Page 48 of 101
R
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-6TOC.-
Tool kit ................................................................ 6-1
Periodic maintenance and lubrication................. 6-2
Panel removal and installation ........................... 6-5
Panel A ............................................................... 6-5
Spark plug inspection ......................................... 6-6
Engine oil............................................................ 6-7
Air filter ............................................................. 6-10
Carburetor adjustment ...................................... 6-11
Idle speed adjustment ...................................... 6-12
Throttle cable free play inspection .................... 6-12
Valve clearance adjustment ............................. 6-13
Tires ................................................................. 6-13
Wheels ............................................................. 6-15
Clutch lever free play adjustment ..................... 6-15
Rear brake pedal height adjustment ................ 6-17
Brake light switch adjustment ........................... 6-17
Checking the front and rear brake pads ........... 6-18
Inspecting the brake fluid level ......................... 6-19
Brake fluid replacement .................................... 6-20
Drive chain slack check .................................... 6-20
Drive chain slack adjustment ............................ 6-21Drive chain lubrication....................................... 6-21
Cable inspection and lubrication ....................... 6-22
Throttle cable and grip lubrication ..................... 6-22
Brake and shift pedal lubrication ....................... 6-22
Brake and clutch lever lubrication ..................... 6-23
Center and sidestand lubrication ...................... 6-23
Rear suspension lubrication.............................. 6-23
Front fork inspection ......................................... 6-24
Steering inspection ........................................... 6-24
Wheel bearings ................................................. 6-25
Battery............................................................... 6-25
Fuse replacement ............................................. 6-26
Headlight bulb replacement (for XJ600S) ......... 6-27
Headlight bulb replacement (for XJ600N) ......... 6-29
Front wheel removal ......................................... 6-31
Front wheel installation ..................................... 6-31
Rear wheel removal .......................................... 6-33
Rear wheel installation ...................................... 6-34
Troubleshooting ................................................ 6-34
Troubleshooting chart ....................................... 6-35
Page 50 of 101
R
6-2
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-6.frame
EAU00473
PERIODIC MAINTENANCE AND LUBRICATION
NO. ITEM CHECKS AND MAINTENANCE JOBSINITIAL
(1,000 km)EVERY
6,000 km
or
6 months
(whichever
comes first)12,000 km
or
12 months
(whichever
comes first)
1
*Fuel line ¥ Check fuel hoses and vacuum hose for cracks or damage.
¥ Replace if necessary.ÖÖ
2
*Fuel filter¥ Check condition.
¥ Replace if necessary.Ö
3 Spark plugs¥ Check condition.
¥ Clean, regap or replace if necessary.ÖÖÖ
4
*Valves¥ Check valve clearance.
¥ Adjust if necessary.Every 24,000 km or 24 months
(whichever comes first)
5 Air filter¥ Clean or replace if necessary.ÖÖ
6Clutch¥ Check operation.
¥ Adjust or replace cable.ÖÖÖ
7
*Front brake¥ Check operation, fluid level and vehicle for fluid leakage. (See NOTE
on page 6-4.)
¥ Correct accordingly.
¥ Replace brake pads if necessary.ÖÖÖ
8
*Rear brake¥ Check operation, fluid level and vehicle for fluid leakage. (See NOTE
on page 6-4.)
¥ Correct accordingly.
¥ Replace brake pads if necessary.ÖÖÖ
9
*Wheels¥ Check balance, runout and for damage.
¥ Rebalance or replace if necessary.ÖÖ
10
*Tires¥ Check tread depth and for damage.
¥ Replace if necessary.
¥ Check air pressure.
¥ Correct if necessary.ÖÖ
Page 52 of 101
R
6-4
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-6.frame
* Since these items require special tools, data and technical skills, they should be serviced by a Yamaha dealer.
EAU01792
NOTE:
lThe air filter needs more frequent service if you are riding in unusually wet or dusty areas.
lHydraulic brake system
¥ When disassembling the master cylinder or caliper, always replace the brake fluid. Check the brake fluid level regularly
and fill as required.
¥ Replace the oil seals on the inner parts of the master cylinder and caliper cylinder every two years.
¥ Replace the brake hoses every four years or if cracked or damaged.
21*Carburetors¥ Check engine idling speed, synchronization and starter operation.
¥ Adjust if necessary.ÖÖÖ
22 Engine oil¥ Check oil level and vehicle for oil leakage.
¥ Correct if necessary.
¥ Change. (Warm engine before draining.)ÖÖÖ
23 Engine oil filter cartridge¥ Replace.ÖÖ NO. ITEM CHECKS AND MAINTENANCE JOBSINITIAL
(1,000 km)EVERY
6,000 km
or
6 months
(whichever
comes first)12,000 km
or
12 months
(whichever
comes first)
Page 63 of 101
L
6-15
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-6.frame
EAU00683
Operating the motorcycle with ex-
cessively worn tires decrease riding
stability and can lead to loss of con-
trol. Have excessively worn tires re-
placed by a Yamaha dealer
immediately. Brakes, tires, and re-
lated wheel parts replacement
should be left to a Yamaha Service
Technician.
EAU00687
Wheels
To ensure maximum performance,
long service, and safe operation, note
the following:
lAlways inspect the wheels before
a ride. Check for cracks, bends, or
warpage of the wheels. If any ab-
normal condition exists in a wheel,
consult a Yamaha dealer. Do not
attempt even small repairs to the
wheel. If a wheel is deformed or
cracked, it must be replaced.
lTires and wheels should be bal-
anced whenever either one is
changed or replaced. Failure to
have a wheel balanced can result
in poor performance, adverse han-
dling characteristics, and short-
ened tire life.
lRide at moderate speeds after
changing a tire since the tire sur-
face must first be broken in for it to
develop its optimal characteristics.
1. Locknut
2. Adjusting bolt
c. Free play
EAU00694
Clutch lever free play
adjustment
The clutch lever free play should be ad-
justed to 2 ~ 3 mm.
1. Loosen the locknut at the clutch le-
ver.
2. Turn the adjusting bolt at the
clutch lever in direction a
to in-
crease free play or in direction b
to decrease free play.
3. Tighten the locknut at the clutch
lever.
Page 65 of 101
L
6-17
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-6.frame
a. Pedal height
EAU00712
Rear brake pedal height
adjustment
The top of the brake pedal should be
positioned 40 mm below the top of the
footrest. If not, ask a Yamaha dealer to
adjust it.
EW000109
A soft or spongy feeling in the brake
pedal can indicate the presence of
air in the brake system. This air
must be removed by bleeding the
brake system before the motorcycle
is operated. Air in the system will
cause greatly diminished braking
capability and can result in loss of
control and an accident. Have a
Yamaha dealer inspect and bleed
the system if necessary.
1. Brake light switch
2. Adjusting nut
EAU00713
Brake light switch adjustment
The rear brake light switch is activated
by the brake pedal and is properly ad-
justed when the brake light comes on
just before braking takes effect. To ad-
just the rear brake light switch, hold the
switch body so it does not rotate while
turning the adjusting nut. Turn the ad-
justing nut in direction a
to make the
brake light come on earlier. Turn the
adjusting nut in direction b
to make the
brake light come on later.
Page 66 of 101
R
6-18
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-6.frame
1. Wear indicator groove (´ 2)
EAU00721
Checking the front and rear
brake pads
EAU00725
Front brake
A wear indicator groove is provided on
each brake pad. This indicator allows
checking of brake pad wear without
disassembling the brake. Inspect the
groove. If the groove has almost disap-
peared, ask a Yamaha dealer to re-
place the pads.
1. Wear indicator (´ 2)
EAU00728
Rear brake
Apply the brake and inspect the wear
indicator. If the wear indicator is
ALMOST in contact with the disc plate,
ask a Yamaha dealer to replace the
pads.
Page 67 of 101
L
6-19
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-6.frame
1. Minimum level mark
EAU00732
Inspecting the brake fluid
level
Insufficient brake fluid may let air enter
the brake system, possibly causing the
brakes to become ineffective.
Before riding, check that the brake fluid
is above the minimum level and fill
when necessary.
Observe these precautions:
lWhen checking the fluid level,
make sure the top of the master
cylinder is level by turning the han-
dlebars.
1. Minimum level mark
l
Use only the designated quality
brake fluid. Otherwise, the rubber
seals may deteriorate, causing
leakage and poor brake perfor-
mance.
NOTE:
If DOT 4 is not available, DOT 3 can be
used.Recommended brake fluid: DOT 4
lRefill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor brake performance.
lBe careful that water does not en-
ter the master cylinder when refill-
ing. Water will significantly lower
the boiling point of the fluid and
may result in vapor lock.
lBrake fluid may deteriorate paint-
ed surfaces or plastic parts. Al-
ways clean up spilled fluid
immediately.
lHave a Yamaha dealer check the
cause if the brake fluid level goes
down.
Page 68 of 101
R
6-20
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-6.frame
EAU00742
Brake fluid replacement
The brake fluid should be replaced only
by trained Yamaha service personnel.
Have the Yamaha dealer replace the
following components during periodic
maintenance or when they are dam-
aged or leaking:
loil seals (every two years)
lbrake hoses (every four years)a. Chain slack
EAU00745
Drive chain slack check
NOTE:
Spin the wheel several times and find
the tightest position of the chain. Check
and/or adjust the chain slack while itÕs
in this tightest position.
Inspect the drive chain when the motor-
cycle is on the centerstand. Check the
slack at the position shown in the illus-
tration. Normal slack is approximately
30 ~ 40 mm. If the slack exceeds
40 mm, adjust.
