2000 YAMAHA XV125S light

1
2
3
4
5
6
7
8
9
6-34
PERIODIC MAINTENANCE AND MINOR REPAIR
3. Turn the bulb holder counter-
clockwise to remove it and
remove the defective bulb.
EW000119
w
Keep flammable products and your
hands away from a bulb while it is
on, as it is hot. Do not touch a bulb
until it cools down.
4. Put a new bulb into position
and secure it in place with the
bulb holder.
1. Bulb holder
EC000105
cC
Avoid touching the glass part of a
bulb. Keep it free from oil; other-
wise, the transparency of the
glass, life of the bulb, and lumi-
nous flux will be adversely affect-
ed. If oil gets on a bulb, thoroughly
clean it with a cloth moistened
with alcohol or lacquer thinner.
5. Install the bulb cover, connec-
tors and headlight unit.
Ask a Yamaha dealer to adjust
the headlight beam if neces-
sary.
1. Don’t touch
1
1
1
EAU03010Turn signal light bulb
replacement
1. Remove the screws and the
lens.
1. Screw (´2)
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 65

6-35
1
2
3
4
5
6
7
8
9
1
2. Remove the defective bulb by
pushing it inward and turning
it counterclockwise.
3. Install a new bulb by pushing
it inward and turning it clock-
wise.
4. Install the lense and tighten
the screws.
EC000108
cC
Do not over-tighten the screws as
the lens may break.
1. Bulb
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2. Remove the defective bulb by
pushing it inward and turning
it counterclockwise.
3. Install a new bulb by pushing
it inward and turning it clock-
wise.
4. Install the lens and tighten the
screws.
1. Bulb
1
EAU01623Taillight bulb replacement
1. Remove the screws and the
lense.
1. Screw (´2)
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 66

6-39
1
2
3
4
5
6
7
8
97. Adjust the rear brake pedal
height and free play. (See page
6-21.)
EW000103
w
Check the operation of the brake
light after adjusting the rear brake.
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU01696Rear wheel installation
1. Install the rear wheel and the
axle.
2. Install the axle nut and let the
motorcycle down.
3. Insert the brake rod into the
brake cam lever and install the
brake pedal free play adjusting
nut.
4. Install the brake torque rod
bolt and tighten to the speci-
fied tightening torque. Then
install a new cotter pin.
5. Adjust the drive chain free
play. (See page 6-25.)
6. Tighten the axle nut to the
specified tightening torque. Specified torque:
Brake torque rod bolt:
23 Nm (2.3 m·kg)
Specified torque:
Axle nut:
105 Nm (10.5 m·kg)
435
12
5. Remove the rear brake pedal
free play adjusting nut and
brake rod from the brake cam
lever.
6. Loosen the locknuts and chain
adjusting nuts on each side.
7. Remove the axle nut.
8. Pull out the wheel axle and
remove the wheel assembly.
1. Cotter pin
2. Alignment marks
3. Locknut
4. Chain adjusting nut
5. Axle nut
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 70

1
2
3
4
5
6
7
8
9
MOTORCYCLE CARE AND STORAGE
7-2
8Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent
and water to clean plastic.
8Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, solvent
or thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.8Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel bearings, swingarm
bearings, forks and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
8For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure they
do not leave any marks. If the
windshield is scratched, use a
quality plastic polishing com-
pound after washing.After riding in the rain, near the
sea or on salt-sprayed roads
Since sea salt or salt sprayed on
the roads in the winter are
extremely corrosive in combina-
tion with water, carry out the fol-
lowing steps after each ride in the
rain, near the sea or on salt-
sprayed roads. (Salt sprayed in the
winter may remain on the roads
well into spring.)
1. Clean your motorcycle with
cold water and soap after the
engine has cooled down.
ECA00012
cC
Do not use warm water since it
increases the corrosive action of
the salt.
2. Be sure to apply a corrosion
protection spray on all (even
chrome- and nickel-plated)
metal surfaces to prevent cor-
rosion.
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 74

SPECIFICATIONS
1
2
3
4
5
6
7
8
9
Maximum load* 183 kg
Air pressure (cold tire)
up to 90 kg load*
Front
175 kPa (1.75 kg/cm2, 1.75 bar)
Rear200 kPa (2.00 kg/cm2, 2.00 bar)
90 kg load ~ Maximum
load*
Front
200 kPa (2.00 kg/cm2, 2.00 bar)
Rear225 kPa (2.25 kg/cm2, 2.25 bar)
*Load is total weight of cargo, rider, passenger and accessories.
Wheels
Front
Type Spoke wheel
Size 18 ´1.6
Rear
Type Spoke wheel
Size 15 M/C ´MT 2.75
Brakes
Front
Type Single disc brake
Operation Right hand operation
Fluid DOT 4 or DOT 3Rear
Type Drum brake
Operation Right foot operation
Suspension
Front
Type Telescopic fork
Rear
Type Swingarm
Shock absorbers
Front Coil spring/oil damper
Rear Coil spring/oil damper
Wheel travel
Front 140 mm
Rear 100 mm
Electrical system
Ignition system T.C.I. (Digital)
Charging system
Type A.C. magneto
Standard output 14 V, 22 A @ 5,000 rpm
Battery
Type GM10-3A-2
Voltage, capacity 12 V, 10 AH
Headlight typeQuartz bulb (Halogen)
8-3
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 80

SPECIFICATIONS
1
2
3
4
5
6
7
8
9
Bulb voltage, wattage ´quantity
Headlight 12 V, 60 W/55 W ´1
Tail/brake light 12 V, 5 W/21 W ´1
Flasher light 12 V, 21 W ´4
Auxiliary light 12 V, 4 W ´1 (except for GB)
12 V , 3.4 W ´1 (for GB)
Meter light 12 V, 1.7 W ´1
Neutral indicator light 12 V, 1.7 W ´1
High beam indicator light 12 V, 1.7 W ´1
Turn indicator light 12 V, 3 W ´1
Fuse
Main 20 A
Signaling system 10 A
8-4
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 81