2001.5 PEUGEOT 106 ignition

INSTRUMENTS AND CONTROLS25
Service intervals If your vehicle is used in certain par-
ticularly difficult conditions it isnecessary to follow the "Arduousconditions" servicing schedule,which involves shorter intervals bet-
ween services (see the Warrantyand Maintenance Record booklet). Comment:If the time limit between
two services is reached before the relevant mileage limit, the servicespanner symbol will light up and thedisplay will show 0.
To change the service interval
- Switch off the ignition.
- Press and hold button 1. -
Switch on the ignition.
- Release the button straight away.
- The service interval is displayed.
- Each time button 1is pressed
brießy, the service intervals are alternated.
Example - When the required service interval is displayed, press button 1for
10 seconds to confirm (theselected service interval ßashes
for 10 seconds).
Release the button to conÞrm whenthe display stops ßashing. Reset to zero Y
our PEUGEOT dealer will carry out
this operation after each service.
However, if you carry out your service yourself, the zero resetprocedure is as follows:
- switch off the ignition,
- press and hold button 1,
- switch on the ignition,- keep button 1pressed for
10 seconds,
the display indicates [= 0]and the
service spanner symbol disappears.
1
06-05-2002

INSTRUMENTS AND CONTROLS25
Service intervals If your vehicle is used in certain par-
ticularly difficult conditions it isnecessary to follow the "Arduousconditions" servicing schedule,which involves shorter intervals bet-
ween services (see the Warrantyand Maintenance Record booklet). Comment:If the time limit between
two services is reached before the relevant mileage limit, the servicespanner symbol will light up and thedisplay will show 0.
To change the service interval
- Switch off the ignition.
- Press and hold button 1. -
Switch on the ignition.
- Release the button straight away.
- The service interval is displayed.
- Each time button 1is pressed
brießy, the service intervals are alternated.
Example - When the required service interval is displayed, press button 1for
10 seconds to confirm (theselected service interval ßashes
for 10 seconds).
Release the button to conÞrm whenthe display stops ßashing. Reset to zero Y
our PEUGEOT dealer will carry out
this operation after each service.
However, if you carry out your service yourself, the zero resetprocedure is as follows:
- switch off the ignition,
- press and hold button 1,
- switch on the ignition,- keep button 1pressed for
10 seconds,
the display indicates [= 0]and the
service spanner symbol disappears.
1
06-05-2002

YOUR 106 IN DETAIL28
GENERAL FUNCTIONS On / off
With the ignition key in the ACCESSORIES or IGNITION position, press the "M"button to switch the set on or off.
ANTI-THEFT SYSTEM
The first time you use the set following disconnection of the set or the battery, you must enter the confidential code which was given to you on handover of your vehicle. Entering the code Switch the set on. The display shows "CODE"then the set changes over to code request mode and "- - - -"is displayed.
Enter your four-digitcode number using buttons "1"to "6" .
For example : if your code is 5345 press buttons "5", "3" , "4" and "5"in turn.
When the fourth number has been entered correctly, the radio starts automatically.
Error in entering the code
If an error is made when entering one of the first three digits, do not continue the operation and switch off the radio to prevent blocking it. Each incorrect code entry will result in the set being blocked for a period of from 5 seconds to 30 minutes, after
the 7th incorrect entry.
To unblock the set, leave it switched on during the waiting period. When "- - - -"is displayed, you can enter the
code again.
If the set is switched off during the waiting period, this waiting period will restart when the set is switched on again. After 14 incorrect code entries, the radio will be permanently blocked and the message “END”will be displayed.
ADJUSTING THE SOUND Adjusting the volume T urn the "M"button to increase or decrease the volume of the set.
If the radio overheats, the volume will reduce. Note: If you have a car-phone fitted with a ÒmuteÓsignal output connected to the set, the set will automatically
change to ÒmuteÓwhen the car-phone is used.
06-05-2002

YOUR 106 IN DETAIL38
GENERAL FUNCTIONS On / off
With the ignition key in the ACCESSORIES or IGNITION position, press the "M"button to switch the set on or off.
The set can operate for 30 minutes without switching the ignition on. ANTI-THEFT SYSTEM
The first time you use the set following disconnection of the set or the battery, you must enter the confidential code which was given to you on handover of your vehicle. Entering the code Switch the set on. The display shows "CODE" then the set changes over to code request mode and "- - - -" is displayed.
Enter your four-digitcode number using buttons "1" to "6" .
For example: : if your code is 5345 press buttons "5", "3" , "4" and "5"in turn.
When the fourth number has been entered correctly, the radio starts automatically.
Error in entering the code
If an error is made when entering one of the first three digits, do not continue the operation and switch off the radio to prevent blocking it. Each incorrect code entry will result in the set being blocked for a period of from 5 seconds to 30 minutes, after
the 7th incorrect entry.
To unblock the set, leave it switched on during the waiting period. When "- - - -"is displayed, you can enter the
code again.
If the set is switched off during the waiting period, this waiting period will restart when the set is switched on again. After 14 incorrect code entries, the radio will be permanently blocked and the message “END”will be displayed.
ADJUSTING THE SOUND Adjusting the volume T urn the "M"button to increase or decrease the volume of the set.
If the radio overheats, the volume will reduce. Note: If you have a car-phone fitted with a ÒmuteÓsignal output connected to the set, the set will automatically
change to ÒmuteÓwhen the car-phone is used.
06-05-2002

YOUR 106 IN DETAIL54
Seat belts (5-door):
To adjust the height of the front
seat belts*:
Pull control 1towards you and slide it.
To fasten the seat belts:
Pull the strap, then insert the end into the buckle. Rear seat beltsThe rear seats are Þtted with two three-point inertia reel belts and alap belt.
1
To be effective, a seat
belt must be tensioned as close to the body aspossible.
Depending on the nature andseriousness of the impact thepre-tensioning system may betriggered before and indepen-dently of the airbags. In all cases, the airbag warning light comes on. Following an impact, have the system checked by a PEUGEOT
dealer. The system has been designed to be fully operational for tenyears. Have it replaced at the endof this period.Pre-tensioning and force- limiting front seat belts* Safety in the event of a front impact has been improved by theintroduction of pre-tensioning andforce-limiting front seat belts.Depending on the seriousness ofthe impact, the pre-tensioningsystem instantly tightens the seatbelts Þrmly against the body of theoccupant. The pre-tensioning seat belts are armed when the ignition is on. * According to speciÞcation
06-05-2002

YOUR 106 IN DETAIL55
Key position There are four positions of the ignition key in the lock: "S" Stop: ignition is off.
"A" Accessories: ignition is off but
accessories can operate. The battery charge warning lamp lights. "M" Run: ignition on. The following
warning lamps light:- low engine oil pressure,
- coolant temperature,
- battery charge,
- pre-heater (DIESEL),
- handbrake, low brake ßuid,
- engine diagnostics*, -
ABS* (lights for 3 seconds, the warning lamp should always goout when the vehicle speed isover 8 m.p.h. [12 km/h]),
- Airbag*, the warning lamp lightsfor six seconds, then goes out.
"D" Starter: starts the engine.
The following warning lamps go out: - low engine oil pressure,
- battery charge,
- engine diagnostics*. Starting Unlock the steering T
urn the steering wheel gently
while turning the key. Before starting it is advisable to: Press the clutch pedal while opera- ting the starter to aid starting of theengine. * According to speciÞcation
06-05-2002

YOUR 106 IN DETAIL55
Key position There are four positions of the ignition key in the lock: "S" Stop: ignition is off.
"A" Accessories: ignition is off but
accessories can operate. The battery charge warning lamp lights. "M" Run: ignition on. The following
warning lamps light:- low engine oil pressure,
- coolant temperature,
- battery charge,
- pre-heater (DIESEL),
- handbrake, low brake ßuid,
- engine diagnostics*, -
ABS* (lights for 3 seconds, the warning lamp should always goout when the vehicle speed isover 8 m.p.h. [12 km/h]),
- Airbag*, the warning lamp lightsfor six seconds, then goes out.
"D" Starter: starts the engine.
The following warning lamps go out: - low engine oil pressure,
- battery charge,
- engine diagnostics*. Starting Unlock the steering T
urn the steering wheel gently
while turning the key. Before starting it is advisable to: Press the clutch pedal while opera- ting the starter to aid starting of theengine. * According to speciÞcation
06-05-2002

YOUR 106 IN DETAIL56
Starting a petrol engine* Do not press the accelerator pedal. Operate the starter without relea- sing the key until the engine starts. * According to speciÞcationStarting a diesel engine Engine cold: Do not press the accelerator pedal. T
urn the key to position “M”, the
pre-heat warning lamp lights.W ait until the warning lamp goes
out, then operate the starter in posi- tion “D” until the engine runs
smoothly.
Engine hot: Do not press the accelerator pedal.
Operate the starter.If the engine stops or does not start
immediately, always wait a fewseconds before trying again using
the pre-heater.Never race a cold engi- ne.
Never run the engine inan enclosed space. If the engine cannot be
stopped using the ignition key, press the brake pedal, engage agear and release the clutch inorder to stall the engine. Do not modify the steering
lock in any way.
NOTE: according to speci fica-
tion, the pre-heat warning lamp does not light if the engi-ne is suf ficiently hot.
06-05-2002