to TXV valve and fit bracket, tighten
bolt to 10 Nm (7 lbf.ft).
17.Charge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
M820825

CHARGING AND STARTING
REPAIRS 86-1-3
REPAIRS
Alternator - Td4
$% 86.10.02
Remove
1.Disconnect battery earth lead.
2.Drain cooling system.

+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.
3. Models with A/C: Remove compressor drive
belt.

+ AIR CONDITIONING, REPAIRS,
Drive belt - compressor - Td4.
4.Remove 3 bolts securing coolant rail to sump
and cylinder block.
CAUTION: Care must be taken to ensure
that oil or fluid does not enter or
contaminate the alternator.
5. Models with A/C: Loosen bolt securing
compressor support bracket to sump, do not
remove.
6. Models with A/C: Remove 3 bolts securing
compressor to mounting bracket, release
support bracket and tie compressor aside.7. Models with A/C: Remove 3 bolts and bracket,
securing compressor mounting to casting on
cylinder block.
8.Disconnect alternator multiplug.
9.Remove nut securing battery cable to alternator
and remove cable.
10.Remove 3 bolts and remove alternator.
M86 5309
M86 5311

CHARGING AND STARTING
86-1-4 REPAIRS
Refit
1.Clean alternator mounting points.
2.Fit alternator to mounting bracket.Tighten M10
bolt to 45 Nm (33 lbf.ft) and M8 bolts to 25 Nm
(18 lbf.ft).
CAUTION: Ensure upper bolt is fitted prior
to assembly.
3.Connect alternator multiplug.
4.Fit battery cable to alternator terminal and
tighten to 10 Nm (7.5 lbf.ft).
5. Models with A/C: Clean A/C compressor and
housing mating faces, dowels and dowel holes.
6. Models with A/C: Fit bolts and compressor
mounting to casting, tighten to 25 Nm (18 lbf.ft).
7. Models with A/C: Position A/C compressor, fit
bolts and tighten to 25 Nm (18 lbf.ft).
8. Models with A/C: Align compressor support
bracket to sump and tighten bolt to 10 Nm (7.5
lbf.ft).
9.Fit lower coolant rail to sump and tighten bolts
to 10 Nm (7.5 lbf.ft).
10.Fit compressor drive belt.

+ AIR CONDITIONING, REPAIRS,
Drive belt - compressor - Td4.
11.Refill cooling system.

+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.
12.Connect battery earth lead.