2000 YAMAHA XVS1100A Owners Manual

INSTRUMENT AND CONTROL FUNCTIONS
3-8
3
EAU02917
Fuel tank cap To remove the fuel tank cap
Slide the lock cover open, insert the key
into the lock, and then turn it 1/4 turn
clockwise. The lock will be released
and the fuel tank cap can be removed.
To install the fuel tank cap
1. Insert the fuel tank cap into the
tank opening with the key inserted
in the lock and with the “ ” mark
facing forward. 2. Turn the key counterclockwise to
the original position, remove it,
and then close the lock cover.
NOTE:@ The fuel tank cap cannot be installed
unless the key is in the lock. In addition,
the key cannot be removed if the cap is
not properly installed and locked. @
EW000024
WARNING
@ Make sure that the fuel tank cap is
properly installed before riding. @
EAU01183
Fuel Make sure that there is sufficient fuel in
the tank. Fill the fuel tank to the bottom
of the filler tube as shown in the illustra-
tion.
EW000130
WARNING
@ l
Do not overfill the fuel tank, oth-
erwise it may overflow when the
fuel warms up and expands.
l
Avoid spilling fuel on the hot
engine.
@
1. Lock cover
2. “ ” mark
a. Unlock
b. Lock
1. Filler tube
2. Fuel level
E_5KS.book Page 8 Monday, August 21, 2000 10:48 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-9
3
EAU00185
CAUTION:@ Immediately wipe off spilled fuel
with a clean, dry, soft cloth, since
fuel may deteriorate painted surfac-
es or plastic parts. @
EAU00191
NOTE:@ If knocking (or pinging) occurs, use
gasoline of a different brand or with a
higher octane grade. @
EAU02969
Fuel cock The fuel cock supplies fuel from the
tank to the carburetors while also filter-
ing it.
The fuel cock lever positions are ex-
plained as follows and shown in the il-
lustrations.
OFF
With the fuel cock lever in this position,
fuel will not flow. Always turn the fuel
cock lever to this position when the en-
gine is not running.ON
With the fuel cock lever in this position,
fuel flows to the carburetors. Turn the
fuel cock lever to this position when
starting the engine and riding. Recommended fuel:
Regular unleaded gasoline with a
research octane number of 91 or
higher
Fuel tank capacity:
Total amount:
17 L
Reserve amount:
4.5 L1. Pointed end positioned over “OFF”Off position
1. Pointed end positioned over “ON”Normal position
E_5KS.book Page 9 Monday, August 21, 2000 10:48 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-10
3
RES
This indicates reserve. With the fuel
cock lever in this position, the fuel re-
serve is made available. Turn the fuel
cock lever to this position if you run out
of fuel while riding. When this occurs,
refuel as soon as possible and be sure
to turn the fuel cock lever back to “ON”!
EAU02973
Starter (choke) lever “ ” Starting a cold engine requires a richer
air-fuel mixture, which is supplied by
the starter (choke).
Move the lever in direction
a to turn on
the starter (choke).
Move the lever in direction
b to turn off
the starter (choke).
ECA00038
CAUTION:@ Do not use the starter (choke) for
more than 3 minutes as the exhaust
pipe may discolor from excessive
heat. In addition, extended use of
the starter (choke) will cause after-
burning. If this occurs, turn off the
starter (choke). @
1. Pointed end positioned over “RES”Reserve position
1. Starter (choke) lever “ ”
E_5KS.book Page 10 Monday, August 21, 2000 10:48 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-11
3
EAU01710
Seats (XVS1100) Passenger seat
To remove the passenger seatRemove the nut, and then pull the pas-
senger seat up.To install the passenger seat
Insert the projection on the front of the
passenger seat into the seat holder as
shown, place the seat in the original
position, and then install the nut.Rider seat
To remove the rider seat
1. Remove the passenger seat.
2. Remove the bolts and bracket,
and then pull the rider seat up.
1. NutXVS1100
1. Projection
2. Seat holderXVS1100
1. Bolt (´ 2)
2. BracketXVS1100
E_5KS.book Page 11 Monday, August 21, 2000 10:48 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-12
3
To install the rider seat
1. Insert the projections on the front
of the rider seat into the seat hold-
ers as shown, and then place the
seat in the original position.
2. Install the removed bracket and
bolts.
3. Install the passenger seat.NOTE:@ Make sure that the seats are properly
secured before riding. @
EAU03202
Seats (XVS1100A)Passenger seat
To remove the passenger seatRemove the bolt, and then pull the pas-
senger seat up.To install the passenger seat
Insert the projection on the front of the
passenger seat into the holder as
shown, place the seat in the original
position, and then install the bolt.
1. Projection (´ 2)
2. Seat holder (´ 2)XVS1100
1. BoltXVS1100A
1. Projection
2. Seat holderXVS1100A
E_5KS.book Page 12 Monday, August 21, 2000 10:48 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-13
3
Rider seat
To remove the rider seat
1. Remove the passenger seat.
2. Remove the bolt, and then pull the
rider seat up.To install the rider seat
1. Insert the projections on the front
of the rider seat into the holders as
shown, place the seat in the origi-
nal position, and then install the
bolt.
2. Install the passenger seat.NOTE:@ Make sure that the seats are properly
secured before riding. @
EAU00260
Helmet holder To open the helmet holder, insert the
key into the lock, and then turn the key
as shown.
To lock the helmet holder, place it in
the original position, and then remove
the key.
EW000030
WARNING
@ Never ride with a helmet attached to
the helmet holder, since the helmet
may hit objects, causing loss of
control and possibly an accident. @
1. BoltXVS1100A
1. Projection (´ 2)
2. Seat holder (´ 2)XVS1100A
1. Helmet holder
E_5KS.book Page 13 Monday, August 21, 2000 10:48 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-14
3
EAU01869
Storage compartment The storage compartment is located on
the left side of the motorcycle.To open the storage compartment
1. Slide the lock cover open, insert
the key into the lock, and then turn
it clockwise.2. Pull the storage compartment cov-
er out as shown.1. Storage compartment cover
2. Lock
1. Lock cover
1. Storage compartment cover
E_5KS.book Page 14 Monday, August 21, 2000 10:48 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-15
3
To close the storage compartment
1. Place the storage compartment
cover in its original position as
shown.
2. Turn the key counterclockwise, re-
move it, and then close the lock
cover.
EAU03194
Adjusting the shock absorber
assembly The shock absorber assembly is locat-
ed under the rider seat and is equipped
with a spring preload adjusting ring.
EC000015
CAUTION:@ Never attempt to turn an adjusting
mechanism beyond the maximum
or minimum settings. @Adjust the spring preload as follows.
1. Remove the rider seat. (See
page 3-11 [XVS1100] or 3-13
[XVS1100A] for rider seat removal
and installation procedures.)2. Remove each quick fastener from
the ignitor unit panel by pushing
the center in with a screwdriver,
then pulling the fastener out.
1. Storage compartment cover
1. Quick fastener (´ 3)
E_5KS.book Page 15 Monday, August 21, 2000 10:48 AM