2001 CADILLAC DEVILLE light

2-58
This is the on/off button, located on the lower left
side of the mirror for the electrochromic and compass
functions of the rearview mirror.
The mirror also includes an eight
-point compass
display in the upper right corner of the mirror face.
When on, the compass automatically calibrates as the
vehicle is driven.
When cleaning the mirror, use a paper towel or similar
material dampened with glass cleaner. Do not spray
glass cleaner directly on the mirror as that may cause the
liquid cleaner to enter the mirror housing.
Mirror Operation
To turn on the automatic dimming feature, press
and hold the on/off button for about three seconds.
To turn off automatic dimming, press and hold the
on/off button for about three seconds again. The green
indicator light will be illuminated when this feature is
active. The automatic dimming feature will be active
each time the vehicle is started.Compass Operation
Press the on/off button once to turn the compass on
or off.
When the ignition and the compass feature are on,
the compass will show two character boxes for
approximately two seconds. After two seconds,
the mirror will display the compass heading.
Compass Calibration
If after two seconds, the display does not show a
compass heading (ªNº for North, for example),
there may be a strong magnetic field interfering with
the compass. Such interference may be caused by a
magnetic antenna mount, magnetic note pad holder or
a similar magnetic item. If the letter ªCº should ever
appear in the compass window, the compass may
need calibration.
The mirror can be calibrated by driving the vehicle in
circles at 5 mph (8 km/h) or less until the display reads
a direction.
The compass can be placed in calibration mode by
pressing and holding the on/off button until a ªCº is
shown in the compass display.

2-63
When not being used, the center seat lap belt can be
stored in the underseat storage compartment as shown.
Convenience Net
The convenience net is located inside the back wall of
the trunk. Put small loads, like grocery bags, behind the
net. It can help keep them from falling over during sharp
turns or quick starts and stops.
The net is not for larger, heavier loads. Store them in the
trunk as far forward as you can. When not using the net,
hook the net to the tabs securing it to the sill plate.
Ashtrays and Cigarette Lighter
NOTICE:
Don't put papers or other flammable items
into your ashtrays. Hot cigarettes or other
smoking materials could ignite them, causing a
damaging fire.
Front Ashtray
With the full floor console, the ashtray is located below
the climate control system. To open, push down on
the cover. To clean the ashtray, lift it out by gripping
the sides.
For vehicles without the floor console, pull the tray
located below the radio to reveal the ashtray. The
ashtray can be removed for cleaning.
Rear Ashtray
To use the side rear ashtray located on the armrest,
lift the lid.

2-64
Cigarette Lighter
The cigarette lighter is located near the ashtray. Press it
all the way in and release. It will pop back out by itself
when it's ready to light. You may also have a lighter
located at the rear seat air outlet.
Cigarette lighters can be used to provide electrical
power to accessories. See ªAccessory Power Outletsº in
the Index.
NOTICE:
Don't hold a cigarette lighter in with your hand
while it is heating. If you do, it won't be able to
back away from the heating element when it's
ready. That can make it overheat, damaging the
lighter and the heating element.
Sun Visors
Swing down the primary visor to block out glare. It can
also be detached from the center mount and moved to
the side while the auxiliary sunshade remains to block
the glare from the front. The visors also have
side
-to-side slide capability.
The driver's sunshade is also equipped with a
storage flap.
Lighted Visor Vanity Mirror
Pull the visor down and lift the cover. Move the slide
switch up or down to brighten or dim the lamp.
Lighted Rear Vanity Mirror (If Equipped)
Pull the vanity cover down to see the mirror. Move the
slide switch up or down to brighten or dim the lamps.
Coat Hooks
Your vehicle is equipped with flip-out coat hooks.
They are located above the rear doors, behind the rear
assist handles. Return them to the stowed position when
not in use.

2-65
Rear Power Sunshade (If Equipped)
The rear power sunshade helps to reduce the amount of
heat and light entering the rear window.
The rear power sunshade is located in the rear shelf. To
raise the power sunshade, press and release the REAR
SHADE switch located on the front overhead console.To close the power sunshade, press and release the
REAR SHADE switch again. The rear power sunshade
switch only works when the ignition is on or when the
Retained Accessory Power is active. See ªRetained
Accessory Powerº in the Index.
Never store objects on the rear shelf because they
may get caught in the sunshade or be tossed about in
your vehicle.
Manual Rear Side Door Sunshade
(If Equipped)
To use the manual rear side door sunshades, lower the
side windows and hook the top edge of the retractable
sunshades over the edge of the windows and raise the
windows. To remove the shades, lower the windows and
the hooks will disengage automatically.

2-68
Volume Control: You can control the volume of the
OnStar System using the steering wheel volume control.
Telltale Light: This light will indicate the status of
the system. A solid green light will come on when you
start the vehicle to let you know that the system is on
and is ready to make or receive calls.
If the light blinks green it means that an incoming
or outgoing call is in progress. Press the
Call ANSWER/END button if you notice the
light blinking and you are not on a call.
The light will be red in the event of an OnStar system
malfunction. If this occurs press the OnStar button to
attempt to contact an advisor. If the connection is made,
the advisor will assist you with steps to take to make
sure that the system is functioning properly. If you
cannot contact the advisor, take your vehicle to your
dealership as soon as possible for assistance.
Safety and Security Services

Automatic Notification of Air Bag
Deployment
-- If an air bag deploys, a priority
emergency signal is automatically sent to the
center. An advisor will locate your vehicle's
position, try to contact you and assist you in the
situation. If the center is unable to contact you,
an emergency service provider will be contacted.

Stolen Vehicle Tracking
-- Call the center at
1
-888-4-ONSTAR (1-888-466-7827) to report
your vehicle stolen. The system can then locate
and track your vehicle and the advisor will be
able to notify the proper authorities.

Roadside Assistance with Location
-- For
vehicle breakdowns, press the OnStar button.
An advisor will contact the appropriate help.

Remote Diagnostics
-- If an instrument panel
light comes on, the center can perform a check of
the engine on
-board computer. An advisor can
then recommend what action needs to be taken.

2-71
Sunroof (Option)
The two control switches to operate the sunroof are
located on the overhead console and include VENT,
ROOF, open and close.
The control switches work only when the ignition is
on or the Retained Accessory Power (RAP) is active.
See ªRetained Accessory Powerº in the Index.To open the glass panel and sunshade, press and
hold the ROOF switch rearward to the first position.
The sunshade can also be opened by hand. To close the
glass panel, press and hold the ROOF switch forward.
As the glass panel closes, it will open slightly toward the
vent to provide a better seal. The sunshade can only be
closed by hand.
To express
-open the glass panel to a partially open
position, press and release the ROOF switch rearward
to the second position. The glass panel may be fully
opened by pressing the ROOF switch again.
To stop the glass panel when express opening, press
either the ROOF or VENT switch in any direction.
If you press and hold the ROOF switch in the express
open position for more than one second, the express
open operation will be over
-ridden and the sunroof will
stop when the switch is released.
To vent the glass panel, press and hold the VENT switch
in the open position. The sunshade must be opened by
hand. To close the glass panel, press and hold the VENT
switch in the close position.

2-73
Your vehicle's engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. If you have previously programmed a transmitter
channel, proceed to Step 2. Otherwise, hold down
the two outside buttons on the HomeLink
Transmitter until the indicator light begins to flash
rapidly (after 20 seconds). Then release the buttons.
This procedure initializes the memory and erases any
previous settings for all three channels.
2. Decide which one of the three channels you want to
program. Hold the end of the hand
-held transmitter
about 2 to 5 inches (5 to 13) away from the surface
of the HomeLink Transmitter so that you can still see
the indicator light.
3. Using both hands, press the hand
-held transmitter
button and the desired button on the HomeLink
Transmitter. Continue to press both buttons
through Step 4.
4. Hold down both buttons until you see the indicator
light on the HomeLink Transmitter flash slowly and
then rapidly. The rapid flashing indicates that the
HomeLink Transmitter has been programmed.
Release both buttons once the indicator light starts
to flash rapidly.If you have trouble programming the HomeLink
Transmitter, make sure that you have followed the
directions exactly as described. The HomeLink
Transmitter may not work with older garage door
openers that do not meet current Federal Consumer
Safety Standards. If you cannot program the
transmitter after repeated attempts, refer to ªRolling
Code Programmingº later in this section or
contact the HomeLink Transmitter manufacturer
at 1
-800-355-3515.
Be sure to keep the original hand
-held transmitter
in case you need to erase and reprogram the
HomeLink Transmitter.
Canadian Programming: During programming,
the hand
-held transmitter may automatically stop
transmitting after one or two seconds. In this case, you
should press and re
-press the button on the hand-held
transmitter every two seconds without ever releasing the
button on the HomeLink Transmitter. Release both
buttons when the indicator light on the HomeLink
Transmitter begins to flash rapidly.

2-74
Operating the HomeLink Transmitter
Press and release the appropriate button on the
HomeLink Transmitter. The indicator light comes on
while the signal is being transmitted.
The HomeLink Transmitter is disabled when the
VALET lockout switch inside the glove box is activated.
For more information, see ªValet Lockout Switchº in
the Index.
If the hand
-held transmitter appears to program the
HomeLink Transmitter but does not open your garage
door, and if the garage door opener was manufactured
after 1996, the garage door opener may have a ªrolling
codeº system. A rolling code system changes the code
of the garage door opener every time you open or close
the garage door.
To determine if you have this system, press the button
on the HomeLink Transmitter that you have
programmed already. If the indicator light on the
HomeLink Transmitter flashes rapidly for two seconds
and then turns solid, the garage door opener has a
rolling code system. In a rolling code system, the
garage door motor head unit must be trained to the
HomeLink Transmitter.
ªRolling Codeº Programming (If Equipped)
If you have not previously programmed the hand-held
transmitter to the HomeLink Transmitter, see
ªProgramming the HomeLink Transmitterº listed
previously. If you have completed this programming
already, you now need to train the garage door opener
motor head unit to recognize the HomeLink Transmitter.
Refer to your garage door opener owner's manual for
the proper transmitter training procedure for your garage
door opener brand.
1. Find the training button on the garage door opener
motor head unit. The exact location and color of the
button may vary by garage door opener brand. If you
have difficulty finding the training button, refer to
your garage door opener owner's manual.
Because of the steps involved, it may be helpful to
have another person available to assist in programming
the transmitter.
2. Press the training button on the garage door opener
motor head unit.
Following this step, you have 30 seconds to start Step 3.