2001 Acura Integra lock

Light
s

Replacin g Fron t Tur n Signal /
Parkin g an d Sid e Marke r Ligh t
Bulb s
1. Use a Phillips-head screwdriver to loosen the light assembly'smounting screw.
2. Remove the light assembly from the bumper. 3. Remove the socket of the burned-
out bulb from the light assembly
by turning it one-quarter turn counterclockwise.
4. To remove the front bulb, push it in slightly and turn it counterclock-
wise. To remove the side bulb, pull it straight out of its socket. 5. Install the new bulb in the socket.
6. Insert the socket back into the light assembly. Turn it clockwise
to lock it in place.
7. Test the lights to make sure the new bulb is working.
8. Put the light assembly into the bumper. Make sure the tab on thelight assembly fits into the bumperslot. Tighten the mounting screw.

Maintenanc e
SCRE
W

Light
s

Replacin g a High-moun t Brak e
Ligh t Bul b
LS model
1. Undo the cover fasteners by pushing on the center of each
fastener's head until it pops in. Remove the cover.
2. Determine which bulb is burned out. 3. Pull the bulb straight out of its

socket.

Push the new bulb straight into
the socket until it bottoms.
4. Test the lights to make sure the new bulb is working. 5. Reset each fastener by pushing on
the pointed end until it pops backalmost flush with the fingers on
the housing.
6. Reinstall the cover. Secure each fastener by pushing on the centeruntil it locks (the center is flush
with the head).
Maintenance

Light
s
Replacin g Rea r Tur n Signa l an d
Sid e Marke r Ligh t Bulb s
1. Open the hatch and remove the light assembly cover by pulling the
edge.

2. Remove the socket from the light assembly by turning it one-quarter
turn counterclockwise. 3. If the turn signal light bulb is
burned out, remove it by pushingit in and turning counterclockwise.
If the side marker light bulb is
burned out, remove it by pulling it straight out of its socket.
4. Install the new bulb in the reverse order of removal.
5. Push the socket into the light assembly and turn it clockwise
until it locks.
6. Test the lights to make sure the new bulb is working.
7. Install the light assembly cover. Make sure it locks in place. Replacin
g Tail/Stopligh t an d
Back-u p Ligh t Bulb s
1. Open the hatch. Remove the tether hardware cover with a small
flat-tip screwdriver and tetheranchor plate with a wrench by
turning the bolt counterclockwise.
When reinstalling tether hardware, see Protectin g Childre n on page

41.

On Type-R model
You cannot replace these bulbs
yourself, contact your Acura dealer.
Maintenanc e

Light
s

2. Undo the seven cover fasteners by pushing on the center of each
fastener's head until it pops in. Remove the taillight cover panel. 3. Remove the socket by turning it
one-quarter turn counterclockwise. 4. Try the tail/stoplights and back-up
light to verify which bulb needs
replacing. Remove the bulb by
turning it counterclockwise.
5. Install the new bulb in the socket. Test it to make sure it works.
6. Reinstall the socket into the light
assembly.

7. Reinstall the tether anchor hardware.
Make sure the toothed washer is
on the bottom of the bolt. Tighten
the bolt to:
16 lbf.ft (22 N.m,2.2 kgf.m)
If a torque wrench was not used,

see your Acura dealer as soon as

possible to verify proper

installation.

CONTINUED
Maintenanc e

Light
s

8. Reset each fastener by pushing on the pointed end until it pops backalmost flush with the fingers on
the housing.
9. Reinstall the cover. Secure each fastener by pushing on the center
until it locks (the center is flush
with the head). Replacin
g a Rea r Licens e Plat e
Bul b
1. Remove the two screws and remove the license plate light
assembly.

2. Remove the socket from the light assembly by turning it one-quarter
turn counterclockwise.
3. Pull the bulb straight out of its socket. Push the new bulb in until
it bottoms in the socket.
4. Turn on the parking lights and
check that the new bulb is

working.

5. Reinstall the license light assem-
bly. Install the two screws and

tighten them securely.

Maintenanc e

Storin
g You r Ca r
If you need to park your car for an
extended period (more than one
month), there are several things you should do to prepare it for storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your car back on the road. If
possible, store your car indoors. Fill the fuel tank.
Change the engine oil and filter
(see page 175). Wash and dry the exterior

completely.
Clean the interior. Make sure the
carpeting, floor mats, etc. are
completely dry.
Leave the parking brake off. Put
the transmission in Reverse
(5-speed manual) or Park
(automatic).
Block the rear wheels.
If the car is to be stored for a
longer period, it should be
supported on jackstands so the
tires are off the ground. Leave one window open slightly (if
the car is being stored indoors). Disconnect the battery.
Support the front and rear wiper
blade arms with a folded towel or
rag so they do not touch the

windshield.
To minimize sticking, apply a
silicone spray lubricant to all door
and hatch seals. Also, apply a body
wax to the painted surfaces that mate with the door and hatch seals. Cover the car with a "breathable"
cover, one made from a porous
material such as cotton. Nonporous materials, such as
plastic sheeting, trap moisture,
which can damage the paint. If possible, run the engine for a
while periodically (preferably once a month).
If you store your car for 12 months or longer, have your Acura dealer
perform the inspections called for in
the 24 months/30,000 miles (48,000
km) maintenance schedule (Normal Conditions) as soon as you take it
out of storage (see page 164). The
replacements called for in the
maintenance schedule are not
needed unless the car has actually
reached that time or mileage.
Maintenanc e

Changin
g a Fla t Tir e
If you have a flat tire while driving, stop in a safe place to change it.
Stopping in traffic or on the shoulder
of a busy road is dangerous. Driveslowly along the shoulder until you
get to an exit or an area to stop that is far away from the traffic lanes.
JAC
K

SPAR E TIR E

TOOL KI T

1. Park the car on firm, level and non-slippery ground away from
traffic. Put the transmission in Park (automatic) or Reverse (manual). Apply the parking brake.
If you are towing a trailer, unhitch
the trailer. 2. Turn on the hazard warning lights
and turn the ignition switch to
LOCK (0). Have all the
passengers get out of the car while
you change the tire.
3. Open the hatch. Pull up the floor mat and remove the spare tire
cover.

4. Take the tool kit out of the spare tire well.
5. Unscrew the wing bolt and take the spare tire out of its well.

CONTINUED

Takin g Car e o f th e Unexpecte d

The car can easily roll off the

jack, seriously injuring anyone
underneath.

Follow the directions for

changing a tire exactly, and never get under the car when it
is supported only by the jack.

Changin
g a Fla t Tir e
6. Turn the jack's end bracket counterclockwise to loosen it, then
remove the jack. 7. (Except Type-R)
Loosen the four wheel nuts 1/2
turn with the wheel wrench.
(Type-R)
Loosen the five wheel nuts 1/2
turn with the wheel wrench. 8. Find the jacking point nearest the
wheel you are removing. Place the
jack under the jacking point. Turn the end bracket clockwise until
the top of the jack contacts the
jacking point. Make sure the
jacking point tab is resting in the
jack notch.

Takin g Car e o f th e Unexpecte d

JAC
K
WHEEL WRENC H
JACKIN
G POIN T