2001 Acura RL bulb

Indicator Lights

Door and Brake Lamp Monitor
The appropriate light comes on in this display if the trunk or any door
is not closed tightly. If a brake light
does not work, the BRAKE LAMP
indicator comes on when you push
the brake pedal with the ignition switch ON (II).
A burned out brake light is a hazard when drivers behind you cannot tell
you are braking. Have your brake lights repaired right away.
All the lights in the monitor display come on for a few seconds when you
turn the ignition switch ON (II). Turn Signal and
Hazard Warning
Indicators
The left or right turn signal light blinks when you signal a lane changeor turn. If the light does not blink or
blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page 250 ). Replace the bulb as
soon as possible, since other drivers
cannot see that you are signalling.
When you turn on the Hazard
Warning switch, both turn signal lights blink. All turn signals on theoutside of the vehicle should flash.
Low Fuel Indicator
This light comes on as a reminder that you must refuel soon. High Beam Indicator
This light comes on with the high beam headlights. See page 63 forinformation on the headlight

controls.

On Canadian models, this indicator
comes on with reduced brightness
when the Daytime Running Lights (DRL) are on (see page 65 ).
"Daytime Running
Lights" Indicator

Canadian models only

This indicator lights when you turn the ignition switch to ON (II) with
the headlight switch off and the
parking brake set. It should go off if
you turn on the headlights or release the parking brake. If it comes on at
any other time, it means there is a
problem with the DRL. There may also be a problem with the high
beam headlights.

Instruments and Controls
D R L

Maintenance

This section explains why it is important to keep your car well
maintained and to follow basic
maintenance safety precautions.
This section also includes Maintenance Schedules for normal
driving and severe driving conditions,
a Maintenance Record, and instruc-
tions for simple maintenance tasks
you may want to take care of
yourself.
If you have the skills and tools to per-
form more complex maintenance
tasks on your Acura, you may want
to purchase the Service Manual. See
page 319 for information on how to obtain a copy, or see your Acura

dealer.
Maintenance Safety....................... 204
Important Safety Precautions.. 205
Maintenance Schedule.................. 206
Required Maintenance Record.... 213 Owner Maintenance Checks........ 215
Fluid Locations............................... 216

Engine Oil...................................... 217
Adding Oil................................... 217
Recommended Oil.................... 217
Synthetic Oil.............................. 218

Additives.................................... 218

Changing the Oil and Filter...... 219
Cooling System.............................. 221 Adding Engine Coolant............. 221Replacing Engine Coolant........ 223
Windshield Washers..................... 227
Automatic Transmission Fluid..... 228 Differential Oil.............................. 229

Brake Fluid.................................... 230
Brake System............................. 230
Power Steering............................... 230

Hood Latch.................................... 231

Air Cleaner Element...................... 231 Spark Plugs..................................... 233

Replacement.............................. 233
Specifications............................ 236
Battery............................................ 236
Wiper Blades.................................. 239
Air Conditioning System............... 241
Air Conditioning Filter.................. 242
Drive Belts...................................... 242
Timing Belt..................................... 243
Tires................................................ 243
Inflation..................................... 243

Inspection................................... 245
Maintenance............................... 246
Tire Rotation.............................. 246
Replacing Tires and Wheels .... 247
Wheels and Tires....................... 248
Winter Driving........................... 248
Snow Tires............................ 249

Tire Chains.............................
249
Lights.............................................. 250 Replacing Bulbs......................... 252
Storing Your Car............................

261

Maintenance

Lights

Check the operation of your car's
exterior lights at least once a month.
A burned out bulb can create an unsafe condition by reducing yourcar's visibility and the ability to
signal your intentions to other

drivers.

Maintenance
HIGH BEAM HEADLIGHT


LOW BEAM HEADLIGHT
FRONT FOG LIGHT
TURN SIGNAL/
PARKING LIGHT
SIDE MARKER LIGHT

Lights

Check the following: Headlights (low and high beam)
Fog lights
Parking lights
Taillights
Brake lights
Turn signals Back-up lights
Hazard light function License plate light
Side marker lights
High-mount brake light
Daytime running lights (Canadian

models)

If you find any bulbs are burned out,

replace them as soon as possible.

Refer to the chart on page 303 to

determine what type of replacement

bulb is needed.

Maintenance
HIGH-MOUNT BRAKE LIGHT
TURN SIGNAL LIGHT

LICENSE PLATE

LIGHTS

STOP/TAIL LIGHTS

BACK-UP LIGHT

Lights

Replacing a High Beam Headlight
Bulb
The low beam headlight bulbs are a type of high voltage discharge tube.
High voltage can remain in the
circuit even with the light switch off
and the key removed. Because of
this, you should not attempt to examine or change a low beam
headlight bulb yourself. If a low
beam headlight bulb fails, take the
car to your dealer to have it replaced. Halogen bulbs are used for the high
beam headlight bulbs. When replacing a high beam headlight bulb,
handle it by its base and protect the
glass from contact with your skin or
hard objects. If you touch the glass, clean it with denatured alcohol and a
clean cloth.

Halogen bulbs get very hot when lit. Oil,

perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
1. Open the hood.
2. Remove the electrical connector
from the bulb by pulling the connector straight back.

3. Remove the rubber weather seal

by pulling on the tab.

Maintenance
NOTICE

Lights

4. Unclip the end of the hold-down
wire from its slot. Pivot it out of
the way and remove the bulb.

5. Insert the new bulb into the hole,

making sure the bulb is right side
up and the nubs on the bulb base
fit in the indentations in the headlight assembly. Pivot the hold-
down wire back in place and clip
the end into the slot.

6. Install the rubber seal over the

back of the headlight assembly.
Make sure it is right side up; it is
marked

7. Push the electrical connector onto

the new bulb.
Turn on the headlights to test the new bulb.

Replacing a Fog Light Bulb
Your car uses halogen fog light bulbs. See page 252 for informationon replacing a halogen bulb.

CONTINUED

Maintenance

WEATHER SEAL
BULB
CONNECTOR

HOLD-DOWN WIRE

Lights

1. Use a wrench to loosen the light
assembly's mounting bolt.

2. Remove the light assembly from
the bumper.

3. Remove the electrical connector
from the bulb by pulling the
connector straight back.
4. Remove the rubber weather seal
by pulling on the tab.
5. Unclip the end of the hold-down wire from its slot. Pivot the wireout of the way and remove the

bulb.
6. Insert the new bulb into the hole,
making sure the bulb is right side
up and the nubs on the bulb base
fit in the indentations in the fog light assembly. Pivot the hold-down wire back in place and clip
the end into the slot.
7. Install the rubber seal over the back of the fog light assembly.
Make sure it is right side up; it is marked
8. Push the electrical connector onto the new bulb. Turn on the front
fog lights to test the new bulb.
9. Put the light assembly into the bumper. Tighten the mounting

bolt.

Maintenance
CONNECTOR
BOLT WEATHER SEAL
BULB
HOLD-DOWN
WIRE

Lights

Replacing Front Turn Signal/ Parking and Side Marker Light
Bulbs
1. If you are changing the bulb on the driver's side, start the engine,
turn the steering wheel all the way
to the right, and turn off theengine. If you are changing the
bulb on the passenger's side, turn
the steering wheel to the left. 2. Use a flat-tipped screwdriver to
remove the holding clip from the
inner fender.
3. Pull the inner fender cover back.
4. Remove the socket from the headlight assembly by turning itone-quarter turn counterclockwise. 5. To remove the front turn signal/
parking light bulb, push it inslightly and turn it
counterclockwise. To remove the side marker bulb, pull it straight
out of its socket.
6. Install the new bulb into the
socket.

7. Insert the socket back into the headlight assembly. Turn itclockwise to lock it in place.
8. Test the lights to make sure the new bulb is working.
9. Put the inner fender cover in place. Install the holding clip. Lock it in
place by pushing on the center.
Maintenance

HOLDING CLIP