2001 LAND ROVER FREELANDER fuse

ENGINE - K SERIES KV6
12-3-34 REPAIRS
38.With assistant depressing the brake pedal,
tighten front hub nuts to 400 Nm (295 lbf.ft).
39.Stake nut to shaft.
40.Fit front road wheels, fit and tighten nuts to 115
Nm (85 lbf.ft).
41.Lower vehicle on ramp.
42.Connect brake servo vacuum hose to inlet
manifold chamber.
43.Connect coolant hose to underside of
expansion tank and secure with clip.
44.Connect expansion tank hose to inlet manifold
and secure clip.
45.Connect top hose to radiator and secure with
clip. Position hose in bracket.
46.Connect heater feed and return hoses and
secure with clips.
47.Connect throttle inner cable to throttle cam and
secure outer cable in abutment bracket, if fitted.
48.Secure throttle cable in clips on harness
brackets, if fitted.
49.Adjust throttle cable, if fitted.

+ FUEL DELIVERY SYSTEM -
PETROL, ADJUSTMENTS, Throttle cable -
check and adjust - KV6.
50.Connect hose to purge control valve.
51.Connect fuel hose to fuel rail pipe, fit rubber
sleeve over hose connector.
52.Connect gearbox harness multiplugs and
secure multiplugs in mounting bracket clips.
53.Connect Lucar connector to starter solenoid.
54.Position earth lead to gearbox housing, fit and
tighten bolt to 25 Nm (18 lbf.ft).
55.Position engine harness to 'E' box mounting
bracket and secure with clips.
56.Connect earth header multiplug.
57.Connect multiplug to underbonnet fuse box.
58.Position battery and starter motor lead to
underbonnet fuse box, fit and tighten bolts to 8
Nm (6 lbf.ft).
59.Fit underbonnet fuse box cover.
60.Position 'E' box, secure in retaining clip, fit and
tighten nut to 9 Nm (7 lbf.ft).
61.Position carrier in 'E' box and secure with clips.
62.Position and secure air duct and harness
rubber sleeve in 'E' box.
63.Connect multiplugs securing main harness to
engine harness.
64.Position ECM harness and multiplug to 'E' box,
align harness clamp and secure screws to 'E'
box.
65.Fit engine ECM.

+ ENGINE MANAGEMENT SYSTEM -
SIEMENS, REPAIRS, Engine control module
(ECM) - Non NAS.
66.Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.67.Fill cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
68.Connect battery earth lead.
69.Fill gearbox with fluid.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.
70.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.

ENGINE - K SERIES KV6
12-3-36 REPAIRS
17.Rotate heated front screen relay anti-clockwise
and release it from 'E' box bracket.
18.Release 4 clips and remove carrier from 'E' box.
19.Remove nut, release retainer and remove 'E'
box.20.Remove engine compartment fuse box cover.
21.Remove 2 bolts securing battery and starter
lead to fuse box.
22.Disconnect multiplug from fuse box.
23.Disconnect earth header multiplug.
24.Release 3 clips securing engine harness to 'E'
box mounting bracket, lay harness over engine.
M12 6765
M12 6766

ENGINE - K SERIES KV6
12-3-44 REPAIRS
35.Fit rear beam.

+ FRONT SUSPENSION, REPAIRS,
Rear beam.
36.Fill IRD to correct level with fluid.

+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) lubrication system -
drain & refill - NAS.
37.Fit exhaust front pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Front pipe - NAS.
38.With assistant depressing the brake pedal,
tighten front hub nuts to 400 Nm.
39.Stake nuts to drive shafts
40.Fit front road wheels, fit and tighten nuts to 115
Nm.
41.Lower vehicle on lift.
42.Connect brake servo vacuum hose to inlet
manifold chamber.
43.Connect coolant hose to underside of
expansion tank and secure with clip.
44.Connect expansion tank hose to inlet manifold
and secure clip.
45.Connect top hose to radiator and secure with
clip. Position hose in bracket.
46.Connect heater feed and return hoses and
secure with clips.
47.Connect throttle inner cable to throttle cam and
secure outer cable in abutment bracket.
48.Connect hose to purge valve.
49.Fit purge hose into clip.
50.Connect fuel hose to fuel rail pipe, fit rubber
sleeve over hose connector.
51.Connect gearbox harness multiplugs and
secure multiplugs in mounting bracket clips.
52.Connect Lucar connector to starter solenoid.
53.Position earth lead to gearbox housing, fit and
tighten bolt to 25 Nm.
54.Position engine harness to 'E' box mounting
bracket and secure with clips.
55.Connect earth header multiplug.
56.Connect multiplug to under bonnet fuse box.
57.Position battery and starter motor lead to under
bonnet fuse box, fit and tighten bolts to 8 Nm.
58.Fit under bonnet fuse box cover.
59.Position 'E' box, secure in retaining clip, fit and
tighten nut to 9 Nm.
60.Fit carrier to 'E' box.
61.Fit air ducting to 'E' box.
62.Fit body harness to 'E' box, secure grommet
and harness clip.
63.Connect 'E' box cooling fan multiplug.
64.Connect multiplug to 'E' box temperature
sensor.
65.Connect multiplug to gearbox ECU.
66.Position engine harness to 'E' box and secure
grommet.67.Fit engine harness clamp and secure with
screws.
68.Connect engine harness multiplug to body
harness multiplug and fit multiplug to 'E' box.
69.Fit heated front screen harness to battery
positive cable and tighten bolt to 15 Nm (11
lbf.ft).
70.Fit engine ECM.

+ ENGINE MANAGEMENT SYSTEM -
SIEMENS, REPAIRS, Engine control module
(ECM) - fuel - NAS.
71.Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
72.Fill cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
73.Connect the battery earth lead.
74.Fill gearbox with fluid.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.
75.Fit the engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
76.Untie and close bonnet.

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-17
Relay - fuel pump
$% 19.22.39
Remove
1.Open engine compartment fuse box.
2.Identify and remove fuel pump relay.
Refit
1.Fit fuel pump relay.
2.Close engine compartment fuse box.
Throttle housing - K1.8
$% 19.22.45
Remove
1.Disconnect battery earth lead.
2.Remove clip and disconnect air intake hose
from throttle housing.
3.Release 4 clips and remove lid from air cleaner.

STEERING
57-20 REPAIRS
5.Lower glove lid and remove fuse box cover.
6.Carefully cut 2 harness clips from LH side of
column and release harness.
7.Release 2 harness clips from RH side of
column and release harness.
8. Models with automatic transmission:
Release key interlock cable from column clip.9. Models with automatic transmission:
Loosen union and release key interlock cable
from column lock.
10. Models with automatic transmission:
Remove bolt securing steering column height
adjuster lever and remove lever.
11. Models with automatic transmission:
Remove nut securing height adjuster clamp
bolt and remove bolt.
12. Models with automatic transmission:
Release key interlock cable from steering
column.
13. Models with automatic transmission: Fit
clamp bolt and nut to retain support bracket in
position.

STEERING
REPAIRS 57-21
14.Remove pinch bolt securing steering column to
PAS rack pinion.
15.Remove bolt securing steering column to
fusebox support bracket.
16.Remove 2 nuts and 2 bolts securing steering
column to fascia support rail.
17.Collect snubber.
18.Release steering column from support bracket
and PAS rack pinion.
19.Remove steering column assembly.
20.Remove 2 cable ties from steering column.
21.Remove key interlock cable clip.22.Remove 2 screws securing ignition switch and
remove ignition switch.
23.Remove passive coil.
24.Position steering column assembly in a vice.
25.Centre punch or drill out steering lock shear
bolts.
CAUTION: If steering column is to be re-
used, take care not to deform or damage
column in vice.
26.Remove steering column lock.
CAUTION: Take care not to damage steering
lock body if the lock is to be refitted.

STEERING
57-22 REPAIRS
Refit
1.Remove column from vice.
2.Fit new cable ties to steering column.
3. Models with automatic transmission: Fit key
interlock cable clip.
4.Position steering column to vehicle, locate
steering column on PAS rack, aligning column
coupling with PAS rack input flag.
5.Locate steering column on studs fit nuts but do
not tighten at this stage.
6.Fit bolts and snubber to pivot mountings and
tighten bolts to 14 Nm (10 lbf.ft).
7.Tighten nuts to 14 Nm (10 lbf.ft).
8.Fit and tighten PAS rack pinion clamp bolt to 32
Nm (24 lbf.ft).
CAUTION: Nuts and bolts must be tightened
with weight of vehicle on suspension.
9. Models with automatic transmission:
Remove clamp bolt from height adjuster and
position key interlock cable.
10. Models with automatic transmission: Fit
height adjuster clamp bolt and tighten nut to 10
Nm (7.5 lbf.ft). Ensure bolt and plastic stop are
correctly located in slot in column bracket.
11. Models with automatic transmission: Fit
height adjuster lever and tighten bolt 12 Nm (9
lbf.ft). Ensure lever is in the fully up position
before tightening bolt. Hold clamp bolt nut to
prevent nut rotation.
12. Models with automatic transmission:
Remove starter key from column lock.
13. Models with automatic transmission: Align
key interlock cable to column lock and tighten
union to 4 Nm (3 lbf.ft).
14. Models with automatic
transmission:Position lock to steering column
assembly and fit shear bolts. Do not tighten
shear bolts at this stage.
15. Models with automatic transmission: Insert
starter key, check operation of steering lock
and that key turns freely.
16. Models with automatic transmission:
Ensure correct operation of key interlock cable.
17. Models with automatic transmission:
Remove starter key from column lock.
18. Models with automatic transmission:
Tighten shear bolts fully and shear heads off.
19. Models with automatic transmission: Fit
passive coil.
20. Models with automatic transmission:
Position ignition switch to column, fit and
tighten screws.
21. Models with automatic transmission:
Secure key interlock cable in clip.
22. Models with automatic transmission:
Ensure key interlock cable is correctly fitted.23.Fit side support bolt and tighten to 10 Nm (7.5
lbf.ft).
24.Position harness and secure cable ties.
25.Fit fusebox cover and close glove box lid.
26.Connect multiplugs to column switch and
passive coil.
27.Fit aperture trim and secure with screws.
28. Fit steering column multi purpose switch.

+ LIGHTING, REPAIRS, Switch -
combined direction indicator/headlight/
horn.
29.Connect battery earth lead.

FRONT SUSPENSION
60-8 REPAIRS
9.Remove upper nut from anti-roll bar link,
release link and position aside.
CAUTION: Use a spanner and an Allen key
to prevent ball joint rotating when undoing
link.
10.Remove 2 nuts and bolts securing hub to
damper.
11.Release damper from hub.12. LH side: Remove 2 bolts securing positive and
negative leads to fusebox.
13. LH side: Disconnect multiplug from engine
compartment fuse box.
14. LH side: Release leads and position aside.
15. LH side: Remove 3 nuts securing fusebox and
position fusebox aside.
16. RH side: Remove bolt securing coolant
reservoir and position reservoir aside.
17.Reference mark top mounting in relationship to
body.
18.Remove 3 nuts from damper top mounting and
remove spring and damper assembly.