2001 FIAT MAREA fıat marea

Marea- Marea Weekend
2000 range ©
Technical Data
Wheels
WHEEL ALIGNMENT
00.44
unladen vehicle (•)
camber (**)
caster (**)
front
suspension
toe-in
offset
front wheels
±3*
36' 24» ± 30'
10 57' ± 30'
-1 - 1 mm
camber (**)
U1
rear
suspension
toe-in (**)
thrust angle
rear wheels i
-0° 45' ± 30'
2 ± 2 mm
(**) Angles not adjustable
(•) With the tyres inflated to the correct pressure and the vehicle in running order with 5 litres of fuel (•) Angular values, which cannot be adjusted, used for the correct alignment of the vehicle
Copyright by Fiat Auto 41

Technical Data
Front suspension
00.44
ENGINE TYPE h|p>jrD
Dampers
Make Double acting, telescopic, hydraulic
Open (start of buffering) mm 508 ± 2.5 501 ± 2.5
Closed (iron against iron) mm 361 ± 2.5 354 ± 2.5
Stroke mm 147
Anti-roll bar
Anti-roll bar diameter mm 18
Marea- Marea Weekend
2000 range ©
Copyright by Fiat Auto 43

Marea Weekend Technical Data
2000 range o Rear suspension
00.44
Rear suspension independent with track control arms anchored to an auxiliary crossmember. Variable
flexibility coil springs and anti-roll bar. Gas shock absorbers with low friction coefficient lower bushes.
ENGINE TYPE
Coil springs
Wire diameter mm 12.3±0.1 12.8±0.1
Number of effective coils 5.93 5.93
Coil direction clockwise
Released spring height mm 320 322
419-445 daN mm
Spring height under
184 -
a load of:
432 daN mm -184
Spring are divided into two categories,
identified by markings
412 daN
yellow (1) for those: oT mm
>184 _
under a load of hpinht
432 daN a
of mm
->184
412 daN aJS* green (1) for those ot mm
<184 -
under a load of: _ hpiflht 432 daN a "eif£J ot mm -<184
(1) Springs of the same type must be fitted.
Dampers
Make double acting, telesopic, gas
Open (start of damping action) mm 321 ± 2
Closed (iron against iron) mm 224 ± 2
Stroke mm 97
Anti-roll bar
Anti-roll bar diameter mm 17
Copyright by Fiat A uto 45

Marea- Marea Weekend Technical Data
2000 range (§) Electrical equipment: starting
00.55
STARTER MOTOR l^p| 20v I^P) JTD
Make Bosch
DW -12V -1,1 kW
Bosch
0 74.5-1.1/12
Bosch
0 78.5-2 KW/12
Voltage V 12
Nominal power kW 1.1 1.1 2
Rotation, pinion side clockwise
No. of poles 6 4 6
Winding windings in series permanent magnets
Engagement free wheel
Operation solenoid
End float of armature shaft mm 0.1-0.5 0.1-0.5 0.1-0.5
Data for bench test
Operating test (*):
current A
speed rpm
voltage V
torque developed daNm
-
360-380
1150
8.15
1.30
500
1950
7.30
1.30
Engagement test (*):
current A
voltage V
torque developed daNm
-680-700
4.9
3.11
1200
5.5
3.0
Idle test (*):
current A
voltage V
speed rpm
-
60-80
4.9
4040
70-80
11.5
5450-5750
Relay [ pull in Q -0.33-0.37 0.4
Winding
resistance (*) 1 hold in Q -1.13-1.27 1.7
Lubrication
Internal splines and
shaft bushes
VS+ SAE 10W
Enagement sleeve and intermediate
disc TUTELA MR3
(*) Data obtained at an ambient temperature of 20°C.
NOTE When overhauling it is not necessary to undercut the insulator between the commutator bars
Copyright by Fiat Auto 47

Technical Data
Electrical equipment: recharging
00.55
Bosch KCB1-14V-45/80A
Bosch KCB2-14V-50/90A
M. Marelli A127IR-14V-55/100A
M. Marelli A115IM-14V-55/105A
M. Marelli RTM 151 B
Marea- Marea Weekend
2000 range ©)
Alternator wiring diagram
Typical voltage regulator curves
M. Marelli RTM 151 A
Copyright by Fiat Auto 49

Marea- Marea Weekend Technical Data
2000 range © Electrical equipment: electronic injection- ignition
00.55
INTEGRATED ELECTRONIC
INJECTION/IGNITION SYSTEM I^P) 20v
Make Bosch ME31F001
Firing order 1-2-4-5-3
IGNITION COIL (1 PER SPARK PLUG)
Make Bosch
Type 0.221.504.014
Ohmic resistance of primary winding at 20°C Q 0.,4
Ohmic resistance of secondary winding at 20°C Q 8500
TOP DEAD CENTRE AND RPM SENSOR
Make and type Bosch 0.281.002.102
Sensor winding resistance at 20°C Q 774 + 946
Distance (gap) between sensor and
crankshaft pulley tooth 0.8 H- 1.5
DETONATION SENSOR
Make Bosch
Type 0.261.231.095
SPARK PLUGS
Make and type CHAMPION RC8BYC
Thread on engine M 14x 1.25
Spark gap mm 0.8
Copyright by Fiat Auto 51

Marengo^™ Introduction and technical data
2000 range Index
oo.
page
INTRODUCTION
- Identification data 1
- Dimensions 1
- Weights 2
- Performance 2
- Fuel consumption 2
TECHNICAL DATA
- Front suspension 3
- Rear suspension 3
NOTE
This section gives technical data for the Fiat Marengo 2000 range equipped with a 1910 JTD EC F3 en­
gine. For further information, see the Fiat Marea - Fiat Marea Weekend manual publication no. 506.763
and subsequent updates
Copyright by Fiat Auto

Marea Weekend 9 ™*» Introduction - Technical Data
2000 range Index
00.
page
INTRODUCTION
- Identification data 1
- Performance - Fuel consumption 1
- Fuel consumption 2
TECHNICAL DATA
ENGINE
- Specifications 2
Copyright by Fiat Auto