2001 LAND ROVER FREELANDER ECU

HEATING AND VENTILATION
REPAIRS 80-3
Servo - air recirculation
$% 80.10.18
Remove
1.Remove glove box.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Glove box.
2.Disconnect multiplug from servo.
3.Remove screw securing servo to evaporator
and remove servo.
Refit
1.Fit servo to evaporator and secure with screw.
2.Connect multiplug to servo.
3.Fit glove box.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Glove box.
Switch - recirculation control
$% 80.10.21
Remove
1.Remove 3 heater control knobs.
2.Remove 2 screws securing heater control
finisher to heater controls and remove finisher.
3.Release switch and disconnect multiplug.
4.Remove switch.
Refit
1.Fit recirculation switch to heater control panel
and connect multiplug.
2.Fit heater control finisher to heater controls and
secure with screws.
3.Fit heater control knobs.

HEATING AND VENTILATION
80-4REPAIRS
Switch - fan - front heater
$% 80.10.22
Remove
1.Remove front console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - front - up to 04MY.
2.Disconnect multiplug from switch.
3.Remove drive shaft from switch.4.Remove 2 screws securing switch to heater
controls.
5.Remove switch.
Refit
1.Fit switch to heater controls and secure with
screws.
2.Fit drive shaft to switch.
3.Connect multiplug to switch.
4.Fit front console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - front - up to 04MY.

HEATING AND VENTILATION
80-6REPAIRS
Plenum - air intake
$% 80.15.62
Remove
1.Remove both wiper arms.

+ WIPERS AND WASHERS, REPAIRS,
Arm - wiper - each.
2.Remove 6 studs securing rear edge of air
intake moulding.
3.Remove air intake moulding and bonnet
sealing rubber.
NOTE: Do not carry out further dismantling if
component is removed for access only.
4.Remove bonnet sealing rubber from air intake
moulding.
5.Remove 4 clips securing air intake filter
retainers. Remove retainers and filters.Refit
1.Fit filters and retainers to air intake moulding
and secure with clips.
2.Fit bonnet sealing rubber to air intake moulding.
3.Fit air intake moulding and secure with studs.
4.Fit wiper arms.

+ WIPERS AND WASHERS, REPAIRS,
Arm - wiper - each.

HEATING AND VENTILATION
REPAIRS 80-7
Heater unit
$% 80.20.01
Remove
1.Drain cooling system.

+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.

+ COOLING SYSTEM - K SERIES 1.8,
ADJUSTMENTS, Coolant - drain & refill.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
2.Release 2 clips securing heater hoses to heater
and disconnect hoses.
3.Remove fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
4.Remove 2 bolts from console support bracket,
release 2 relays and remove bracket. Up to
03MY illustrated.5.Disconnect 4 multiplugs from heater controls.
Up to 04MY illustrated.
6.Disconnect multiplug from heater and release
diagnostic socket.
7. Models with A/C: Disconnect multiplug from
evaporator.
8.Remove bolt from duct of LH outer face level
vent and release duct from heater.

HEATING AND VENTILATION
80-8REPAIRS
9. NOTE: Models with passenger airbag,
remove carrier.Remove bolt from duct of RH
outer face level vent and release duct from
heater.
10.Release duct of RH demister vent.
11.Release duct of LH demister vent.
12.Release air inlet connector hose.
13.Release harness from 2 clips on heater.
14.Remove 2 nuts and 1 bolt securing heater to
body and remove heater.
NOTE: Do not carry out further dismantling if
component is removed for access only.15.Disconnect 2 multiplugs from heater controls.
16.Release air blend control cable from lever and
abutment.
17.Release air distribution cable from lever and
abutment.
18.Remove heater controls.

HEATING AND VENTILATION
REPAIRS 80-9
Refit
1.Position heater controls to replacement heater.
2.Connect air distribution cable to lever and
abutment.
3.Connect air blend cable to lever and abutment.
4.Connect multiplugs to heater controls.
5.Fit heater and secure with nuts and bolt.
6.Position harness and connect to clips on
heater.
7.Fit air inlet connector hose.
8.Fit RH demister vent duct to heater.
9. Models with passenger airbag, fit carrier.Fit
RH outer face level vent duct to heater and
secure to body with bolt.
10.Fit LH demister vent duct to heater.
11.Fit LH outer face level vent duct to heater and
secure to body with bolt.
12. Models with A/C: Connect multiplug to
evaporator.
13.Connect multiplug to heater and secure
diagnostic socket.
14.Connect multiplugs to heater controls.
15.Fit console support bracket and secure with
bolts.
16.Fit relays to console support bracket.
17.Fit fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
18.Connect heater hoses and secure with clips.
19.Refill cooling system.

+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.

+ COOLING SYSTEM - K SERIES 1.8,
ADJUSTMENTS, Coolant - drain & refill.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.

HEATING AND VENTILATION
REPAIRS 80-11
Harness - positive temperature co-
efficient (PTC) heater - Td4 models
$% 80.20.06
Remove
1.Disconnect battery earth lead.
2.Remove bolt securing PTC cable from positive
side of battery.
3.Remove ECM from 'E' box.

+ ENGINE MANAGEMENT SYSTEM -
EDC, REPAIRS, Engine control module
(ECM).
4.Disconnect multiplugs from gearbox ECU and
cooling fan sensor5.Release harness from cable ties and release
relays from inner casing.
6.Release and disconnect cooling fan and joint
harness multiplugs.
7.Release 3 harnesses and air duct rubber
sleeve's from housing.
8.Release clips and remove fuse box cover.
9.Remove nut securing ECM housing.
10.Release housing from retaining brackets and
remove.
M80 0557

HEATING AND VENTILATION
80-12REPAIRS
11.Remove 3 nuts securing fuse box, place fuse
box aside.
12.Release PTC harness from ECM housing
bracket.
13.Remove cover from PTC positive lead fuse
holder.
14.Release multiplug and disconnect PTC
harness from engine harness.
15.Remove 2 nuts securing both leads from (80
amp) fuse holder, remove leads.
16.Release clip securing PTC harness to ECM
housing bracket.17.Release PTC harness relay from bulkhead
retaining bracket.
18.Remove fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
19.Release and remove RH demister vent duct
20.Release and remove air duct.