2001 FIAT SEICENTO light

4
English
2. HANDLING COMPACT DISCS
This unit has been designed specifically for
playback of compact discs bearing the
mark. No other discs can be played.
To remove the compact disc from its storage
case, press down on the centre of the case
and lift the disc out, holding it carefully by the
edges.
Always handle the compact disc by the
edges. Never touch the surface.
To remove fingermarks and dust, use a soft
cloth, and wipe in a straight line from the cen-
tre of the compact disc to the circumference.
Note on Compact DiscNever stick labels on the surface of the com-
pact disc or mark the surface with a pencil or
pen.
New discs may have some roughness around
the edges. The unit may not work or the
sound may skip if such discs are used. Use a
ball-point pen, etc. to remove roughness from
the edge of the disc.Do not use any solvents such as commercial-
ly available cleaners, anti-static spray, or thin-
ner to clean compact discs.
Do not use compact discs that have large
scratches, are misshapen, or cracked, etc.
Use of such discs will cause misoperation or
damage.
Do not expose compact discs to direct sun-
light or any heat source.
Note:
.• Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These may
get caught in the internal mechanism and damage the disc.
Be sure to unfold and read the next page. / Veuillez déplier et vous référer à la page suivante.
Bitte ausbreiten und die nächste Seite lesen. / Assicurarsi di aprire e leggere la pagina successiva.
Volgende pagina uitvouwen en doorlezen a.u.b. / Cerciórese de desplegar y de leer la página siguiente.
Glöm inte att vika ut och läsa nästa sida. / Não deixe de abrir e ler a próxima página.
˙
PU2312 003-006 GB 14-01-2008 14:57 Pagina 4 Proper way to hold
the compact discRemoving the disc No Ball-point pen
Roughness No No No No

7
English
5. NOMENCLATURE
Note: Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page
5 (unfold).
Names of Buttons
1DCP Release button
2A-M (audio mode) button
LD (loudness) button
3POWER button
FNC (function) button
4CD insertion slot
5Eject (Q) button
6DISP (display) button
7TA (traffic announcement) button
8PTY (programme type) button
RDM (random) button
9AF (alternative frequencies) button
RPT (repeat) button
Display Items
1Volume indication (VOL)
2Audio mode indication (A-M)
3Rear speaker indication (R)
Front speaker indication (F)
4Operation status indication
*The frequency, PTY, play time, clock (CT),
etc. are displayed.
5Loudness indication (LD)
6Z-enhancer indication (Z-EHCR)
7CD/MD
CHANGERmode indication
8Magazine number indication
9Disc indication (DISC)
0Random indication (RDM)
!Repeat indication (RPT)0PS/AS (preset scan/auto store) button
SCN (scan) button
!Preset buttons (1 to 6)
Direct buttons (1 to 6)
@Z-EHCR (z-enhancer) button
#BND (band) button
TOP button
MAG (magazine) button
$SRCH (search) buttons (Left aand Right
d)
%Rotary knob
¥Play/pause (s) button
MUTE button
@Scan indication (SCN)
#Preset channel indication (1 to 6)
Disc number indication (1 to 6)
*The disc numbers corresponding to the
discs in the CD/MD changer light.
$Programme type indication (PTY)
%Traffic programme indication (TP)
¥Traffic announcement indication (TA)
&Regional indication (REG)
*Alternative frequency indication (AF)
(Manual indication (MANU)
)Left speaker indication (L)
Right speaker indication (R)

Be sure to set the volume to the minimum level
before turning off the power to the unit.
Loud sounds when turning on the power may
impair your hearings or cause damage to the
unit.
Turning on/off the power
Note:
•Do not use the sound system for a long time when
the engine is off. You may have problems in start-
ing the engine or shorten the life of the battery.
1. Press POWER button 3.
2. The illumination and display on the unit light up.
The unit automatically remembers its last oper-
ation mode and will automatically switch to dis-
play that mode.
3. Press and hold POWER button 3for 1 second
or longer to turn off the power for the unit.
Selecting a mode
1. Press FNC button 3to select a function mode.
2. The function mode changes in the following
order:
Radio ➜CD ➜CD/MD
CHANGER➜Radio …
*If the CD/MD CHANGERis not connected, the CD/
MD CHANGERmode cannot be selected.
Adjusting the volume
Turning the rotary knob %clockwise increases
the volume; turning it counterclockwise decreases
the volume.
*The volume level is from 0 (minimum) to 33
(maximum).
Setting the Z-enhancer
This unit comes with 3 types of sound tone effects
stored in memory. Select the one you prefer.
*The factory default setting is “OFF”.
Each time you press Z-EHCR button @, the tone
effect changes in the following order:
“Z-ENHANCER 1” ➜“Z-ENHANCER 2” ➜
“Z-ENHANCER 3” ➜“OFF” ➜“Z-ENHANCER 1”...
•Z-ENHANCER 1 : bass emphasized
•Z-ENHANCER 2 : treble emphasized
•Z-ENHANCER 3 : bass and treble emphasized
•OFF : no sound effect
Adjusting the tone
Press A-M button 2and select the item to adjust.
Each time you press A-M button 2, the item
changes in the following order:
“BASS” ➜“TREB” ➜“BAL” ➜“FAD” ➜
Function mode...
Adjusting the bass
1. Press A-M button2and select “BASS”.
2. Turning the Rotary knob %clockwise empha-
sizes the bass; turning it counterclockwise
attenuates the bass.
*The factory default setting is “0”.
(Adjustment range: –6 to +6)
3. When the adjustment is complete, press A-M
button 2several times until the function mode
is reached.
Adjusting the treble
1. Press A-M button 2and select“TREB”.
2. Turning the rotary knob%clockwise empha-
sizes the treble; turning it counterclockwise
attenuates the treble.
*The factory default setting is “0”
(Adjustment range: –6 to +6)
3. When the adjustment is complete, press A-M
button 2several times until the function mode
is reached.
8
Note: Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page
5 (unfold).
Basic OperationEnglish
6. OPERATION
éCAUTION

●Turning AF function off
When “AF”is lit or flashing in the display, press
AF button 9. “AF”in the display goes off and AF
turns off.
●Turning AF function on
When “AF”is not lit in the display, press AF but-
ton 9again. “AF”lights in the display and AF
turns on.
If the receiving condition of a station being tuned
is getting worse, “AF”starts flashing and the unit
tries to switch to an alternative frequency. If
switching cannot be performed, the display
switches to “SEARCH”and the unit searches for
the same programme.
REG (Regional Programme) function
When REG function is on, regional station recep-
tion is optimized.
If this function is off, the unit switches in to the
regional station in the next local area when you
enter the next area while receiving the regional
station in the previous local area.
*The factory setting is “off”.
Notes:
• This function is ineffective when a national station
such as BBC 2 FM is being received.
• The on/off setting of REG is effective when AF is
on.
●Turning REG function on
When “REG”is not lit in the display, pressing and
holding AF button 9for 2 seconds or longer.
“REG”lights in the display.
●Turning REG function off
Pressing and holding AF button 9for 2 seconds
or longer again,“REG”in the display goes off.
12
RDS Operations
English
RDS mode
RDS (Radio Data System)
This unit incorporates an RDS system decoder for
use with stations broadcasting RDS data.
This system enables the radio to display the
name of the station being received (PS), and also
to automatically switch to a better frequency when
one is available while you are traveling great dis-
tances (AF switching).
It can also interrupt a CD or tape with traffic infor-
mation or the programme type broadcast by an
RDS station.
Additionally, if EON information is received, this
information enables automatic switching of other
preset stations on the same network and interrup-
tion of the station being received with traffic infor-
mation from other stations (TP). This function may
not work in some regions.
To use the RDS function, be sure to set the radio
to FM mode.
•AF:Alternative Frequencies
•PS:Programme Service Name
•PTY:Programme Type
• EON:Enhanced Other Network
•TP:Traffic Programme
*If an RDS station can no longer be received
clearly (at the current location), “AF”flashes in
the display. When reception is restored, “AF”
stops flashing.
AF function
The AF function enables the unit to maintain opti-
mum reception by switching to different frequen-
cies on the same network.
*The factory setting is“on”.
Seek tuning indication
AF indication
PTY indication
TP indication REG indication
TA indicationPreset channel indication

Manual tuning of related regional
stations
1. This function works when AF is on and REG is
off.
Note:
•This function is effective when related regional
stations are received.
2. Press one of Preset buttons !to recall a
regional station.
3. If the receiving condition of a recalled station is
bad, press the same Preset button !. The unit
switches to a related regional station.
TA (Traffic Announcement)
When the unit is in the TA standby mode, you can
listen to traffic announcements preferentially
when they start, irrespective of the function mode.
You can also tune in to TP (traffic programme)
stations automatically.
●To set the TA standby mode
If you press TA button 7when only “TP”is lit in
the display, “TP”and “TA”light in the display and
the unit is set to the TA standby mode until traffic
announcements start.
When traffic announcements start, “TRA INFO”
appears in the display, and then PS (Programme
Service Name) appears.
If you press TA button 7while traffic announce-
ments are being broadcast, they are cancelled
and the unit enters TA standby mode.
●Cancelling the TA standby mode
If you press TA button 7when“TP”and
“TA””are lit in the display, “TA”in the display
goes off and the TA standby mode is cancelled.●Setting the auto tuning mode for TP stations
If you press TA button 7when only “TP”is lit or
“TP”and “TA”are not lit in the display,“TA”lights
and the unit automatically tunes in to TP stations.
Note:
•The unit continues to tune in automatically if no TP
station is received. Press TA button 7again to
stop auto tuning.
Auto store function for TP stations
● Auto storing while “TA” is lit:
Only TP stations are auto stored.
*Refer to PS/AS function in radio mode.
PTY function
This function enables you to listen to selected pro-
gramme type, irrespective of the function mode.
•PTY broadcasts are not yet available in all coun-
tries.
In TA standby mode, TP stations have priority
over PTY broadcasting stations.
*Emergency messages interrupt all modes of oper-
ation. They can only be received from RDS sta-
tions. “ALARM”appears in the display and mes-
sage can be heard.
*Press AF button 9to cancel the ALARM broad-
casts.
13
RDS Operations
English

Selecting PTY
1. When you press PTY button 8,“PTY”lights
and PTY appears in the display. The unit enters
PTY select mode.
If the control is idle for 7 seconds after the PTY
select mode has been entered, the display
automatically returns to radio mode display and
the unit enters the PTY standby mode.
2. Select a PTY.
Press one of Preset buttons !to select the
desired PTY or select up or down to obtain a
desired PTY using Rotary knob %.
*The following stored already into the Preset
buttons !for your convenience.
Preset memory of PTYs
1. Press PTY button 8to enter PTY select mode.
If the control is idle for 7 seconds after the PTY
select mode has been entered, the display
automatically returns to radio mode display and
the unit enters the PTY standby mode.
2. Select up or down to obtain a desired PTY
using Rotary knob %.
The following 15 PTYs are selectable.
14
RDS Operations
English
PresetNo.
1
2
3
4
5
6
PTY
ENGLISH
NEWS
INFO
CLASSICS
SPORT
POP M
M, O, R, M(English)
(News)
(Information)
(Classic music)
(Sports)
(Popular music)
Middle of the Road Music
PTY Display
ENGLISH
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
M, O, R, M
LIGHT M
CLASSICS
OTHER M
(English)
(News)
(Affairs)
(Information)
(Sports)
(Education)
(Drama)
(Culture)
(Science)
(Variety)
(Popular music)
(Rock music)
Middle of the Road Music
(Light music)
(Classic music)
(Other music)
3. Press PTY button 8again to enter standby
mode for the selected PTY.
When a selected PTY broadcast starts, the
selected PTY appears in the display.
If you press PTY button 8 during PTY broad-
casts, PTY broadcasts are temporarily can-
celled and the unit enters PTY standby mode.
●Cancelling PTY standby mode
Press and hold PTY button 8for 2 seconds or
longer to turn off“PTY”in the display.3. Press and hold one of the Preset buttons!
1 to 6 for 2 seconds or longer to put it into
memory. After PTY is stored in memory, “PTY
MEMO”appears in the display.

Selecting a track
●Next track:
Select the SRCH Right button $.
●Current track:
Select the SRCH Left button $.
●Previous track:
Select the SRCH Left button $, do the same
again.
*Each time you select left or right using SRCH but-
tons $, the track is skipped accordingly.
Fast-forward/fast-backward (FF/FB)
●Fast-forward:
Press right and hold for 1 second or longer using
button $.
●Fast-backward:
Press left and hold for 1 second or longer using
button $.
*Press left or right buttons $for 3 seconds or
longer to increase the speed.
Top function
The top function allows the first track of the cur-
rent CD to be played.
Press TOP button #to play the first track (track
No. 1) of CD.
Scan play
The scan play allows the first 10 seconds of all the
tracks on the CD to be played.
* The scan play is useful when you want to select a
desired track.
1. Press SCN button 0. “SCN”lights in the dis-
play.
2. To cancel the scan play, press SCN button 0
again. “SCN”goes off from the display and the
normal play resumes.
Repeat play
The repeat play allows the selected track to be
played repeatedly.
1. Press RPT button 9. “RPT”lights in the dis-
play.
2. To cancel the repeat play, press RPT button 9
again. “RPT”goes off from the display and the
normal play resumes.
Random play
The random play allows all the tracks on the cur-
rent CD to be played randomly.
1. Press RDM button 8. “RDM”lights in the dis-
play.
2. To cancel the random play, press RDM button
8again. “RDM”goes off from the display and
the normal play resumes.
17
CD Operations
English

CD CHANGERmode (where fitted)
Listening to a CD in the CD
CHANGER
When a separately sold CDCHANGERis connect-
ed to the sound system, you can listen to CD.
1. Press FNC button 3and select CD
CHANGERmode to start play.
*The CD No. of magazine where CDs are loaded
light in the display.
2. When a magazine is not set in the CD CHANG-ER, “NO MAGA”appears in the display.
*If a magazine is set while “NO MAGA”is being
displayed,“LOADING”appears in the display
for a moment, “PAUS”appears in the display,
and the operation pauses.
3. When a CD is not set in the magazine, “NO
DISC”appears in the display.
*Insert a CD into the magazine and set the mag-
azine in the CD CHANGER.
CD-ROMs cannot be played with CD CHANGER.
Note:
•When a CD CHANGERis connected, be sure to turn
off the main unit and turn it again.
Pausing play
1. Press Play/pause button ¥to pause play.
“PAUS”appears in the display.
2. To resume play, press Play/pause button ¥
again.
Selecting a CD
Each of the Direct buttons !corresponds to a
disc loaded into the magazine.
●Selecting a disc from 1 to 6
Press the corresponding Direct button !(1 to 6)
to select the desired disc.
●Selecting a magazine from 1 to 3
(only when there is disc in the magazine)
Press BND button #to select the desired maga-
zine.
*If a CD is not loaded in a slot of the magazine,
pressing the Direct button !corresponding to its
disc number is invalid.
Selecting a track
●Next track:
Select the SRCH Right button $.
●Current track:
Select the SRCH Left button $.
●Previous track:
Select the SRCH Left button $, do the same
again.
*Each time you select the SRCH Left/Right button
$, the track is skipped accordingly.
18
CD CHANGEROperations
English
CD CHANGERmode indication
Random indicationDisc indication Magazine number
indication
éCAUTION
Disc number indication
Scan indication
Repeat indication