2001 INFINITI QX4 Ignition harness

5 CHECK POWER SUPPLY-II
1. Disconnect ECM relay.
SEF681UB
2. Check voltage between ECM relay terminals 1, 5 and ground with CONSULT-II or tester.
SEF956Y
OK or NG
OK©GO TO 7.
NG©GO TO 6.
6 DETECT MALFUNCTIONING PART
Check the following.
I7.5A and 10A fuses
IHarness for open or short between ECM relay and battery
©Repair open circuit or short to ground or short to power in harness or connectors.
7 CHECK OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check harness continuity between ECM terminal 26 and ECM relay terminal 2.
Continuity should exist.
2. Also check harness for short to ground and short to power.
OK or NG
OK©Go to ªDTC P1320 IGNITION SIGNALº, EC-499.
NG©GO TO 8.
8 DETECT MALFUNCTIONING PART
Check the following.
IHarness connectors E1, M1 and M32, F23
IHarness for open or short between ECM relay and ECM
©Repair open circuit or short to ground or short to power in harness or connectors.
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
TROUBLE DIAGNOSIS FOR POWER SUPPLY
Main Power Supply and Ground Circuit (Cont'd)
EC-145

9 CHECK ECM POWER SUPPLY CIRCUIT-II
1. Stop engine.
2. Check voltage between ECM terminal 67 and ground with CONSULT-II or tester.
SEF293X
OK or NG
OK©GO TO 11.
NG©GO TO 10.
10 DETECT MALFUNCTIONING PART
Check the following.
IHarness connectors E1, M1 and M32, F23
IHarness for open or short between ECM and fuse
©Repair harness or connectors.
11 CHECK ECM POWER SUPPLY CIRCUIT-III
1. Turn ignition switch ªONº and then ªOFFº.
2. Check voltage between ECM terminals 110, 112 and ground with CONSULT-II or tester.
SEF294X
OK or NG
OK©GO TO 17.
NG (Battery voltage
does not exist.)©GO TO 12.
NG (Battery voltage
exists for more than a
few seconds.)©GO TO 14.
TROUBLE DIAGNOSIS FOR POWER SUPPLY
Main Power Supply and Ground Circuit (Cont'd)
EC-146

12 CHECK ECM POWER SUPPLY CIRCUIT-IV
1. Disconnect ECM relay.
SEF681UB
2. Check voltage between ECM relay terminal 7 and ground with CONSULT-II or tester.
SEF957Y
OK or NG
OK©GO TO 14.
NG©GO TO 13.
13 DETECT MALFUNCTIONING PART
Check the following.
IHarness for open or short between ECM relay and 7.5A fuse
©Repair open circuit or short to ground or short to power in harness or connectors.
14 CHECK ECM POWER SUPPLY-V
1. Turn ignition switch ªOFFº and then ªONº.
2. Check voltage between ECM terminal 12 and ground with CONSULT-II or tester.
SEF331Z
OK or NG
OK©GO TO 16.
NG©GO TO 15.
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
TROUBLE DIAGNOSIS FOR POWER SUPPLY
Main Power Supply and Ground Circuit (Cont'd)
EC-147

15 DETECT MALFUNCTIONING PART
Check the following.
IHarness connectors E1, M1
IHarness connectors M94, F27
I10A fuse
©Repair harness or connectors.
16 CHECK HARNESS CONTINUITY BETWEEN ECM RELAY AND ECM FOR OPEN AND SHORT
1. Check harness continuity between ECM terminals 110, 112 and ECM relay terminal 6.
Refer to WIRING DIAGRAM.
Continuity should exist.
2. Also check harness for short to ground and short to power.
OK or NG
OK©GO TO 18.
NG©GO TO 17.
17 DETECT MALFUNCTIONING PART
Check the following.
IHarness connectors E1, M1 and M32, F23
IHarness for open or short between ECM and ECM relay
©Repair open circuit or short to ground or short to power in harness or connectors.
18 CHECK ECM RELAY
1. Apply 12V direct current between ECM relay terminals 1 and 2.
2. Check continuity between relay terminals 3 and 5, 6 and 7.
SEF296X
OK or NG
OK©GO TO 19.
NG©Replace ECM relay.
19 CHECK ECM GROUND CIRCUIT FOR OPEN AND SHORT-II
1. Turn ignition switch ªOFFº.
2. Disconnect ECM harness connector.
3. Check harness continuity between ECM terminals 48, 57, 106, 108 and engine ground.
Refer to WIRING DIAGRAM.
Continuity should exist.
4. Also check harness for short to ground and short to power.
OK or NG
OK©GO TO 20.
NG©Repair open circuit or short to ground or short to power in harness or connectors.
TROUBLE DIAGNOSIS FOR POWER SUPPLY
Main Power Supply and Ground Circuit (Cont'd)
EC-148

On Board Diagnosis LogicNBEC0053Malfunction is detected when
(Malfunction A)an excessively high voltage from the sensor is
sent to ECM when engine is not running,
(Malfunction B)an excessively low voltage from the sensor is sent
to ECM when engine is running,
(Malfunction C)a high voltage from the sensor is sent to ECM
under light load driving condition,
(Malfunction D)a low voltage from the sensor is sent to ECM
under heavy load driving condition,
(Malfunction E)a voltage from the sensor is constantly approx.
1.0V when engine is running.
FAIL-SAFE MODENBEC0053S02When the malfunction B is detected, the ECM enters fail-safe mode
and the MIL lights up.
Detected items Engine operating condition in fail-safe mode
Mass air flow sensor circuit Engine speed will not rise more than 2,400 rpm due to the fuel cut.
Possible CauseNBEC0426MALFUNCTION A OR CNBEC0426S01IHarness or connectors
(The sensor circuit is open or shorted.)
IMass air flow sensor
MALFUNCTION B, D OR ENBEC0426S02IHarness or connectors
(The sensor circuit is open or shorted.)
IIntake air leaks
IMass air flow sensor
DTC Confirmation ProcedureNBEC0054Perform ªPROCEDURE FOR MALFUNCTION Aº first.
If the 1st trip DTC cannot be confirmed, perform ªPROCE-
DURE FOR MALFUNCTION B AND Eº.
If there is no problem on ªPROCEDURE FOR MALFUNCTION
B AND Eº, perform ªPROCEDURE FOR MALFUNCTION Cº.
If there is no problem on ªPROCEDURE FOR MALFUNCTION
Cº, perform ªPROCEDURE FOR MALFUNCTION Dº.
NOTE:
If ªDTC Confirmation Procedureº has been previously conducted,
always turn ignition switch ªOFFº and wait at least 10 seconds
before conducting the next test.
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0100 MASS AIR FLOW SENSOR (MAFS)
On Board Diagnosis Logic
EC-151

4 CHECK MAFS POWER SUPPLY CIRCUIT
1. Disconnect mass air flow sensor (MAFS) harness connector.
SEF960Y
2. Turn ignition switch ªONº.
3. Check voltage between MAFS terminals 2, 4 and ground with CONSULT-II or tester.
SEF297X
OK or NG
OK©GO TO 6.
NG©GO TO 5.
5 DETECT MALFUNCTIONING PART
Check the following.
IHarness for open or short between ECM relay and mass air flow sensor
IHarness for open or short between mass air flow sensor and ECM
©Repair harness or connectors.
6 CHECK MAFS GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch ªOFFº.
2. Disconnect ECM harness connector.
3. Check harness continuity between MAFS terminal 3 and ECM terminal 73.
Refer to Wiring Diagram.
Continuity should exist.
4. Also check harness for short to power.
OK or NG
OK©GO TO 7.
NG©Repair open circuit or short to power in harness or connectors.
DTC P0100 MASS AIR FLOW SENSOR (MAFS)
Diagnostic Procedure (Cont'd)
EC-156

Possible CauseNBEC0728IHarness or connectors
(Absolute pressure sensor circuit is open or shorted.)
IAbsolute pressure sensor
DTC Confirmation ProcedureNBEC0729NOTE:
If ªDTC Confirmation Procedureº has been previously conducted,
always turn ignition switch ªOFFº and wait at least 10 seconds
before conducting the next test.
SEF058Y
WITH CONSULT-IINBEC0729S011) Turn ignition switch ªONº.
2) Select ªDATA MONITORº mode with CONSULT-II.
3) Wait at least 10 seconds.
4) If 1st trip DTC is detected, go to ªDiagnostic Procedureº,
EC-161.
WITH GSTNBEC0729S02Follow the procedure ªWITH CONSULT-IIº above.
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0105 ABSOLUTE PRESSURE SENSOR
Possible Cause
EC-159

Diagnostic ProcedureNBEC0731
1 RETIGHTEN GROUND SCREWS
1. Turn ignition switch ªOFFº.
2. Loosen and retighten engine ground screws.
SEF959Y
©GO TO 2.
2 CHECK ABSOLUTE PRESSURE SENSOR CONNECTOR FOR WATER
1. Disconnect absolute pressure sensor harness connector.
SEF961Y
2. Check sensor harness connector for water.
Water should not exist.
OK or NG
OK©GO TO 3.
NG©Repair or replace harness connector.
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0105 ABSOLUTE PRESSURE SENSOR
Diagnostic Procedure
EC-161