6-12
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9 8.Fill the engine with oil. Install the
oil tank cap. Tightening torque:
Drain plug (crankcase):
30 Nm (3.0 m0kg)
Drain plug (oil tank):
17.5 Nm (1.75 m0kg)
Filter cover bolt:
10 Nm (1.0 m0kg)
Air bleed screw:
5 Nm (0.5 m0kg)
Recommended oil:
See page 8-1
Oil quantity:
Total amount:
3.3 L
Periodic oil change:
2.7 L
With oil filter replacement:
2.8 L
9.Start the engine and warm it up
for a few minutes. While warming
up, check for oil leakage. If oil
leakage is found, stop the engine
immediately and check for the
cause.
10.Stop the engine and check the
oil level.
EC000076
cCAfter replacing the engine oil, be
sure to check the oil pressure as
described below.8 8
Remove the air bleed screw
from the oil filter cover.
8 8
Start the engine and keep it
idling until oil flows out of the
bleed hole. If no oil comes out
after one minute, turn off the
engine immediately so it will
not seize. In such a case go to
the nearest Yamaha dealer for
repairs.
8 8
After checking, tighten the air
bleed screw securely.
1
1
EAU01083
Air filterThe air filter should be cleaned at the
specified intervals. It should be
cleaned more frequently if you are
riding in unusually wet or dusty
areas.
1.Remove panel B. (See page 6-7
for panel removal and installation
procedures.)
2.Remove the air filter case fitting
screws and the filter case cover.1.Screw (´7)
4PT-9-E6 (ENG) 6 12/27/00 1:29 PM Page 13
6-24
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
EC000097
cCBe sure to oil the chain after wash-
ing the motorcycle or riding in the
rain.
EAU00773
Throttle cable and grip
lubricationThe throttle twist grip assembly
should be greased at the time that
the cable is lubricated, since the grip
must be removed to get at the end of
the throttle cable. After removing the
screws, hold the end of the cable up
in the air and put in several drops of
lubricant. With the throttle grip disas-
sembled, coat the metal surface of
the grip assembly with a suitable all-
purpose grease.
EAU02962
Cable inspection and
lubrication
EW000112
wDamage to the outer housing of
cables may lead to internal rusting
and interfere with the cable move-
ment. Replace damaged cables as
soon as possible to prevent unsafe
conditions.Lubricate the cables and cable ends.
If a cable does not operate smoothly,
ask a Yamaha dealer to replace it.
Recommended lubricant:
Engine oil
4PT-9-E6 (ENG) 6 12/27/00 1:29 PM Page 25
6-25
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
EAU02984
Brake and shift pedal
lubricationLubricate the pivoting parts.
Recommended lubricant:
Engine oil
EAU02986
Sidestand lubricationLubricate the sidestand pivoting point
and metal-to-metal contact surfaces.
Check that the sidestand moves up
and down smoothly.
EW000113
wIf the sidestand does not move
smoothly, consult a Yamaha deal-
er.
Recommended lubricant:
Engine oil
EAU02985
Brake and clutch lever
lubricationLubricate the pivoting parts.
Recommended lubricant:
Engine oil
4PT-9-E6 (ENG) 6 12/27/00 1:29 PM Page 26
6-26
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
EAU00790
Rear suspension lubricationLubricate the pivoting parts.
Recommended lubricant:
Molybdenum disulfide grease
1
1
1.Grease nipple (´2)
Operation check
1.Place the motorcycle on a level
place.
2.Hold the motorcycle in an upright
position and apply the front
brake.
3.Push down hard on the handle-
bars several times and check if
the fork rebounds smoothly.
EC000098
cCIf any damage or unsmooth move-
ment is found with the front fork,
consult a Yamaha dealer.
EAU02939
Front fork inspectionVisual check
EW000115
wSecurely support the motorcycle
so there is no danger of it falling
over.Check for scratches or damage on
the inner tube and excessive oil leak-
age from the front fork.
4PT-9-E6 (ENG) 6 12/27/00 1:29 PM Page 27
7-1
CareThe exposure of its technology
makes a motorcycle charming but
also vulnerable. Although high-quality
components are used, they are not
all rust-resistant. While a rusty
exhaust pipe may remain unnoticed
on a car, it does look unattractive on
a motorcycle. Frequent and proper
care, however, will keep your motor-
cycle looking good, extend its life and
maintain its performance. Moreover,
the warranty states that the vehicle
must be properly taken care of. For
all these reasons, it is recommended
that you observe the following clean-
ing and storing precautions.Before cleaning
1.Cover up the muffler outlet with a
plastic bag.
2.Make sure that all caps and cov-
ers as well as all electrical cou-
plers and connectors, including
the spark plug cap, are tightly
installed.
3.Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
tooth or bottle brush, but never
apply such products onto seals,
gaskets, sprockets, the drive
chain and wheel axles. Always
rinse the dirt and degreaser off
with water.Cleaning
After normal use
Remove dirt with warm water, a neu-
tral detergent and a soft clean
sponge, then rinse with plenty of
clean water. Use a brush for hard-to-
reach parts. Tougher dirt and insects
will come off more easily if the area is
covered with a wet cloth for a few
minutes before cleaning.
ECA00010
cC8 8
Avoid using strong acidic
wheel cleaners, especially on
spoked wheels. If you do use
such products for hard-to-
remove dirt, do not leave it on
any longer than instructed,
then thoroughly rinse it off
with water, immediately dry
the area and apply a corrosion
protection spray.
EAU01518
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
67
8
94PT-9-E6 (ENG) 7~9 12/27/00 1:30 PM Page 2
SPECIFICATIONS
1
2
3
4
5
6
78
9
Specifications
ModelXT500E/XT600E
Dimensions
Overall length2,220 mm
2.295 mm (N, S, CH only)
Overall width865 mm
825 mm (CH only)
Overall height1,205 mm
Seat height855 mm
Wheel base1,440 mm
Minimum ground clearance230 mm
Minimum turning radius2,300 mm
Basic weight (with oil and full
fuel tank)176 kg
172 kg (CH only)
Engine
Engine typeAir-cooled 4-stroke, SOHC,
gasoline
Cylinder arrangementForward inclined single
cylinder
Displacement499 cm
3
595 cm
3
Bore
´Stroke87.0 ´84.0 mm (XT500E)
95.0 ´84.0 mm (XT600E)
Compression ratio8.5:1
Starting systemElectric starter
Lubrication systemDry sumpEngine oil
Type
Recommended engine oil
classificationAPI Service SE, SF, SG type
or higher
cCBe sure to use motor oils that do not contain anti-friction
modifiers. Passenger car motor oils (often labeled
ÒEnergy ConservingÓ) contain anti-friction additives which
will cause clutch and/or starter clutch slippage, resulting in
reduced component life and poor engine performance.
Capacity
Periodic oil change2.7 L
With oil filter replacement2.8 L
Total amount3.3 L
EAU01038
SPECIFICATIONS
8-1
–10° 0° 10° 20° 30°
40°
SAE 10W/30
SAE 10W/40
SAE 20W/40
SAE 20W/50
–20°
SAE 15W/40 50°C
4PT-9-E6 (ENG) 7~9 12/27/00 1:30 PM Page 8
INDEX
Front brake lever free play
adjustment..........................................6-18
Front fork inspection..............................6-26
Front wheel installation..........................6-34
Front wheel removal..............................6-33
Fuel.........................................................3-6
Fuel cock.................................................3-7
Fuel tank cap...........................................3-6
Fuse replacement..................................6-29
H
Handlebar switches.................................3-3
Dimmer switch......................................3-3
Engine stop switch................................3-4
Horn switch...........................................3-3
Lights switch.........................................3-3
Pass switch...........................................3-3
Start switch...........................................3-4
Turn signal switch.................................3-3
Headlight bulb replacement...................6-29
Helmet holder..........................................3-9
High beam indicator light.........................3-2
Horn switch..............................................3-3
How to use the conversion table.............9-3
I
Identification number records..................9-1
Idle speed adjustment...........................6-14
Indicator lights.........................................3-2
High beam indicator light......................3-2
Neutral indicator light............................3-2
Turn indicator light................................3-2
Inspecting the brake fluid level..............6-21
K
Key identification number........................9-1
L
Lights switch............................................3-3
M
Main switch/Steering lock........................3-1
Model label..............................................9-2
N
Neutral indicator light...............................3-2
P
Panel A, B...............................................6-7
Parking....................................................5-6
Pass switch.............................................3-3
Periodic maintenance and
lubrication chart....................................6-3
Pre-operation check list...........................4-1
R
Rear brake pedal.....................................3-5
Rear brake pedal height adjustment.....6-19
Rear shock absorber adjustment..........3-10
Rear suspension lubrication..................6-26
Rear wheel installation..........................6-36
Rear wheel removal..............................6-35
Recommended shift point
(for Switzerland only)............................5-4
S
Seat.........................................................3-9
Shift pedal ..............................................3-5
Shifting....................................................5-4
Sidestand..............................................3-11
Sidestand lubrication.............................6-25
A
Air filter..................................................6-12
B
Battery...................................................6-28
Brake and clutch lever lubrication.........6-25
Brake and shift pedal lubrication...........6-25
Brake fluid replacement.........................6-22
Brake light switch adjustment................6-20
C
Cable inspection and lubrication...........6-24
Carburetor adjustment...........................6-13
Care.........................................................7-1
Carrier (optional)...................................3-11
Checking the front and rear brake
pads....................................................6-20
Clutch lever.............................................3-4
Clutch lever free play adjustment..........6-18
Cowling A................................................6-7
Cowling and panel removal and
installation.............................................6-6
D
Description..............................................2-1
Dimmer switch.........................................3-3
Drive chain lubrication...........................6-23
Drive chain slack adjustment.................6-23
Drive chain slack check.........................6-22
E
Engine break-in.......................................5-5
Engine oil...............................................6-10
Engine stop switch..................................3-4
F
Front brake lever.....................................3-5
4PT-9-E6 (ENG) 7~9 12/27/00 1:30 PM Page 16