R
6-10
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
NOTE:
ÒGL-4Ó is a quality and additive rating.
Hypoid gear oils rated ÒGL-5Ó or ÒGL-6Ó
may also be used.
5. Install and tighten the filler bolt to
the specified torque.
6. After replacing the final gear oil, be
sure to check for oil leakage. Final gear case capacity:
0.19 L
Recommended oil:
SAE 80 API GL-4 Hypoid gear oil
If desired, an SAE 80W90 hypoid
gear oil may be used for all
conditions.
Tightening torque:
Oil filler bolt:
23 Nm (2.3 mákg)
1. Fuel tank
2. Bolt (´ 3)
EAU02998
Air filter
The air filter should be cleaned at the
specified intervals. It should be cleaned
more frequently if you are riding in un-
usually wet or dusty areas.
1. Remove the seats. (See page 3-7
for seat removal and installation
procedures.)
2. Remove the fuel tank bolts.
1. Screw
3. Lift the front of the fuel tank up-
ward and position it away from the
air filter. (Do not remove the fuel
tank.)
EW000071
lSupport the fuel tank carefully
during this procedure.
lDo not tilt the fuel tank too
much or pull it too hard be-
cause the fuel hose connec-
tions may become loose
causing fuel leakage.
4. Remove the air filter case cover
screw.
R
8-2
SPECIFICATIONS
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-8.frame
Final gear oil
Type SAE 80 API ÒGL-4Ó hypoid gear
oil
Quantity 0.19 L
Air filterDry type element
Fuel
Ty p eRegular unleaded gasoline
Fuel tank capacity 13.5 L
Reserve amount 2.5 L
Carburetor
Type ´ quantity BDS34 ´ 2
Manufacturer MIKUNI
Spark plug
Type/Manufacturer Except for CH:
BPR6ES / NGK or
W20EPR-U / DENSO
For CH:
BPR7ES / NGK or
W22EPR-U / DENSO
Gap 0.7 ~ 0.8 mm
Clutch typeWet, multiple-disc
Transmission
Primary reduction system Spur gear
Primary reduction ratio 1.944
Secondary reduction system Shaft drive
Secondary reduction ratio 3.071
Transmission type Constant mesh 5-speed
Operation Left foot operation
Gear ratio
1st 2.714
2nd 1.900
3rd 1.458
4th 1.167
5th 0.967
Chassis
Frame type Pressed backbone
Caster angle 31.5û
Tr a i l 1 2 5 m m
Tires
Front
Type With tube
Size 3.00-19 49S
Manufacturer/
model Bridgestone / L303A
Dunlop / F14G
Rear
Type With tube
Size 140/90-15M/C 70S
Manufacturer/
model Bridgestone / G508
Dunlop / K425
L
8-3
SPECIFICATIONS
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-8.frame
Maximum load* 220 kg (except for CH, A)
218 kg (for CH, A)
Air pressure (cold tire)
Up to 90 kg load*
Front 200 kPa (2.00 kg/cm
2, 2.00 bar)
Rear 225 kPa (2.25 kg/cm
2, 2.25 bar)
90 kg load ~ maximum
load*
Front 200 kPa (2.00 kg/cm
2, 2.00 bar)
Rear 250 kPa (2.50 kg/cm
2, 2.50 bar)
* Load is total weight of cargo, rider, passenger and accessories.
Wheels
Front
Type Spoke
Size 19 ´ MT1.85
Rear
Type Spoke
Size 15M/C ´ MT3.00
Brakes
Front
Type Single disc brake
Operation Right hand operation
Fluid DOT 4 or DOT 3
Rear
Type Drum brake
Operation Right foot operation
Suspension
Front
Type Telescopic fork
Rear
Type Swingarm
Shock absorbers
Front Coil spring/oil damper
Rear Coil spring/oil damper
Wheel travel
Front 150 mm
Rear 85 mm
Electrical system
Ignition system T.C.I. (digital)
Charging system
Type A.C. magneto
Standard output 14 V, 24 A @ 5,000 r/min
Battery
Type GM12AZ-3A-2
Voltage, capacity 12 V, 12 AH
Headlight typeQuartz bulb (halogen)
