Page 139 of 333
Audio System
AM/FM/Cassette Stereo Audio
System
Your Acura's audio system provides
clear reception on both AM and FM
bands, while the preset buttons allow
you to easily select your favorite
stations.
The cassette system features Dolby*
noise reduction, automatic sensing of
chromium-dioxide (CrO 2) tape, and
autoreverse for continuous play.
* Dolby noise reduction manufactured under
license from Dolby laboratories Licensing Corpo-
ration. "DOLBY" and the double-D symbol are trademarks of Dolby laboratories
Licensing Corporation.
The anti-theft feature will disable the system if it is disconnected from the
car's battery. To get the system
working again, you must enter a
code number (see page 164).
Comfort and Convenience Features3.5 RL with Navigation System3.5 RL without Navigation System
Page 140 of 333
Audio System
3.5 RL without Navigation System
Operating the Radio
The ignition switch must be in
ACCESSORY (I) or ON (II) to operate the audio system. Turn thesystem on by pushing the PWR/
VOL knob or the AM/FM button.
Adjust the volume by turning the
knob.
The band and frequency that the ra- dio was last tuned to is displayed. To
change bands, press the AM/FM but-
ton. On the FM band, ST will be dis-
played if the station is broadcasting in stereo. ST will flash if you are driv-
ing in an area where the radio signal
is weak. Stereo reproduction on AM
is not available. You can use any of three methods to
find radio stations on the selected
band: TUNE, SEEK, or the Preset
buttons.
TUNE — Use the TUNE knob to tune the radio to a desired frequency.
Turn the TUNE knob to the right to tune to a higher frequency, or to the
left to tune to a lower frequency.
Turn the knob right or left until the display reaches the desired
frequency.
SEEK — The SEEK function searches the band for a station with
a strong signal. To activate it, push ei-
ther side of the SEEK/SKIP buttons (— or +). Push the + button to
scan up from the current frequency,
and the — button to scan down. It
stops when it finds a station with a
strong signal.
Preset — You can store the
frequencies of your favorite radio
stations in the six preset buttons.
Each button will store one frequency
on the AM band, and two
frequencies on the FM band.
CONTINUED
Comfort and Convenience Features
Page 141 of 333
Audio System
To store a frequency:
1. Select the desired band, AM or FM. FM1 and FM2 let you store
two frequencies with each Preset
button.
2. Use the TUNE or SEEK function to tune the radio to a desired
station.
3. Pick the Preset button you want for that station. Press the buttonand hold it until you hear a beep.
4. Repeat steps 1 to 3 to store a total of six stations on AM and twelve
on FM.
Once a station's frequency is stored,
simply press and release the proper
Preset button to tune to it.
The preset frequencies will be lost if your car's battery goes dead, isdisconnected, or the radio fuse is
removed.
AM/FM
BUTTON
PWR/VOL
KNOB
SEEK/SKIP
BUTTONS
PRESET BUTTONS
Comfort and Convenience Features
STEREO
INDICATOR
TUNE
KNOB
Page 142 of 333
Audio System
AUTO SELECT — If you are traveling far from home and can no
longer receive the stations you
preset, you can use the Auto Select
feature to find stations in the local
area.
To activate Auto Select, press the
A. SELECT button. A. SELECT will appear in the display, and the system
will go into scan mode for several seconds. It automatically scans both
bands, looking for stations with strong signals. It stores the frequen-
cies of six AM stations and twelve
FM stations in the preset buttons.
You can then use the preset buttons to select those stations.
If you are in a remote area. Auto
Select may not find six strong AM
stations or twelve strong FM stations.
If this happens, you will see a "0"
displayed when you press any preset
button that does not have a station stored. With Auto Select on, you cannot
manually store any frequencies in
the preset buttons. If you do not like
the stations found by Auto Select,
you can use the TUNE and SEEK
functions to find other stations.
Auto Select does not erase the
frequencies that you preset pre-
viously. When you return home, turn
off Auto Select by pressing the
A. SELECT button. The preset
buttons will then select the fre-
quencies you originally set.
Comfort and Convenience Features
AUTO SELECT INDICATOR
PRESET BUTTONS
SEEK/SKIP
BUTTONS
TUNE
KNOB
AUTO SELECT BUTTON
AM/FM BUTTON
Page 143 of 333
Audio System
Adjusting the Sound
Balance/Fader — These twocontrols adjust the strength of the
sound coming from each speaker.
The Balance control adjusts the side- to-side strength, while the Fadercontrol adjusts the front-to-back
strength.
To adjust the fader, push on the BASS/FADER control knob to get it
to pop out. Pull it out slightly farther, and adjust the front-to-back sound to
your liking. Push the knob back in when you are done so you cannotchange the setting by accidentally
bumping it.
To adjust the balance, push on the
TREBLE/BALANCE control knob to get it to pop out. Pull it out slightly
farther, and adjust the side-to-sidesound to your liking. Push the knob
back in when you are done so you
cannot change the setting by
accidentally bumping it. Treble/Bass — Use these controls
to adjust the tone to your liking.
To adjust the Treble level, push on the TREBLE/BALANCE control
knob to get it to pop out. Without
pulling it out farther, turn the knob
to adjust the treble level. Push the
knob back in when you are done so
you cannot change the setting by accidentally bumping it. To adjust the Bass level, push on the
BASS/FADER control knob to get it
to pop out. Without pulling it out
farther, turn the knob to adjust the bass level. Push the knob back in
when you are done so you cannot change the setting by accidentally
bumping it.
Comfort and Convenience Features
BASS/FADER
CONTROL
TREBLE/BALANCE
CONTROL
Page 144 of 333
Audio System
Audio System Lighting
You can use the instrument panel brightness control dial to adjust the il-
lumination of the audio system (see
page 66). The audio system illuminates when the parking lightsare on, even if the radio is turned off.
Radio Frequencies and Reception
For information, See page 149.
Operating the Cassette Player
The ignition switch must be in
ACCESSORY (I) or ON (II). Make sure the tape opening on the
cassette is facing to the right, then
insert the cassette most of the way
into the slot. The system will pull it
in the rest of the way, and begin to
play.
The tape direction indicator will light to show you which side of the cassette is playing. The indicates
the side you inserted facing upward is now playing. If you want to play
the other side, press the PROG/ PLAY button.
Dolby noise reduction turns on when
you insert a cassette. If the tape was not recorded with Dolby noise reduc-
tion, turn it off by pressing the
button.
When the system reaches the end of
the tape, it will automatically reversedirection and play the other side. If
you want to remove the cassette
from the drive, press the EJECT button.
If you turn the system off while a
tape is playing, either with the PWR/ VOL knob or by turning off the
ignition, the cassette will remain in
the drive. When you turn the system
back on, the tape will begin playing
where it left off.
To switch to the radio or CD changer while listening to a tape,
press the AM/FM or CD/TAPE but-
ton. To change back to the cassette
player, press the CD/TAPE button.
Comfort and Convenience Features
Page 145 of 333
Audio System
Tape Search Functions
With a cassette playing, you can usethe FF, REW, TMS, or REPEAT
function to find a desired program.
FF/REW — Fast Forward and Re-
wind move the tape rapidly. To re- wind the tape, push the REW button.
You will see REW in the display. To fast forward the tape, push the FFbutton. You will see FF displayed.
Press the PROG/PLAY button to
take the system out of rewind or fast
forward. When the system reaches the end of the tape, it reversesdirection and begins to play if in fast
forward, or it begins to play if in
rewind.
Comfort and Convenience Features
AM/FM BUTTON
CASSETTE SLOT
PWR/VOL KNOB
TMS INDICATOR
DOLBY INDICATOR
EJECT
BUTTON
REPEAT
INDICATOR
REPEAT
BUTTON
TMS BUTTON
DOLBY BUTTON
PROG/PLAY
BUTTON
TAPE
DIRECTION
INDICATOR
REWIND
BUTTON
CD/TAPE BUTTON
FAST FORWARD
BUTTON
Page 146 of 333
Audio System
TMS — The Tape Music Search Function allows you to find the begin-
ning of a song or passage. To acti-
vate TMS, press the TMS button.
You will see TMS displayed. To find the beginning of the song or passagecurrently playing, push the REW but-
ton. You will see REW flashing in the
display as the tape rewinds. To find
the beginning of the next song, push
the FF button. You will see FF
flashing in the display as the tape
fast forwards. When the system
finds the beginning of a song or pas- sage, it goes back to PLAY mode.
Press the TMS button again to turn
it off.
CONTINUED
Comfort and Convenience Features
CASSETTE SLOT
PWR/VOL KNOB TMS INDICATOR
TAPE DIRECTION
INDICATOR
EJECT
BUTTON
REPEAT
INDICATOR
TMS BUTTON REPEAT
BUTTON
FAST FORWARD BUTTON
REWIND
BUTTON
