2001 LAND ROVER FREELANDER brake light

BRAKES
REPAIRS 70-11
Cable - handbrake
$% 70.35.25
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel(s).
3.Release rear ash tray, disconnect connector
from cigar lighter and remove ash tray.
4.Remove cable adjusting nut.
5.Remove 2 bolts securing cable retaining plate
to body and remove plate.
6.Release equalizer from adjusting rod.
7.Release cable from equalizer plate.
8.Remove 2 bolts securing cable to body and
subframe.
9.Release cable from chassis clip.10.Release cable grommet from floor and pull
cable from interior.
11.Remove rear brake shoes.

+ BRAKES, REPAIRS, Brake Shoes -
rear set.
12.Using tool LRT-70-007 release cable retainer
from backplate and withdraw cable from
vehicle.

BRAKES
70-12 REPAIRS
Refit
1.Manoeuvre cable into position and secure floor
grommet.
2.Fit and secure handbrake cable to backplate.
3.Fit brake shoes.

+ BRAKES, REPAIRS, Brake Shoes -
rear set.
4.Align cable clips, fit bolts and tighten to 22 Nm
(16 lbf.ft).
5.Secure cable in chassis clip.
6.Connect handbrake cable to equalizer.
7.Ensure spring is in place and fit equalizer to
adjusting rod.
8.Fit cable adjusting nut.
9.Fit cable retaining plate, fit bolts and tighten to
22 Nm (16 lbf.ft).
10.Adjust handbrake cable.

+ BRAKES, ADJUSTMENTS, Cable -
handbrake - check and adjust.
11.Fit ash tray and cigar lighter to rear console.
12.Fit road wheel(s).
13.Remove stands and lower vehicle.
Switch - handbrake warning
$% 70.35.40
Remove
1.Remove rear console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - rear.
2.Disconnect Lucar from handbrake warning
switch.
3.Release switch from handbrake.
Refit
1.Fit switch to handbrake and connect Lucar.
2.Fit rear console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - rear.

BRAKES
REPAIRS 70-13
Switch - stop light
$% 70.35.42
Remove
1.Disconnect brake light switch multiplug.
2.Release bayonet fitting on brake light switch
and remove switch.
Refit
1.Position switch and secure bayonet fitting.
2.Connect brake light switch multiplug.
3.Depress and hold brake pedal.
4.Reset switch by pulling plunger fully out.
5.Release brake pedal slowly to set switch
adjustment.
Sensor - brake pedal position
$% 70.35.44
Remove
1.Release bayonet fitting on brake light switch
and remove switch.
2.Release sensor from mounting bracket.
3.Disconnect sensor multiplug and remove
sensor.
4.Remove sensor mounting from bracket.
Refit
1.Position sensor to mounting bracket and
connect multiplug.
2.Position switch and secure bayonet fitting.
3.Hold brake pedal depressed and push sensor
fully into bracket, release pedal slowly to set
sensor position.

PANEL REPAIRS
77-2-30 REPAIRS
Front sidemember (complete)
In this procedure, the front sidemember closing
panel and the related crossmember to sidemember
gusset plate are replaced in conjunction with the front
sidemember.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
6.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
7.Remove front bumper armature.
8.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
9.Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
10.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
11.Release wiring to headlamp and position aside.
12.Remove engine bay shield.
13.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
14.Remove front suspension rear beam.
15.Remove engine and gearbox.

+ ENGINE - K SERIES KV6, REPAIRS,
Engine and automatic gearbox - up to 03MY.
16.Remove PAS rack.

+ STEERING, REPAIRS, Power
steering rack.
17.Remove fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
18. LH side: Remove front bumper LH support
bracket.
19. LH side: Remove LH engine mounting from
body.
20. LH side: Remove battery.

+ CHARGING AND STARTING,
REPAIRS, Battery.
21. LH side: Remove air intake hose.
22. LH side: Remove horn.

+ SECURITY, REPAIRS, Horn.
23. RH side: Remove front bumper RH support
bracket.24. RH side: Remove RH engine mounting from
body.
25. RH side: Remove windscreen washer
reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
26. Driver's side: Remove passenger
compartment fuse box.
27. Driver's side: Remove brake pedal box and
brake servo.
28. Driver's side: Remove clutch pedal box.
29.Remove treadplate from front door aperture.
Release front carpet and position aside.
30.Remove insulation pads from engine bulkhead.

PANEL REPAIRS
REPAIRS 77-2-31
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.
Refit
1.Fit insulation pads to engine bulkhead.
2.Position front carpet and fit treadplate to front
door aperture. 3. Driver's side: Fit clutch pedal box.
4. Driver's side: Fit brake pedal box and brake
servo.
5. Driver's side: Fit passenger compartment fuse
box.
6. LH side: Fit horn.

+ SECURITY, REPAIRS, Horn.
7. LH side: Fit air intake hose.
8. LH side: Fit battery. Do not connect battery
earth lead.

+ CHARGING AND STARTING,
REPAIRS, Battery.
9. LH side: Fit LH engine mounting to body.
10. LH side: Fit front bumper LH support bracket.
11. RH side: Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
12. RH side: Fit RH engine mounting to body.
13. RH side: Fit front bumper RH support bracket.
14.Fit fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
15.Fit PAS rack.

+ STEERING, REPAIRS, Power
steering rack.
16.Fit engine and gearbox.

+ ENGINE - K SERIES KV6, REPAIRS,
Engine and automatic gearbox - up to 03MY.
17.Fit front suspension rear beam.
18.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
19.Fit engine bay shield.
20.Fit headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
21.Secure headlamp wiring.
22.Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
23.Fit radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
24.Fit front bumper armature.
25.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
26.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
27.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
28.Connect all ECUs.
29.Connect alternator.
30.Connect battery earth lead.

PANEL REPAIRS
77-2-36 REPAIRS
Valance upper front
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
6.Remove front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
7.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
8.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
9.Release wiring from valance and position
aside.
10. LH side: Remove ECM.
11. LH side: Remove battery.

+ CHARGING AND STARTING,
REPAIRS, Battery.
12. RH side: Remove PAS fluid reservoir.
13. RH side: Remove brake pipes from valance.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown. Refit
1. LH side: Fit battery. Do not connect earth lead.

+ CHARGING AND STARTING,
REPAIRS, Battery.
2. LH side: Fit ECM.
3. RH side: Fit PAS fluid reservoir.
4. RH side: Fit brake pipes to valance. Bleed
brakes.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
5.Secure wiring to valance.
6.Fit headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
7.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
8.Fit front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
9.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
10.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
11.Connect all ECUs.
12.Connect alternator.
13.Connect battery earth lead.

PANEL REPAIRS
REPAIRS 77-2-37
Valance front
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
6.Remove engine bay shield.
7.Remove front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
8.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
9.Remove front bumper support bracket.
10.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
11.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
12.Release wiring to headlamp and position aside.
13. LH side: Remove air cleaner.
14. LH side: Remove air intake hose.
15. LH side: Remove ECM.
16. LH side: Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
17. LH side: Remove engine compartment fuse
box and related wiring.
18. LH side: Remove LH front brake pipe.
19. RH side: Remove PAS fluid reservoir.
20. RH side: Remove RH front brake pipe.
21. RH side: Remove windscreen washer
reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
22. RH side: Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.

PANEL REPAIRS
77-2-38 REPAIRS
Refit
1. LH side: Fit LH front brake pipe. Bleed brake
system.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
2. LH side: Fit engine compartment fuse box and
related wiring.
3. LH side: Fit battery carrier. Do not connect
battery earth lead.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
4. LH side: Fit ECM.
5. LH side: Fit air intake hose.
6. LH side: Fit air cleaner.
7. RH side: Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
8. RH side: Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
9. RH side: Fit RH front brake pipe. Bleed brake
system.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
10. RH side: Fit PAS fluid reservoir.
11.Fit headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
12.Secure headlamp wiring.
13.Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
14.Fit radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
15.Fit front bumper support bracket.
16.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
17.Fit front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
18.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
19.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
20.Connect all ECUs.
21.Connect alternator.
22.Connect battery earth lead.