2001 BMW 5 SERIES phone

EN/13Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
8. To prepare the installation site for the microphone in cars with a sunroof
0Take the existing front headlining trim off the
headlining and remove the switch (20) for the glass
tilt/slide sunroof.
Discard the existing front headlining trim and
replace it with the new front headlining trim (9).
Secure the microphone trim (10) and the switch
(20) for the glass tilt/slide sunroof in the new front
headlining trim (9).
Then fit the new front headlining trim (9) back into
the headlining.
10
920
F 39 0969 B

EN/16Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
9. To install the basic wiring harness A (E39 cars only)
0Cars without an on-board monitor radio only
This step only applies to cars without an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin plug
casing X18126.
"
Connect branch A14, socket contact, white/green
cable, to the free slot in the radio connection plug
(20) PIN11 on the 8-pin plug casing X18126.
0
This step only applies to cars with an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin plug
casing X18126.
"
Cut off the basic wiring harness A near branch
A14.
Connect branch A14, white/green cable, to the
supply cable of the radio connection plug (20)
PIN11, white/green cable, on the 8-pin plug
casing X18126 using a 2-way insulation-piercing
connector (1).
0Applies to all E39 cars
The figure shows the area with the removed
driver’s seat.
"
Pull up the driver's side carpet at the rear (20) and
lay the basic wiring harness A as shown in the
figure and secure it with textile adhesive tape (21).
Lay branch A5, black 3-pin socket casing, along
the left door sill towards the front.
0Thread branch A5, black 3-pin socket casing on
the basic wiring harness A near the left A pillar
through the instrument panel from below and
along the left A pillar upwards to the headlining
and secure it with textile adhesive tape.
As you lay branch A5 to the microphone
installation site, ensure that the cable is
properly routed in the cable duct to prevent
any impairment of the head airbag
function.
"
See instructions for head airbag."
20
039 0001 B
A14
X18126/PIN11
20
20
039 0002 B
A14
211
A
20 X18126
21
21
A
A520
F 39 0977 B
F 39 0981 BIIIIIIIIIIIIIIIIIIIIIIIIIIIII
A5
A
!
!

EN/17Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
9. To install the basic wiring harness A (E39 cars only)
0
The figure shows the boot on the left."
Thread the basic wiring harness A with branches
A6 to A13 and A15, as shown in the figure, through
the passage grommet (20) along the standard
wiring harness to the boot and secure it with cable
ties (3).
0Disconnect the white 12-pin plug connector X322.
Insert branch A12, white 12-pin plug casing, and
branch A13, white 12-pin socket casing on the
basic wiring harness between the above
connectors.
Secure the new plug connectors A13+X322S and
A12+X322B, as shown in the figure.
0Lay branch A6, black 3-pin socket casing, and
branch A7, coaxial socket casing FME, to the
installation site of the compensator/telephone
aerial and connect them if necessary.
Screw the FME connector (4) to branch A7
(required if you are installing the bumper aerial).
Tie back any excess cable lengths.
"
0Cars without an on-board monitor radio only
Insulate branch A9, black 12-pin plug casing,
branch A10, socket contact, white/brown cable,
and branch A15, socket contact, white/green
cable, on the basic wiring harness A and tie them
back on the standard wiring harness.
Branches A9, A10 and A15 are no longer
required.
"
20
A
3
A11
A6
A13
A12A8
A7
A9A10
A15
F 39 0978 B
A12 X322S
A13
X322B
A
F 39 0979 B
A6
4A7
F 39 0980 B
A
A9 A10
A15
F 39 0982 B

EN/23Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0Cars without an on-board monitor radio only
This step only applies to cars without an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin plug
casing X18126.
"
Connect branch A14, socket contact, white/green
cable, to the free slot in the radio connection plug
(20) PIN11 on the 8-pin plug casing X18126.
0
This step only applies to cars with an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin plug
casing X18126.3
Cut off the basic wiring harness A near branch
A14.
Connect branch A14, white/green cable, to the
supply cable of the radio connection plug (20)
PIN11, white/green cable, on the 8-pin plug
casing X18126 using a 2-way insulation-piercing
connector (1).
0Applies to all E39/2 cars
The figure shows the area with the removed
driver’s seat.
"
Pull up the driver's side carpet at the rear (20) and
lay the basic wiring harness A as shown in the
figure and secure it with textile adhesive tape (21).
Lay branch A5, black 3-pin socket casing, along
the left door sill towards the front.
0Thread branch A5, black 3-pin socket casing on
the basic wiring harness A near the left A pillar
through the instrument panel from below and
along the left A pillar upwards to the headlining
and secure it with textile adhesive tape.
As you lay branch A5 to the microphone
installation site, ensure that the cable is
properly routed in the cable duct to prevent
any impairment of the head airbag
function.
"
See instructions for head airbag."
20
039 0001 B
A14
X18126/PIN11
20
20
039 0002 B
A14
211
A
20 X18126
21
21
A
A520
F 39 0977 B
F 39 0981 BIIIIIIIIIIIIIIIIIIIIIIIIIIIII
A5
A
!
!

EN/24Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0
The figure shows the boot on the left."
Lay the basic wiring harness A, as shown in the
figure, with branches A6 to A13 and A15 along the
standard wiring harness and secure it with cable
ties (3).
0Lay branch A6, black 3-pin socket casing, and
branch A7, coaxial socket casing FME, to the
installation site of the compensator/telephone
aerial and connect them.
Screw the FME connector (4) to branch A7
(required if you are installing the bumper aerial).
Tie back any excess cable lengths.
"
0Connect branch A12, white 12-pin plug casing
on the basic wiring harness A to branch B1, white
12-pin socket casing on the power supply wiring
harness B.
Tie back plug connector A12 + B1 on the standard
wiring harness.
0Insulate branch A13, white 12-pin socket casing
and tie it back on the standard wiring harness (no
longer required).
F 39 0997 B
A7A63A12
A13A11
A10
A9
A8
A15
4
A6 A7
F 39 0998 B
A12A
B1B
F 39 0999 B
A13
F 39 1000 B

EN/31Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
12. Circuit diagram for the basic wiring harness A in E39 cars
Legend
F1*Floating fuse holder near the left tail light
X001*Socket contact
X002*Black 18-pin plug casing
X003*Socket contact
A1*Console aerial connector
A4*Black 18-pin socket casing
A5*Black 3-pin socket casing; cable compensator
A7*Boot aerial connector
A12*White 12-pin plug casing
A13*White 12-pin socket casing
N9Radio
X13016Cable eyelet, 6 mm in diameter; earth
X13598Black 12-pin plug casing
X181268-pin plug casing
X18507Black 3-pin connection plug; microphone
1)To standard wiring harness
2)To hands-free system wiring harness
The components and X designations marked with an asterisk (*) are only valid for this circuit
diagram.
All the other components and X designations correspond to BMW after-sales circuit diagrams
Colour abbreviations
BL = Blue OR = Orange
BR = Brown OR = Orange
GE = Yellow SW = Black
GN = Green VI = Violet
GR = Grey WS = White

EN/33Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
13. Circuit diagram for the basic wiring harness A in E39/2 cars
Legend
F1*Floating fuse holder near the left tail light
X001*Socket contact
X002*Black 18-pin plug casing
X003*Socket contact
A1*Console aerial connector
A4*Black 18-pin socket casing
A5*Black 3-pin socket casing; cable compensator
A7*Boot aerial connector
A12*White 12-pin plug casing
A13*White 12-pin socket casing
N9Radio
X322Black, 12-pin plug connector; audio hi-fi
X13016Cable eyelet, 6 mm in diameter; earth
X13598Black 12-pin plug casing
X181268-pin plug casing
X18507Black 3-pin connection plug; microphone
1)To power supply wiring harness B
2)To hands-free system wiring harness
3)To be tied back on the standard wiring harness
The components and X designations marked with an asterisk (*) are only valid for this circuit
diagram.
All the other components and X designations correspond to BMW after-sales circuit diagrams
Colour abbreviations
BL = Blue OR = Orange
BR = Brown OR = Orange
GE = Yellow SW = Black
GN = Green VI = Violet
GR = Grey WS = White