SPEC
2 - 1
GENERAL SPECIFICATIONS
EC200000
SPECIFICATIONS
EC211000
GENERAL SPECIFICATIONS
Model name: TT-R125M
(USA-except for California, CDN, AUS, NZ)
TT-R125MC (USA for California)
TT-R125 (EUROPE)
Model code number: 5HP1 (USA-except for California)
5HP2 (USA for California, AUS, NZ, EUROPE)
5HP3 (CDN)
Dimensions: USA, AUS, NZ,
EUROPECDN
Overall length 1,830 mm (72.0 in) 1,865 mm (73.4 in)
Overall width 785 mm (30.9 in)
¬
Overall height 1,055 mm (41.5 in)
¬
Seat height 775 mm (30.5 in)
¬
Wheelbase 1,250 mm (49.2 in)
¬
Minimum ground clearance 265 mm (10.4 in)
¬
Basic weight:
With oil and full fuel tank 83 kg (183 lb)
Engine:
Engine type Air cooled 4-stroke, SOHC
Cylinder arrangement Single cylinder, forward inclined
Displacement 123.7 cm
3
(7.55 cu.in)
Bore
´
stroke 54.0
´
54.0 mm (2.126
´
2.126 in)
Compression ratio 10.0:1
Starting system Kickstarter
Lubrication system: Wet sump
Oil type or grade:
Engine oil (For USA and CDN)
At –10 ˚C (10 ˚F) or higher
Yamalube 4 (10W-30) or SAE 10W-30 type
SE motor oil
At 5 ˚C (40 ˚F) or higher
õ
Yamalube 4 (20W-40) or SAE 20W-40 type
SE motor oil
(Except for USA and CDN)
API “SE” or higher grade
2
SPEC
2 - 13
MAINTENANCE SPECIFICATIONS
Brake lever and brake pedal:
Brake lever free play (lever end) 10 ~ 15 mm (0.39 ~ 0.59 in) ----
Brake pedal position
(vertical height below footrest top)1 mm (0.04 in) ----
Brake pedal free play 20 ~ 30 mm (0.79 ~ 1.18 in) ----
Clutch lever free play (lever end) 10 ~15 mm (0.39 ~ 0.59 in) ----
Throttle grip free play 3 ~ 5 mm (0.12 ~ 0.20 in) ----Item Standard Limit
3 - 16
INSP
ADJBRAKE PEDAL HEIGHT ADJUSTMENT/BRAKE SHOE
INSPECTION/SPROCKETS INSPECTION
BRAKE PEDAL HEIGHT ADJUSTMENT
1. Check:
lBrake pedal height a
Out of specification ® Adjust.
Brake pedal height a:
1 mm (0.04 in)
2. Adjust:
lBrake pedal height
Pedal height adjustment steps:
lLoosen the locknut 1.
lTurn the adjusting bolt 2 until the pedal
height a is within specified height.
lTighten the locknut.
BRAKE SHOE INSPECTION
1. Inspect:
lBrake shoe lining wear limit
Front
õRear
Brake shoe lining wear limit checking
steps:
lFully pull in the brake lever (push down
the pedal) and hold it in position.
lThen check the brake shoe wear indicator
1 is within the wear limit a.
Outside the limit ® Replace the brake
shoe.
Refer to “FRONT WHEEL AND FRONT
BRAKE” or “REAR WHEEL AND REAR
BRAKE” section in the CHAPTER 5.
õ
SPROCKETS INSPECTION
1. Inspect:
lSprocket teeth a
Excessive wear ® Replace.
NOTE:
Replace the drive, driven sprockets and drive
chain as a set.
