2000 YAMAHA TW125 fuel

7-2
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
6
7
8
9 8Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent
and water to clean plastic.
8Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, solvent
or thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.8Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel bearings, swingarm
bearings, forks and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
8For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure they
do not leave any marks. If the
windshield is scratched, use a
quality plastic polishing com-
pound after washing.
After riding in the rain, near the
sea or on salt-sprayed roads
Since sea salt or salt sprayed on
the roads in the winter are
extremely corrosive in combina-
tion with water, carry out the fol-
lowing steps after each ride in the
rain, near the sea or on salt-
sprayed roads. (Salt sprayed in the
winter may remain on the roads
well into spring.)
1. Clean your motorcycle with
cold water and soap after the
engine has cooled down.
ECA00012
cC
Do not use warm water since it
increases the corrosive action of
the salt.
2. Be sure to apply a corrosion
protection spray on all (even
chrome- and nickel-plated)
metal surfaces to prevent cor-
rosion.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 71

7-4
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
6
7
8
9
Storage
Short-term
Always store your motorcycle in a
cool, dry place and, if necessary,
protect it against dust with a
porous cover.
ECA00014
cC
8Storing the motorcycle in a
poorly ventilated room or cov-
ering it with a tarp while it is
still wet will allow water and
humidity to seep in and cause
rust.
8To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chem-
icals are stored.
Long-term
Before storing your motorcycle for
several months:
1. Follow all the instructions in
the “Care” section of this
chapter.
2. Drain the carburetor float
chamber by loosening the
drain bolt; this will prevent fuel
deposits from building up.
Pour the drained fuel into the
fuel tank.
3. Only for motorcycles equipped
with a fuel cock which has an
“OFF” position: Turn the fuel
cock to “OFF”.
4. Fill up the fuel tank and add
fuel stabilizer (if available) to
prevent the fuel tank from rust-
ing and the fuel from deterio-
rating.
5. Perform the following steps to
protect the cylinder, piston
rings, etc. from corrosion.
a. Remove the spark plug cap
and spark plug.b. Pour a teaspoonful of engine
oil into the spark plug bore.
c. Install the spark plug cap onto
the spark plug and place the
spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit
sparking during the next step.)
d. Turn the engine over several
times with the starter. (This
will coat the cylinder wall with
oil.)
e. Remove the spark plug cap
from the spark plug, install the
spark plug and then the spark
plug cap.
EWA00003
w
When turning the engine over, be
sure to ground the spark plug elec-
trodes to prevent damage or injury
from sparking.
6. Lubricate all control cables and
the pivoting points of all levers
and pedals as well as of the
sidestand/centerstand.
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 73

8-1
EAU01038
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
Specifications
Model TW125
Dimensions
Overall length 2,140 mm
Overall width 810 mm
Overall height 1,120 mm
Seat height 805 mm
Wheelbase 1,330 mm
Ground clearance 260 mm
Minimum turning radius 2,100 mm
Basic weight (with oil and full
fuel tank)125 kg
Engine
Engine type Air-cooled 4-stroke, SOHC
Cylinder arrangement Forward inclined
single cylinder
Displacement 124 cm
3
Bore ´Stroke 57.0 ´48.8 mm
Compression ratio 10:1
Starting system Electric starter
Lubrication system Wet sumpEngine oil
Type
Recommended engine oil
classification API Service SE, SF, SG type
or higher
cC
Be sure to use motor oils that do not contain anti-friction
modifiers. Passenger car motor oils (often labeled “Energy
Conserving”) contain anti-friction additives which will cause
clutch and/or starter clutch slippage, resulting in reduced
component life and poor engine performance.
Capacity
Periodic oil change 1.0 L
With oil filter replacement 1.1 L
Total amount 1.3 L
Air filterWet type element
–10° 0° 10° 20° 30°
40°
SAE 10W/30
SAE 10W/40
SAE 20W/40
SAE 20W/50
–20°
SAE 15W/40 50°C
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 75

Fuel
Type Regular unleaded gasoline
Fuel tank capacity 7.0 L
Reserve amount 1.0 L
Carburetor
Type/quantity Y24P/1
Manufacturer TEIKEI
Spark plug
Manufacturer / Type NGK / DR8EA
Spark plug gap 0.6 ~ 0.7 mm
Clutch typeWet, multiple-disc
Transmission
Primary reduction system Spur gear
Primary reduction ratio 74/20 (3.700)
Secondary reduction system Chain drive
Secondary reduction ratio 50/14 (3.571)
Transmission type Constant mesh 5-speed
Operation Left foot operationGear ratio 1st 2.250
2nd 1.476
3rd 1.125
4th 0.926
5th 0.793
Chassis
Frame type Diamond
Frame type Pressed and steel tube frame
Caster angle 26°
Trail 95 mm
Tires
Type With tube
Front
Size 130/80-18 66P
Manufacturer/ BRIDGESTONE / TW31
model
Rear
Size 180/80-14M/C 78P
Manufacturer/ BRIDGESTONE / TW34
model
Maximum load* 180 kg
Air pressure (cold tire)
up to 80 kg load*
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
8-2
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 76