6-15
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
* Load is the total weight of cargo, rider, passenger
and accessories.Maximum load*176 kg (XT500E)
180 kg (XT600E)
Cold tire pressure:FrontRear
150 kPa150 kPa
Up to 90 kg(1.5 kg/cm
2, (1.5 kg/cm
2,
1.5 bar)1.5 bar)
90 kg load ~150 kPa225 kPa
Maximum load*(1.5 kg/cm
2, (2.25 kg/cm
2,
1.5 bar) 2.25 bar)
125 kPa125 kPa
Off-road riding(1.25 kg/cm
2, (1.25 kg/cm
2,
1.25 bar) 1.25 bar)
150 kPa150 kPa
High speed riding(1.5 kg/cm
2, (1.5 kg/cm
2,
1.5 bar) 1.5 bar)
EAU00652
TiresTo ensure maximum performance,
long service and safe operation, note
the following:
Tire air pressure
Always check and adjust the tire
pressure before operating the motor-
cycle.
EW000082
wTire inflation pressure should be
checked and adjusted when the
temperature of the tire equals the
ambient air temperature. Tire infla-
tion pressure must be adjusted
according to total weight of cargo,
rider, passenger, and accessories
(fairing, saddlebags, etc. if
approved for this model), and vehi-
cle speed.
EAU00637
Valve clearance adjustmentThe correct valve clearance changes
with use, resulting in improper fuel/air
supply or engine noise. To prevent
this, the valve clearance must be
adjusted regularly. This adjustment
however, should be left to a profes-
sional Yamaha service technician.
4PT-9-E6 (ENG) 6 12/27/00 1:29 PM Page 16
7-2
8 8
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent
and water to clean plastic.
8 8
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or elec-
trolyte.8 8
Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel bearings, swingarm
bearings, forks and brakes),
electric components (cou-
plers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
8 8
For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure they
do not leave any marks. If the
windshield is scratched, use a
quality plastic polishing com-
pound after washing.
After riding in the rain, near the seaor on salt-sprayed roads.Since sea salt or salt sprayed on the
roads in the winter are extremely cor-
rosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads. (Salt sprayed
in the winter may remain on the roads
well into spring.)
1.Clean your motorcycle with cold
water and soap after the engine
has cooled down.
ECA00012
cCDo not use warm water since it
increases the corrosive action of
the salt.2.Be sure to apply a corrosion pro-
tection spray on all (even
chrome- and nickel-plated) metal
surfaces to prevent corrosion.
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
67
8
9
4PT-9-E6 (ENG) 7~9 12/27/00 1:30 PM Page 3
