2001 INFINITI QX4 wiring diagram

Wiring DiagramNBEC0175RIGHT BANKNBEC0175S01
MEC955C
DTC P0172 (RIGHT, -B1), P0175 (LEFT, -B2) FUEL INJECTION SYSTEM
FUNCTION (RICH)
Wiring Diagram
EC-304

LEFT BANKNBEC0175S02
MEC956C
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0172 (RIGHT, -B1), P0175 (LEFT, -B2) FUEL INJECTION SYSTEM
FUNCTION (RICH)
Wiring Diagram (Cont'd)
EC-305

Diagnostic ProcedureNBEC0176
1 CHECK EXHAUST AIR LEAK
1. Start engine and run it at idle.
2. Listen for an exhaust air leak before three way catalyst.
SEF099P
OK or NG
OK©GO TO 2.
NG©Repair or replace.
2 CHECK FOR INTAKE AIR LEAK
Listen for an intake air leak after the mass air flow sensor.
OK or NG
OK©GO TO 3.
NG©Repair or replace.
3 CHECK HEATED OXYGEN SENSOR 1 (FRONT) CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch ªOFFº.
2. Disconnect corresponding heated oxygen sensor 1 (front) harness connector.
3. Disconnect ECM harness connector.
4. Check harness continuity between ECM terminal and HO2S1 terminal as follows.
Refer to Wiring Diagram.
MTBL0479
Continuity should exist.
5. Check harness continuity between ECM terminal or HO2S1 terminal and ground as follows.
Refer to Wiring Diagram.
MTBL0480
Continuity should not exist.
6. Also check harness for short to power.
OK or NG
OK©GO TO 4.
NG©Repair open circuit or short to ground or short to power in harness or connectors.
DTC P0172 (RIGHT, -B1), P0175 (LEFT, -B2) FUEL INJECTION SYSTEM
FUNCTION (RICH)
Diagnostic Procedure
EC-306

Wiring DiagramNBEC0180
MEC957C
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0180 FUEL TANK TEMPERATURE SENSOR
Wiring Diagram
EC-311

Diagnostic ProcedureNBEC0181
1 CHECK FUEL TANK TEMPERATURE SENSOR POWER SUPPLY CIRCUIT
1. Turn ignition switch ªOFFº.
2. Disconnect fuel level sensor unit and fuel pump harness connector.
SEF751UA
3. Turn ignition switch ªONº.
4. Check voltage between fuel level sensor unit terminal 1 and ground with CONSULT-II or tester.
SEF973Y
OK or NG
OK©GO TO 3.
NG©GO TO 2.
2 DETECT MALFUNCTIONING PART
Check the following.
IHarness connectors B1, M2
IHarness connectors M92, F27
IHarness for open or short between ECM and fuel level sensor unit and fuel pump
©Repair harness or connector.
3 CHECK FUEL TANK TEMPERATURE SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch ªOFFº.
2. Check harness continuity between fuel level sensor unit and fuel pump terminal 2 and body ground. Refer to Wiring
Diagram.
Continuity should exist.
3. Also check harness for short to power.
OK or NG
OK©GO TO 4.
NG©Repair open circuit or short to power in harness or connectors.
DTC P0180 FUEL TANK TEMPERATURE SENSOR
Diagnostic Procedure
EC-312

Wiring DiagramNBEC0189
MEC958C
DTC P0325 KNOCK SENSOR (KS)
Wiring Diagram
EC-330

Diagnostic ProcedureNBEC0190
1 CHECK KNOCK SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-I
1. Turn ignition switch ªOFFº.
2. Disconnect ECM harness connector.
3. Check resistance between ECM terminal 93 and engine ground.
NOTE:
It is necessary to use an ohmmeter which can measure more than 10 MW.
SEF321X
4. Also check harness for short to ground and short to power.
OK or NG
OK©GO TO 5.
NG©GO TO 2.
2 CHECK KNOCK SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-II
1. Disconnect knock sensor harness connector.
2. Check harness continuity between ECM terminal 93 and knock sensor terminal 2. Refer to Wiring Diagram.
Continuity should exist.
3. Also check harness for short to ground and short to power.
OK or NG
OK©GO TO 4.
NG©GO TO 3.
3 DETECT MALFUNCTIONING PART
Check the following.
IHarness connectors F19, F116
IHarness for open or short between ECM and knock sensor
©Repair open circuit or short to ground or short to power in harness or connectors.
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0325 KNOCK SENSOR (KS)
Diagnostic Procedure
EC-331

4 CHECK KNOCK SENSOR
Check resistance between knock sensor terminal 2 and ground.
NOTE:
It is necessary to use an ohmmeter which can measure more than 10 MW.
SEF976Y
CAUTION:
Do not use any knock sensors that have been dropped or physically damaged. Use only new ones.
OK or NG
OK©GO TO 8.
NG©Replace knock sensor.
5 RETIGHTEN GROUND SCREWS
Loose and retighten engine ground screws.
SEF959Y
©GO TO 6.
6 CHECK KNOCK SENSOR SHIELD CIRCUIT FOR OPEN AND SHORT
1. Disconnect harness connectors F19, F116.
2. Check harness continuity between harness connector F19 terminal 1 and engine ground. Refer to Wiring Diagram.
Continuity should exist.
3. Also check harness for short to power.
OK or NG
OK©GO TO 8.
NG©GO TO 7.
7 DETECT MALFUNCTIONING PART
Check the following.
IHarness connectors F19, F116
IHarness for open or short between harness connector F19 and engine ground
©Repair open circuit or short to power in harness or connectors.
DTC P0325 KNOCK SENSOR (KS)
Diagnostic Procedure (Cont'd)
EC-332