2001 HONDA ACCORD SEDAN ignition

Indicator Lights

The instrument panel has many

indicators to give you important
information about your car.

Seat Belt Reminder Light
This indicator lights when you turn
the ignition switch ON (II). It is a
reminder to you and your passengers
to protect yourselves by fastening
the seat belts. A beeper also sounds
if you have not fastened your seat

belt.

If you do not fasten your seat belt,
the beeper will stop after a few
seconds but the light stays on until
you do. Both the light and the beeper
stay off if you fasten your seat belt
before turning on the ignition.
Low Oil Pressure

Indicator

The engine can be severely damaged
if this light flashes or stays on when

the engine is running. For complete

information, see page 309 .

Charging System

Indicator

If this light comes on when the

engine is running, the battery is not

being charged. For complete

information, see page 310 .

Instruments and Controls

Indicator Lights

U.S.

Parking Brake and
Brake System Indicator
1. This indicator comes on when you turn the ignition switch ON (II). It
is a reminder to check the parking
brake. Driving with the parking
brake not fully released candamage the brakes and tires.
2. If the indicator remains lit after you have fully released theparking brake while the engine isrunning, or if it comes on while
driving, it can indicate a problem
in the brake system. For complete
information, see page 313 .
Supplemental Restraint

System Indicator
This indicator lights when you turn the ignition switch ON (II). If itcomes on at any other time, it
indicates a potential problem with
your front airbags or automatic seat belt tensioners. This light willalso alert you to a potential problem
with your side airbags. For complete information, see page 47.
Side Airbag Indicator
Only on models equipped with side
airbags
This indicator lights when you turn the ignition switch ON (II). If itcomes on at any other time, it
indicates that the passenger's side airbag has automatically shut off.
For complete information, see page
47.

Malfunction IndicatorLamp

See page 311.
U.S.


Anti-lock Brake System
(ABS) Indicator

Only on models equipped with ABS (see

page 204)

This light normally comes on for a few seconds when you turn theignition switch ON (II), and when
the ignition switch is turned toSTART (III). If this light comes on at
any other time, there is a problem in
the ABS. If this happens, take the car to your dealer to have it checked.
With the light on, your car still has normal braking ability but no anti-
lock. For complete information, see
page 205.

Instruments and Controls

Canada

S R S
SIDEAIRBAG
A B S

Canada

Indicator Lights

Traction Control System(TCS) Indicator

On all V6 models

This indicator has three functions:
1. It comes on as a reminder that you have turned off the Traction
Control System.
2. It flashes when the TCS is regulating wheelspin.
3. If it comes on and stays on when the Traction Control System is on,it indicates that there is a problem
in the TCS.
This light also comes on when you turn the ignition ON (II) and goes offafter the engine starts. See page
206 for more information on the

TCS.
Door and Brake Lamp Monitor
The appropriate light comes on in this display if the trunk or any dooris not closed tightly. If a brake light does not work, the BRAKE LAMP
indicator comes on when you push
the brake pedal with the ignition switch ON (II).
A burned out brake light is a hazard when drivers behind you cannot tell
you are braking. Have your brakelights repaired right away.
All the lights in the monitor display
come on for a few seconds when you
turn the ignition switch ON (II). Turn Signal and
Hazard WarningIndicators
The left or right turn signal light blinks when you signal a lane changeor turn. If the light does not blink or
blinks rapidly, it usually means oneof the turn signal bulbs is burned out (see page 277 ). Replace the bulb as
soon as possible, since other drivers
cannot see that you are signalling.
When you turn on the Hazard
Warning switch, both turn signal lights blink. All turn signals on the
outside of the car should flash.
Instruments and Controls

TCS

Indicator Lights

"Daytime Running
Lights" Indicator

Canadian models only

This indicator lights when you turn the ignition switch to ON (II) withthe headlight switch off and the
parking brake set. It should go off if
you turn on the headlights or release
the parking brake. If it comes on at any other time, it means there is a
problem with the DRL. There may also be a problem with the high
beam headlights.
High Beam Indicator
This light comes on with the high beam headlights. See page 60 forinformation on the headlight
controls.
On Canadian models, this indicator
comes on with reduced brightness
when the Daytime Running Lights (DRL) are on (see page 63 ). Cruise Control Indicator

Only on models equipped with Cruise
Control System

This lights when you set the cruise control. See page 68 for information
on operating the cruise control.
Low Fuel Indicator
This light comes on as a reminder that you must refuel soon. Immobilizer System
Indicator
This indicator comes on for a few seconds when you turn the ignition
switch ON (II). It will then go off if
you have inserted a properly-coded ignition key. If it is not a properly-coded key, the indicator will blink
and the engine will not start (see
page 72 ).
This indicator also blinks several times when you turn the ignitionswitch from ON (II) to ACCESSORY (I) or LOCK (0).
Washer Level Indicator

Canadian models only

This light comes on when the
washer fluid level is low. Add washer fluid when you see this light come on (see page 246 ).
Instruments and Controls

CRUISE
CONTROL
DRL

Gauges

Trip Meter

This meter shows the number of miles (U.S.) or kilometers (Canada)driven since you last reset it.
There are two trip meters: Trip A and Trip B. Switch between these
displays by pressing the Select/
Reset button repeatedly. Each trip
meter works independently, so you
can keep track of two different

distances.

To reset a trip meter, display it and then press and hold the Select/Reset
button until the number resets to "0.0". Both trip meters will reset if
the vehicle's battery goes dead or isdisconnected. Temperature Gauge
This shows the temperature of the engine's coolant. During normal
operation, the pointer should rise
from the bottom white mark to about
the middle of the gauge. In severe driving conditions, such as very hot
weather or a long period of uphill driving, the pointer may rise to near
the upper grey zone. If it reaches the
red (Hot) mark, pull safely to the side of the road. Turn to page 239 for
instructions and precautions on
checking the engine's cooling
system.
Fuel Gauge
This shows how much fuel you have. It is most accurate when the car is on
level ground. It may show slightly
more or less than the actual amount
when you are driving on curvy or hilly roads.
4-cylinder models
The gauge stays at the same fuel level reading after you turn off the
ignition. When you add fuel, the
gauge slowly changes to the new reading after you turn the ignitionswitch back ON (II).

6-cylinder models

The needle returns to the bottom after you turn off the ignition. The
gauge shows the fuel level reading immediately after you turn the
ignition switch back ON (II).

Instruments and Controls

Gauges

Maintenance Required Indicator

This indicator reminds you that it is time to take your car in for
scheduled maintenance.

Refer to the Maintenance Schedules
for Normal and Severe Driving Conditions on pages 224 — 228.
For the first 6,000 miles (9,600 km)
after the Maintenance Required
Indicator is reset, it will come on for
two seconds when you turn the
ignition switch ON (II). Between 6,000 miles (9,600 km) and
7,500 miles (12,000 km) this
indicator will light for two seconds
when you first turn the ignition switch ON (II), and then flash for
ten seconds.
If you exceed 7,500 miles (12,000
km) without having the scheduled maintenance performed, this
indicator will remain on as a constant
reminder. Your dealer will reset this indicator
after completing the scheduled
maintenance. If this maintenance is done by someone other than your
Honda dealer, reset the indicator as

follows.

1. Turn off the engine.
2. Press and hold the select/reset button in the instrument panel,
then turn the ignition switch ON
(II).
3. Hold the buttons for about ten sec- onds, until the indicator resets.

Instruments and Controls
MAINTENANCE REQUIRED
INDICATOR

SELECT/RESET BUTTON

Controls Near the Steering Wheel

Headlights
The rotating switch on the left lever controls the lights. Turning this switch to the position turns
on the parking lights, taillights,
instrument panel lights, side-marker
lights, and rear license plate lights. Turning the switch to the
position turns on the headlights. If you leave the lights on with the
ignition switch in ACCESSORY (I)or LOCK (0), you will hear a
reminder chime when you open the driver's door.
To change between low beams and high beams, pull the turn signal lever
until you hear a click, then let go.
The blue high beam indicator will light (see page 58). To flash the high beams, pull the
turn signal lever back lightly, thenrelease it. The high beams will comeon and go off.
The high beams will stay on for as long as you hold the lever back, no
matter what position the headlightswitch is in.

Instruments and Controls

Controls Near the Steering Wheel

Automatic Lighting Off Feature
On EX and EX-V6 models

The Automatic Lighting Off feature turns off the headlights, parking
lights, taillights, side marker lights,license plate lights and instrument
panel lights within 15 seconds of
removing the key from the ignitionswitch and closing the driver's door.
This feature activates if you leave the headlight switch in the
or position, remove the key,
open, then close the driver's door.
If you remove the key from the
ignition switch with the headlight switch on, but do not open the door
and get out, the lights will turn off
after ten minutes.
The lights will turn on again when you unlock or open the driver's door.If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver's door open, you will hear a lights-on
reminder chime.
Daytime Running Lights

(Canadian Models)

With the headlight switch off, the high beam headlights come on with
reduced brightness when you turn
the ignition switch to ON (II) and
release the parking brake. They
remain on until you turn the ignitionoff, even if you set the parking brake.
The headlights revert to normal operation when you turn them on
with the switch. Instrument Panel Brightness
The knob on the instrument panel controls the brightness of the instru-
ment panel lights. Turn the knob to
adjust the brightness.
Instruments and Controls