2000 YAMAHA SR125 key

EAU00005
IMPORTANT MANUAL INFORMATIONParticularly important information is distinguished in this manual by the following notations:
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS
INVOLVED!
WARNING
Failure to follow WARNING instructions could result in severe injury or death
to the
motorcycle operator, a bystander or a person inspecting or repairing the motorcycle.
CAUTION:A CAUTION indicates special precautions that must be taken to avoid damage to the
motorcycle.NOTE:
A NOTE provides key information to make procedures easier or clearer.
NOTE:@ l
This manual should be considered a permanent part of this motorcycle and should remain
with it even if the motorcycle is subsequently sold.
l
Yamaha continually seeks advancements in product design and quality. Therefore, while
this manual contains the most current product information available at the time of printing,
there may be minor discrepancies between your motorcycle and this manual. If there is any
question concerning this manual, please consult your Yamaha dealer.
@
E_3mw.book Page 1 Monday, February 5, 2001 9:54 AM

TABLE OF CONTENTS
Throttle cable free play adjustment .................. 6-12
Cam chain adjustment ..................................... 6-12
Valve clearance adjustment ............................. 6-13
Tires ................................................................. 6-13
Wheels ............................................................. 6-15
Clutch lever free play adjustment..................... 6-16
Front brake lever free play adjustment ............ 6-16
Rear brake pedal height and free play
adjustment .................................................... 6-17
Brake light switch adjustment .......................... 6-18
Checking the front brake pads and
rear brake shoes .......................................... 6-19
Inspecting the brake fluid level......................... 6-20
Brake fluid replacement ................................... 6-20
Drive chain slack check ................................... 6-21
Drive chain slack adjustment ........................... 6-22
Drive chain lubrication...................................... 6-23
Cable inspection and lubrication ...................... 6-23
Throttle cable and grip lubrication .................... 6-23
Brake and shift pedal lubrication ...................... 6-24
Brake and clutch lever lubrication .................... 6-24
Center and sidestand lubrication ..................... 6-24
Front fork inspection ........................................ 6-25
Steering inspection .......................................... 6-26
Wheel bearings ................................................ 6-26
Battery.............................................................. 6-26
Fuse replacement ............................................ 6-28
Headlight bulb replacement ............................. 6-29Turn signal and tail/brake light bulb
replacement.................................................. 6-30
Front wheel removal ........................................ 6-30
Front wheel installation .................................... 6-31
Rear wheel removal ......................................... 6-32
Rear wheel installation ..................................... 6-33
Troubleshooting ............................................... 6-33
Troubleshooting chart ...................................... 6-34
MOTORCYCLE CARE AND STORAGE ............. 7-1
Care ................................................................... 7-1
Storage .............................................................. 7-4
SPECIFICATIONS ............................................... 8-1
Specifications ..................................................... 8-1
How to use the conversion table ........................ 8-5
CONSUMER INFORMATION.............................. 9-1
Identification number records............................. 9-1
Key identification number................................... 9-1
Vehicle identification number ............................. 9-1
Model label......................................................... 9-2
789
E_3mw.book Page 2 Monday, February 5, 2001 9:54 AM

3-1
3
EAU00027
3-INSTRUMENT AND CONTROL FUNCTIONS
EAU00029*
Main switch/steering lockThe main switch controls the ignition
and lighting systems. Its operation is
described below.
EAU00036
ON
Electrical circuits are switched on. The
engine can be started. The key cannot
be removed in this position.
EAU00038
OFF
All electrical circuits are switched off.
The key can be removed in this posi-
tion.
EAU00040
LOCK
The steering is locked in this position
and all electrical circuits are switched
off. The key can be removed in this po-
sition.
To lock the steering, turn the handle-
bars all the way to the left. While push-
ing the key into the main switch, turn it
from “OFF” to “LOCK” and remove it.
To release the lock, turn the key to
“OFF” while pushing.
EW000016
WARNING
@ Never turn the key to “OFF” or
“LOCK” when the motorcycle is
moving. The electrical circuits will
be switched off which may result in
loss of control or an accident. Be
sure the motorcycle is stopped be-
fore turning the key to “OFF” or
“LOCK”. @1. Push
2. Turn
E_3mw.book Page 1 Monday, February 5, 2001 9:54 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-5
3
EAU00162
Rear brake pedalThe rear brake pedal is on the right
side of the motorcycle. Press down on
the brake pedal to apply the rear brake.
EAU00167
Fuel tank capTo open
Insert the key and turn it 1/4 turn clock-
wise. The lock will be released and the
cap can be opened.
To close
Push the tank cap into position with the
key inserted. To remove the key, turn it
counterclockwise to the original posi-
tion.
NOTE:@ This tank cap cannot be closed unless
the key is in the lock. The key cannot
be removed if the cap is not locked
properly. @
EW000023
WARNING
@ Be sure the cap is properly installed
and locked in place before riding the
motorcycle. @
1. Rear brake pedal
1. Open
E_3mw.book Page 5 Monday, February 5, 2001 9:54 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-8
3
EAU01092
SeatTo remove the seat, remove the bolts.To install the seat, insert the projection
on the front of the seat into the holder
and push down on the seat, then tight-
en the bolts.
NOTE:@ Make sure that the seat is securely fit-
ted. @
EAU00261
Helmet holderTo open the helmet holder, insert the
key in the lock and turn it as shown.
To lock the helmet holder, turn the key
to its original position.
EW000030
WARNING
@ Never ride with a helmet in the hel-
met holder. The helmet may hit ob-
jects, causing loss of control and
possibly an accident. @
1. Bolt (´ 2)
1. Seat holder
2. Projection
1. Lock
2. Open
E_3mw.book Page 8 Monday, February 5, 2001 9:54 AM

OPERATION AND IMPORTANT RIDING POINTS
5-6
5
EAU00438
0 ~ 150 km
Avoid operation above 1/3 throttle.
Stop the engine and let it cool for 5 to
10 minutes after every hour of opera-
tion. Vary the speed of the motorcycle
from time to time. Do not operate it at
one set throttle position.
150 ~ 500 km
Avoid prolonged operation above
1/2 throttle.
500 ~ 1,000 km
Avoid cruising speeds in excess of
3/4 throttle.
EC000050
CAUTION:@ After 1,000 km of operation, be sure
to replace the engine oil. @
1,000 km and beyond
Avoid prolonged full-throttle operation.
Vary speed occasionally.
EC000049
CAUTION:@ If any engine trouble should occur
during the break-in period, consult a
Yamaha dealer immediately. @
EAU00457
ParkingWhen parking the motorcycle, stop the
engine and remove the ignition key.
Turn the fuel cock to “OFF” whenever
stopping the engine.
EW000058
WARNING
@ The exhaust system is hot. Park the
motorcycle in a place where pedes-
trians or children are not likely to
touch the motorcycle. Do not park
the motorcycle on a slope or soft
ground; the motorcycle may over-
turn. @
E_3mw.book Page 6 Monday, February 5, 2001 9:54 AM

9-1
9
EAU01039
9-CONSUMER INFORMATION
EAU02944
Identification number recordsRecord the key identification number,
vehicle identification number and mod-
el label information in the spaces pro-
vided for assistance when ordering
spare parts from a Yamaha dealer or
for reference in case the vehicle is sto-
len.
1. KEY IDENTIFICATION NUMBER:CA-02E2. VEHICLE IDENTIFICATION
NUMBER:CA-02E3. MODEL LABEL INFORMATION:CA-01EEAU01041
Key identification numberThe key identification number is
stamped on the key tag. Record this
number in the space provided and use
it for reference when obtaining a new
key.
EAU01043
Vehicle identification numberThe vehicle identification number is
stamped into the steering head pipe.
Record this number in the space pro-
vided.NOTE:@ The vehicle identification number is
used to identify your motorcycle and
may be used to register your motor-
cycle with the licensing authority in
your state. @
1. Key identification number
1. Vehicle identification number
E_3mw.book Page 1 Monday, February 5, 2001 9:54 AM