2001.5 Peugeot 106 Dag change wheel

P R A C T I C A L I N F O R M AT I O N7979
Visual brake pad wear indicator* The front brakes are Þtted with visual wear indicators. Regularly check the thickness of the brake pads.
To check: turn the wheels to full lock on the side to be checked. The thickness of pad remaining is represented by the measu- rement X. When the measurement is zero, the brake pads must be changed. Advice As brake pad wear depends on the way in which the vehicle is driven, particularly if the vehicle is used for urban driving or for
short journeys, or is driven in a very sporty manner, it may be necessary to check the thickness of the pads even between ser- vice intervals. * According to speciÞcation
06-05-2002

P R A C T I C A L I N F O R M AT I O N8080
3
2
1
CHANGING A WHEEL Access to the spare wheel The spare wheel is outside, under the luggage compartment, in a
metal carrier.
Ð Take out the wheel-brace 1.
Ð Using the wheel-brace 1, slacken
the spare wheel carrier bolt inside the luggage compartment,under the carpet.
ÐL
ift the carrier to disengage the
hook towards the rear, then lower it.
Ð Take out the jack storage box 2
located in the spare wheel. Remove the wheel
Ð Use the wheel-brace to remove
the wheel trim by pulling at the valve location.
Ð Loosen the wheel bolts. Ð
Use the jack storage box to chock the wheel at the opposite corner tothe wheel being changed.
Ð Position the jack head in the jac- king point nearest to the wheelbeing changed, taking care thatthe entire base of the jack is incontact with the ground.
Ð Raise the jack, remove the wheel bolts and remove the wheel. Fit the spare wheel
Ð Position the wheel, then lightly
pre-tighten the bolts using the wheel-brace.
Ð Lower the jack and release it.
Ð Tighten the bolts using the wheel-brace.
Ð Fit the wheel trim, starting with the valve location, and press with the palm of the hand.
Replacing the wheel in the carrier
Ð Lift the wheel to aid re-positio- ning of the carrier.
Ð Do not forget to retighten the spare wheel carrier bolt.
06-05-2002

P R A C T I C A L I N F O R M AT I O N8181
For your safety, always change a wheel:
Ð on level, solid, non-slippery ground,
Ð with the handbrake applied, Ð
with Þrst or reverse gear engaged,
Ð Chock the vehicle.
Ð Never position yourself under a vehicle which is supported only by a jack. Use a ramp.
After changing the wheel
Ð Have the wheel bolts and the tyre pressure checked as soon as possible.
Ð Have the damaged tyre repaired so that it can bereturned to the vehicle assoon as possible.
Ð The Òspace-savingÓ* type of spare wheel is Þtted with a
115/70R 15 tyre and is for
temporary use only.
- Pressure: 61 lbf. in 2
(4.2 bars).
- Maximum speed: 50 m.p.h. (80 km/h).
* According to speciÞcation
3
Special procedure for Sport model Positioning the jack
Ð Close the jack completely.
Ð Position the jack under the vehicle at the jacking points tilting it by 90¡, so that the jack handle hinge is at the same height as the sill trim, then straighten it.
Ð Check that the jack is in correct contact with the sill. Replacing the wheel in the carrier
Ð Position the jack storage box with the arrow pointing forwards.
Never place the jack in contact with the sill trim.
06-05-2002

Direction indicator bulbs PY21W Access to the bulbs is from inside the wheel arch.
Turn the wheels to full lock (to the left to change the right hand bulband vice versa). Open the access ßap.
Turn the socket 1/4 turn.Change the bulb. Ensure that the ßap is closed
correctly.Side repeater W5W* Pull the rear part of the transparent
cover and detach the assembly. Support the connector and turn the transparent cover 1/4 turn. Change the bulb.
Rear lights Direction indicators
PY21W
Reversing lights P21W
Fog lamp P21W
Tail lights P5W
Brake/tail lights P21/5W
From inside the luggage com- partment: Remove the plastic protector 1.
Remove the air outlet grille 2using
a cross-head screwdriver. Slacken the two wing nuts 3and
release the light block 4.
Pinch the lugs 5to remove the
bulb-holder. Change the bulbs. * According to speciÞcation
P R A C T I C A L I N F O R M AT I O N84
4
3
1
2
5
06-05-2002

Direction indicator bulbs PY21W Access to the bulbs is from inside the wheel arch.
Turn the wheels to full lock (to the left to change the right hand bulband vice versa). Open the access ßap.
Turn the socket 1/4 turn.Change the bulb. Ensure that the ßap is closed
correctly.Side repeater W5W* Pull the rear part of the transparent
cover and detach the assembly. Support the connector and turn the transparent cover 1/4 turn. Change the bulb.
Rear lights Direction indicators
PY21W
Reversing lights P21W
Fog lamp P21W
Tail lights P5W
Brake/tail lights P21/5W
From inside the luggage com- partment: Remove the plastic protector 1.
Remove the air outlet grille 2using
a cross-head screwdriver. Slacken the two wing nuts 3and
release the light block 4.
Pinch the lugs 5to remove the
bulb-holder. Change the bulbs. * According to speciÞcation
P R A C T I C A L I N F O R M AT I O N84
4
3
1
2
5
06-05-2002

T E C H N I C A L D ATA102
For your PEUGEOT, only use accessories and original parts approved by the manufacturer.
These accessories and parts are all suitable for your PEUGEOT, after being tested and approved for reliability and
safety.
A wide choice of original accessories, approved by PEUGEOT, is available through the network.They all carry the PEUGEOT guarantee. Security:Anti-theft alarms, engraving of windows, wheel anti-theft devices, fog lamps...
Comfort: Air conditioning, telephone console, seat covers, carpets, luggage compartment tray, mud ßaps, sun roof*, luggage net, armrest, door deßectors, storage under the rear parcel shelf...
Communication: Audio equipment, telephone, CB, loud speakers, CD changer, navigation...
Personalisation: Tailgate spoiler, alloy wheels, Þnishers, steering wheels, sport exhaust...
Leisure: Towbar, roof bars, roof box, carriers (for bicycles, skis...)
Children: Booster seats and child seats, side blinds and rear blind...
Maintenance products: Windscreen wiper ßuid, internal and external cleaning and maintenance products...
* As the Þtting of a sun roof may involve cutting the roof strengthener, it is imperative that only original PEUGEOTproducts are used.
06-05-2002