2001 FORD EXPLORER clock

If the bulb is accidentally touched, it should be cleaned with rubbing
alcohol before being used.
1. With the flat side of the new bulb's plastic base facing upward, insert
the glass end of the bulb into the lamp assembly. You may need to turn
the bulb left or right to align the grooves in the plastic base with the
tabs in the lamp assembly. When the grooves are aligned, push the bulb
into the lamp assembly until the plastic base contacts the rear of the
lamp assembly.
2. Install the bulb retaining ring over the plastic base until it contacts the
rear of the socket by rotating clockwise until you feel a ªstop.º
3. Install the electrical connector into the rear of the plastic base until it
snaps, locking it into position.
4. Turn the headlamps on and make sure they work properly. If the
headlamp was correctly aligned before you changed the bulb, you should
not need to align it again.
Replacing front parking lamp/turn signal/sidemarker bulbs
5. Remove two screws from the
lamp assembly.
6. Disengage lamp assembly.
7. Rotate bulb socket
counterclockwise and remove from
lamp assembly.
8. Carefully pull bulb straight out of
socket and push in the new bulb.
9. Install bulb socket in lamp
assembly by turning clockwise.
10. Align the parking lamp studs
with the plastic grommets on the vehicle and push to snap in place.
11. Install two screws on lamp assembly.
Maintenance and care
245

Replacing tail lamp/turn/backup lamp bulbs
The tail lamp/turn/backup lamp bulbs are located in the tail lamp
assembly, one just below the other. Follow the same steps to replace
either bulb:
1. Open the liftgate to expose the
lamp assemblies.
2. Remove the two screws from the
lamp assembly.
3. Carefully remove the lamp
assembly by pulling it rearward.
4. Rotate the bulb socket
counterclockwise and remove from
lamp assembly.
5. Pull the bulb straight out of the
socket and push in the new bulb.
6. To complete installation, follow the removal procedure in reverse
order.
Replacing foglamp bulbs
1. Remove the bulb socket from the
foglamp by turning
counterclockwise.
2. Disconnect the electrical
connector from the foglamp bulb.
3. Connect the electrical connector to the new foglamp bulb.
4. Install the bulb socket in the foglamp turning clockwise.
Replacing license plate lamp bulbs
1. Remove two screws and the
license plate lamp assembly from
the liftgate.
2. Remove bulb socket from lamp
assembly by turning
counterclockwise.
3. Pull the bulb out from socket and
push in the new bulb.
Maintenance and care
246

4. Install the bulb socket in lamp assembly turning it clockwise,
5. Install the lamp assembly on liftgate with two screws.
Replacing high-mount brake lamp bulbs
1. Remove the two screws and move
the lamp assembly away from the
liftgate.
2. Disconnect the washer hose.
3. Remove the bulb holder from the
lamp assembly by depressing the
snaps.
4. Pull the bulb straight out of the
socket and push in the new bulb.
To complete installation, follow the
removal procedure in reverse order.
Maintenance and care
247

Certification Label ....................262
Child safety restraints ..............145
child safety belts ....................145
Child safety seats ..............145±146
attaching with tether straps ..149
in front seat ............................147
in rear seat ..............................147
Cleaning your vehicle ...............248
engine compartment ..............250
exterior ............................250±251
exterior lamps .........................251
instrument cluster lens ..........253
instrument panel ....................252
interior .............................252±253
mirrors .....................................254
plastic parts ............................251
safety belts ..............................253
washing ....................................249
waxing .....................................249
wheels ......................................251
windows ..................................254
wiper blades ............................252
woodtone trim ........................254
Climate control (see Air
conditioning or Heating) ............23
Clock ..........................42, 48, 58, 71
Compass, electronic ....................94
calibration .................................96
set zone adjustment .................95
Console ......................................105
overhead ....................................92
rear ..........................................106
Controls
power seat ...............................122
steering column ........................90
Coolant
checking and adding ..............216
refill capacities ................219, 255specifications ..................258, 260
Cruise control (see Speed
control) ........................................84
Customer Assistance ................185
Ford accessories for your
vehicle .....................................270
Ford Extended Service Plan....263
Getting assistance outside the
U.S. and Canada .....................269
Getting roadside assistance ...185
Getting the service you need 263
Ordering additional owner's
literature .................................274
The Dispute Settlement
Board .......................................266
Utilizing the
Mediation/Arbitration
Program ...................................269
D
Daytime running lamps (see
Lamps) .........................................22
Defrost
rear window ..............................34
Dipstick
automatic transmission fluid....222
engine oil .................................210
Doors
door ajar warning .....................12
lubricant specifications ..........258
Driveline universal joint and
slip yoke ....................................225
Driving under special
conditions ..........................172, 174
mud ..........................171, 173±174
sand .................................171, 174
snow and ice ...........171±173, 175
through water .........171, 174, 178
Index
277