2001 HONDA ACCORD COUPE dead battery

Gauges

Trip Meter

This meter shows the number of miles (U.S.) or kilometers (Canada)driven since you last reset it.
There are two trip meters: Trip A and Trip B. Switch between these
displays by pressing the Select/
Reset button repeatedly. Each trip
meter works independently, so you
can keep track of two different

distances.

To reset a trip meter, display it and then press and hold the Select/Reset
button until the number resets to "0.0". Both trip meters will reset if
the vehicle's battery goes dead or isdisconnected. Temperature Gauge
This shows the temperature of the engine's coolant. During normal
operation, the pointer should rise
from the bottom white mark to about
the middle of the gauge. In severe driving conditions, such as very hot
weather or a long period of uphill driving, the pointer may rise to near
the upper grey zone. If it reaches the
red (Hot) mark, pull safely to the side of the road. Turn to page 239 for
instructions and precautions on
checking the engine's cooling
system.
Fuel Gauge
This shows how much fuel you have. It is most accurate when the car is on
level ground. It may show slightly
more or less than the actual amount
when you are driving on curvy or hilly roads.
4-cylinder models
The gauge stays at the same fuel level reading after you turn off the
ignition. When you add fuel, the
gauge slowly changes to the new reading after you turn the ignitionswitch back ON (II).

6-cylinder models

The needle returns to the bottom after you turn off the ignition. The
gauge shows the fuel level reading immediately after you turn the
ignition switch back ON (II).

Instruments and Controls

HomeLink Universal Transmitter
On all V6 models

The HomeLink Universal
Transmitter built into your car can be programmed to operate remotely-controlled devices around your home,such as garage doors, lighting, or
home security systems. It can replace up to three remote
transmitters.

Customer Assistance

If you have problems with training
the HomeLink Universal

Transmitter, or would like
information on home products that
can be operated by the transmitter,

call (800) 355-3515. On the Internet,

go to www.homelink.jci.com. Important Safety Precautions
Always refer to the operating instructions and safety information
that came with your garage dooropener or other equipment you
intend to operate with the HomeLink Universal Transmitter. If you do not
have this information, you should contact the manufacturer of the
equipment.
While training or using the transmitter, make sure you have aclear view of the garage door or gate,
and that no one will be injured by its
movement.
General Information
If you are training the transmitter tooperate a garage door or gate, it is
recommended that you unplug the
motor for that device during training. Repeatedly pressing the remote
control button could burn out the
motor. The HomeLink transmitter stores
the code in a permanent memory.
There should be no need to retrain the transmitter if your car's battery
goes dead or is disconnected.
If your garage door opener was
manufactured before April 1982, you
may not be able to program the
HomeLink Universal Transmitter to
operate it. Garage door openers
manufactured before that date do
not have a safety feature that causes
them to stop and reverse if an
obstacle is detected during closing,
increasing the risk of injury. If you
have questions, call (800) 355-3515.
Instruments and Controls

Audio System

Preset — You can store the
frequencies of your favorite radiostations in the six preset buttons.
Each button will store one frequency on the AM band, and two
frequencies on the FM band.
To store a frequency:
1. Select the desired band, AM or FM. FM1 and FM2 let you store
two frequencies with each Preset

button.

2. Use the TUNE or SEEK function to tune the radio to a desired

station.

3. Pick the Preset button you want for that station. Press the buttonand hold it until you hear a beep.
4. Repeat steps 1 to 3 to store a total of six stations on AM and twelve
on FM.
AM/FM BUTTON

SEEK SWITCH

Once a station's frequency is stored,
simply press and release the proper
preset button to tune to it.
The preset frequencies will be lost if your car's battery goes dead, isdisconnected, or the radio fuse is

removed.

Comfort and Convenience Features
PRESET

BUTTONS

TUNE BAR

Audio System

Preset — You can store the
frequencies of your favorite radio stations in the six preset buttons.
Each button will store one frequency
on the AM band, and two
frequencies on the FM band.
To store a frequency:
1. Select the desired band, AM or FM. FM1 and FM2 let you store
two frequencies with each Preset

button.

2. Use the TUNE, SEEK, or SCAN function to tune the radio to adesired station.
3. Pick the Preset button you want for that station. Press the buttonand hold it until you hear a beep.
4. Repeat steps 1 to 3 to store a total of six stations on AM and twelve
on FM. Once a station's frequency is stored,
simply press and release the proper
preset button to tune to it.
The preset frequencies will be lost if your car's battery goes dead, is disconnected, or the radio fuse is

removed.

Comfort and Convenience Features
PWR/VOL KNOB

SEEK/SKIP BAR
PRESET BUTTONS

TUNE/MODE KNOBSCAN
BUTTON
AUTO
SELECT BUTTON
AM/FM BUTTON

STEREO INDICATOR

SCAN INDICATOR

Audio System

Preset — You can store the
frequencies of your favorite radio stations in the six preset buttons.
Each button will store one frequency
on the AM band, and two
frequencies on the FM band.
To store a frequency:
1. Select the desired band, AM or FM. FM1 and FM2 let you store
two frequencies with each Preset

button.

2. Use the TUNE or SEEK function to tune the radio to a desired
station.

3. Pick the Preset button you want for that station. Press the button
and hold it until you hear a beep.
4. Repeat steps 1 to 3 to store a total of six stations on AM and twelve
on FM. PWR/VOL
KNOB
FM
BUTTON TUNE KNOB
SEEKBUTTONS
SCAN BUTTON
PRESET BUTTONS

Once a station's frequency is stored,

simply press and release the proper

Preset button to tune to it. The preset frequencies will be lost if
your car's battery goes dead, is disconnected, or the radio fuse is

removed.

Comfort and Convenience Features
CONTINUED

AM

BUTTON
STEREO
INDICATOR

Audio System

Theft Protection
On EX, EX-V6 models

Your car's audio system will disable itself if it is disconnected from
electrical power for any reason. Tomake it work again, the user must
enter a specific five-digit code in the
Preset buttons. Because there are
hundreds of number combinations possible from five digits, making thesystem work without knowing the
exact code is nearly impossible.
You should have received a card that lists your audio system's codenumber and serial number. It is best
to store this card in a safe place at
home. In addition, you should writethe audio system's serial number in
this Owner's Manual. If you should
happen to lose the card, you mustobtain the code number from your
Honda dealer. To do this, you will
need the system's serial number. If your car's battery is disconnected
or goes dead, or the radio fuse is
removed, the audio system willdisable itself. If this happens, you
will see "Code" in the frequency display the next time you turn on the
system. Use the Preset buttons to
enter the five-digit code. If it is
entered correctly, the radio will start
playing.
If you make a mistake entering the
code, do not start over or try tocorrect your mistake. Complete the
five-digit sequence, then enter the correct code. You have ten tries toenter the correct code. If you are
unsuccessful in ten attempts, you must then leave the system on forone hour before trying again. You will have to store your favorite
stations in the Preset buttons after
the system begins working. Your original settings were lost when
power was disconnected.
Comfort and Convenience Features

Battery

On EX and EX-V6 models

If your car's battery is disconnected
or goes dead, the audio system will
disable itself. The next time you turn
on the radio you will see "Code" in
the frequency display. Use the Preset buttons to enter the five-digit
code (see page 174 ).
Charging the battery with the cables
connected can seriously damage your
car's electronic controls. Detach the
battery cables before connecting the
battery to a charger.

Maintenance
The battery gives off explosive
hydrogen gas during normal
operation.
A spark or flame can cause the battery to explode with enough
force to kill or seriously hurt you.
Wear protective clothing and a
face shield, or have a skilled mechanic do the battery
maintenance.
NOTICE

Malfunction Indicator Lamp

Readiness Codes
Your car has certain "readiness codes" that are part of the on-board
diagnostics for the emissions
systems. In some states, part of the
emissions testing is to make sure
these codes are set. If they are not set, the test cannot be completed.
If your car's battery has been
disconnected or gone dead, these
codes are erased. It takes severaldays of driving under various
conditions to set the codes again.
If possible, do not take your car for a
state emissions test until the
readiness codes are set. See State
Emissions Testing on page 336.
(For V6 and L4-ULEV)
To check if they are set, turn the ignition ON (II), but do not start
the engine. The Malfunction
Indicator Lamp will come on for
20 seconds. If it then goes off,
the readiness codes are set. If it blinks 5 times, the readiness
codes are not set. See State
Emissions Testing on pages 301 and
302.
Taking Care of the Unexpected